Back to section

NavArch Handbook

Chapter 4 / Section 4.7

Hydrostatic particulars: KB, BM, KM, LCB, LCF

Definitions (all heights above the moulded baseline, K)

  • KBKBKB — height of the centre of buoyancy (centroid of the immersed volume).
  • BMTBM_TBMT​ — transverse metacentric radius, the distance from BBB to the transverse metacentre MMM: BMT=IT/∇BM_T = I_T/\nablaBMT​=IT​/∇.
  • KMT=KB+BMTKM_T = KB + BM_TKMT​=KB+BMT​ — height of the transverse metacentre. It depends only on the hull geometry and the draught; it is the key quantity read from the hydrostatic curves for stability work.
  • BML=IL/∇BM_L = I_L/\nablaBML​=IL​/∇, KML=KB+BMLKM_L = KB + BM_LKML​=KB+BML​ — longitudinal equivalents (large: typically BML≈LBM_L \approx LBML​≈L).
  • LCBLCBLCB — longitudinal centre of buoyancy, from midship or AP.
  • LCFLCFLCF — longitudinal centre of flotation, the centroid of the waterplane; the ship trims about a transverse axis through the LCF.

Approximate formulas (for early design or checking)

  • KBKBKB — Morrish's formula (good for normal forms): KB=T−13(T2+∇AWP)KB = T - \tfrac{1}{3}\left(\tfrac{T}{2} + \tfrac{\nabla}{A_{WP}}\right)KB=T−31​(2T​+AWP​∇​).
  • KBKBKB — Posdunine: KB=TCWPCWP+CBKB = T \dfrac{C_{WP}}{C_{WP} + C_B}KB=TCWP​+CB​CWP​​.
  • KB/TKB/TKB/T lies between 0.50 (rectangular section) and 0.667 (triangular section); typical ships 0.52–0.58.
  • BMT≈CIT B2CB TBM_T \approx \dfrac{C_{IT}\,B^2}{C_B\,T}BMT​≈CB​TCIT​B2​ with CIT=0.1216 CWP−0.0410C_{IT} = 0.1216\,C_{WP} - 0.0410CIT​=0.1216CWP​−0.0410 (Schneekluth & Bertram).
  • BML≈CIL L2CB TBM_L \approx \dfrac{C_{IL}\,L^2}{C_B\,T}BML​≈CB​TCIL​L2​ with CIL=0.350 CWP2−0.405 CWP+0.146C_{IL} = 0.350\,C_{WP}^2 - 0.405\,C_{WP} + 0.146CIL​=0.350CWP2​−0.405CWP​+0.146 (Schneekluth & Bertram).

Behaviour with draught

KBKBKB increases almost linearly with draught. BMTBM_TBMT​ decreases with draught (volume grows faster than ITI_TIT​) so KMTKM_TKMT​ usually has a minimum at an intermediate draught — the light condition may be the critical one for a vessel with a flat bottom and little flare.

Formulas

01Transverse metacentric radius
BMT=IT∇BM_T = \frac{I_T}{\nabla}BMT​=∇IT​​
SymbolDescriptionUnit
BMTBM_TBMT​Transverse metacentric radiusm
ITI_TIT​Second moment of waterplane area about centrelinem^4
∇\nabla∇Displacement volumem^3

Result unit m

02Height of transverse metacentre
KMT=KB+BMTKM_T = KB + BM_TKMT​=KB+BMT​
SymbolDescriptionUnit
KMTKM_TKMT​Height of transverse metacentre above baselinem
KBKBKBHeight of centre of buoyancym

Result unit m

03Longitudinal metacentric radius
BML=IL∇,KML=KB+BMLBM_L = \frac{I_L}{\nabla}, \qquad KM_L = KB + BM_LBML​=∇IL​​,KML​=KB+BML​
SymbolDescriptionUnit
ILI_LIL​Second moment of waterplane about transverse axis through LCFm^4

Result unit m

04Morrish's formula for KB
KB=T−13(T2+∇AWP)KB = T - \frac{1}{3}\left(\frac{T}{2} + \frac{\nabla}{A_{WP}}\right)KB=T−31​(2T​+AWP​∇​)
SymbolDescriptionUnit
TTTMean draughtm
AWPA_{WP}AWP​Waterplane area at draught Tm^2

Result unit m

Approximation; accurate to about ±1 % of T for conventional forms without large deadrise.

05Posdunine's formula for KB
KB=T CWPCWP+CBKB = T\,\frac{C_{WP}}{C_{WP} + C_B}KB=TCWP​+CB​CWP​​

Result unit m

06Schneekluth approximation for BM_T
BMT≈(0.1216 CWP−0.0410) B2CB TBM_T \approx \frac{(0.1216\,C_{WP} - 0.0410)\, B^2}{C_B\, T}BMT​≈CB​T(0.1216CWP​−0.0410)B2​

Result unit m

For 0.65 < C_WP < 0.95. First estimate only.

07Schneekluth approximation for BM_L
BML≈(0.350 CWP2−0.405 CWP+0.146) L2CB TBM_L \approx \frac{(0.350\,C_{WP}^2 - 0.405\,C_{WP} + 0.146)\, L^2}{C_B\, T}BML​≈CB​T(0.350CWP2​−0.405CWP​+0.146)L2​

Result unit m

First estimate only.

Tables

Typical hydrostatic ratios at design draught

QuantityTypical rangeComment
KB/TKB/TKB/T0.52–0.58Lower for full U-sections, higher for V-sections
BMT/BBM_T / BBMT​/B0.10–0.20Decreases with draught
KMT/BKM_T / BKMT​/B0.45–0.60 (merchant ships)PSVs and fishing vessels at the upper end
BML/LBM_L / LBML​/L0.9–1.3—
LCBLCBLCB from midship−3 % to +3 % of LBPL_{BP}LBP​Forward for full slow ships, aft for fast fine ships
LCFLCFLCF from midship−3 % to +1 % of LBPL_{BP}LBP​Usually aft of LCB because of fuller aft waterplane
Source: Compiled from Schneekluth & Bertram (1998) and Watson (1998).

Examples

#01

KB, KM and LCF for the 100 m vessel

Worked example

Problem

For the vessel of Examples 4.5 and 4.6 (T=5.50T = 5.50T=5.50 m, ∇=6160\nabla = 6160∇=6160 m³, AWP=1176A_{WP} = 1176AWP​=1176 m², IT=19,312I_T = 19{,}312IT​=19,312 m⁴, CB=0.700C_B = 0.700CB​=0.700, CWP=0.735C_{WP} = 0.735CWP​=0.735, B=16B = 16B=16 m, L=100L = 100L=100 m) estimate KBKBKB (Morrish), BMTBM_TBMT​, KMTKM_TKMT​, and BMLBM_LBML​ (Schneekluth).

Solution

Morrish:

KB=5.50−13(5.502+61601176)=5.50−13(2.750+5.238)=5.50−2.663=2.84 mKB = 5.50 - \frac{1}{3}\left(\frac{5.50}{2} + \frac{6160}{1176}\right) = 5.50 - \frac{1}{3}(2.750 + 5.238) = 5.50 - 2.663 = 2.84\ \text{m}KB=5.50−31​(25.50​+11766160​)=5.50−31​(2.750+5.238)=5.50−2.663=2.84 m

Check KB/T=0.516KB/T = 0.516KB/T=0.516 — within the typical range for a U-form.

BMT=19,3126160=3.14 m,KMT=2.84+3.14=5.98 mBM_T = \frac{19{,}312}{6160} = 3.14\ \text{m}, \qquad KM_T = 2.84 + 3.14 = 5.98\ \text{m}BMT​=616019,312​=3.14 m,KMT​=2.84+3.14=5.98 m

Longitudinal: CIL=0.350×0.7352−0.405×0.735+0.146=0.1891−0.2977+0.146=0.0374C_{IL} = 0.350 \times 0.735^2 - 0.405 \times 0.735 + 0.146 = 0.1891 - 0.2977 + 0.146 = 0.0374CIL​=0.350×0.7352−0.405×0.735+0.146=0.1891−0.2977+0.146=0.0374

BML≈0.0374×10020.700×5.50=3743.85=97.1 mBM_L \approx \frac{0.0374 \times 100^2}{0.700 \times 5.50} = \frac{374}{3.85} = 97.1\ \text{m}BML​≈0.700×5.500.0374×1002​=3.85374​=97.1 m

These values (KMTKM_TKMT​, BMLBM_LBML​, LCF=+0.88LCF = +0.88LCF=+0.88 m) are used in the Chapter 5 examples.

References

Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)Clause Vol. 1, Ch. 3 and Ch. 4 (Stability — metacentre)Textbook
Schneekluth & Bertram (1998)Clause Ch. 1.6 (Approximate formulae for KB, BM)Textbook
PNA Vol. I (1988)Clause Ch. 1, Sec. 6 (Hydrostatic curves)Textbook