Back to section

NavArch Handbook

Chapter 4 / Section 4.9

Wetted surface area approximations

The wetted surface SSS [m²] is needed for frictional resistance (Chapter 6), paint area and shell-plating weight. It is computed exactly by integrating the girths of the sections (Simpson's rule on girth × station spacing, with a correction for the longitudinal slope of the surface), or estimated from the formulas below.

Exact (girth) method

S=2∫0Lg(x) dx⋅ksS = 2\int_0^{L} g(x)\,dx \cdot k_sS=2∫0L​g(x)dx⋅ks​

where g(x)g(x)g(x) is the half-girth of the section from keel to waterline and ks≈1.01k_s \approx 1.01ks​≈1.01–1.031.031.03 accounts for the obliquity of the surface at the ends.

Empirical formulas

  1. Denny–Mumford: S=1.7 L T+∇TS = 1.7\,L\,T + \dfrac{\nabla}{T}S=1.7LT+T∇​ — simple, accurate to about ±5 % for normal merchant forms.
  2. Holtrop–Mennen (1982) — used inside the Holtrop power prediction method:
S=LWL (2T+B)CM (0.453+0.4425 CB−0.2862 CM−0.003467 BT+0.3696 CWP)+2.38 ABTCBS = L_{WL}\,(2T + B)\sqrt{C_M}\,\left(0.453 + 0.4425\,C_B - 0.2862\,C_M - 0.003467\,\frac{B}{T} + 0.3696\,C_{WP}\right) + 2.38\,\frac{A_{BT}}{C_B}S=LWL​(2T+B)CM​​(0.453+0.4425CB​−0.2862CM​−0.003467TB​+0.3696CWP​)+2.38CB​ABT​​

with ABTA_{BT}ABT​ the transverse bulb area at the FP (zero without bulb). Coefficients CBC_BCB​, CMC_MCM​, CWPC_{WP}CWP​ are based on LWLL_{WL}LWL​. 3. Taylor: S=CS∇ LS = C_S\sqrt{\nabla\,L}S=CS​∇L​ with CS≈2.5C_S \approx 2.5CS​≈2.5–2.72.72.7 for merchant forms (dimensionless when ∇\nabla∇ in m³ and LLL in m).

Appendages (rudder, bilge keels, shaft brackets) are added separately — typically 2–5 % of the hull wetted surface.

Formulas

01Denny–Mumford wetted surface
S=1.7 L T+∇TS = 1.7\,L\,T + \frac{\nabla}{T}S=1.7LT+T∇​
SymbolDescriptionUnit
SSSWetted surface of the bare hullm^2
LLLLength on waterline (or L_BP)m
TTTMean draughtm
∇\nabla∇Displacement volumem^3

Result unit m^2

±5 % for conventional forms.

02Holtrop–Mennen wetted surface
S=LWL(2T+B)CM(0.453+0.4425 CB−0.2862 CM−0.003467 BT+0.3696 CWP)+2.38 ABTCBS = L_{WL}(2T+B)\sqrt{C_M}\left(0.453 + 0.4425\,C_B - 0.2862\,C_M - 0.003467\,\tfrac{B}{T} + 0.3696\,C_{WP}\right) + 2.38\,\tfrac{A_{BT}}{C_B}S=LWL​(2T+B)CM​​(0.453+0.4425CB​−0.2862CM​−0.003467TB​+0.3696CWP​)+2.38CB​ABT​​
SymbolDescriptionUnit
ABTA_{BT}ABT​Transverse sectional area of bulbous bow at FP (0 if none)m^2
CB,CM,CWPC_B, C_M, C_{WP}CB​,CM​,CWP​Form coefficients on L_WL-

Result unit m^2

Holtrop, J. & Mennen, G.G.J., 'An approximate power prediction method', International Shipbuilding Progress, Vol. 29 (1982).

03Taylor wetted surface
S=CS∇ LS = C_S\sqrt{\nabla\, L}S=CS​∇L​
SymbolDescriptionUnit
CSC_SCS​Wetted surface coefficient (2.5–2.7 merchant; up to 2.9 fine forms)-

Result unit m^2

Examples

#01

Wetted surface of the example vessel by three methods

Worked example

Problem

LWL=102L_{WL} = 102LWL​=102 m, B=16B = 16B=16 m, T=5.5T = 5.5T=5.5 m, ∇=6160\nabla = 6160∇=6160 m³, CB=0.686C_B = 0.686CB​=0.686 (on LWLL_{WL}LWL​), CM=0.970C_M = 0.970CM​=0.970, CWP=0.721C_{WP} = 0.721CWP​=0.721 (on LWLL_{WL}LWL​), no bulb.

Solution

Denny–Mumford (with LWLL_{WL}LWL​): S=1.7×102×5.5+6160/5.5=953.7+1120.0=2074S = 1.7 \times 102 \times 5.5 + 6160/5.5 = 953.7 + 1120.0 = 2074S=1.7×102×5.5+6160/5.5=953.7+1120.0=2074 m².

Holtrop–Mennen: bracket =0.453+0.4425×0.686−0.2862×0.970−0.003467×2.909+0.3696×0.721=0.453+0.3036−0.2776−0.0101+0.2665=0.7354= 0.453 + 0.4425 \times 0.686 - 0.2862 \times 0.970 - 0.003467 \times 2.909 + 0.3696 \times 0.721 = 0.453 + 0.3036 - 0.2776 - 0.0101 + 0.2665 = 0.7354=0.453+0.4425×0.686−0.2862×0.970−0.003467×2.909+0.3696×0.721=0.453+0.3036−0.2776−0.0101+0.2665=0.7354. S=102×(11.0+16.0)×0.970×0.7354=102×27.0×0.9849×0.7354=1995S = 102 \times (11.0 + 16.0) \times \sqrt{0.970} \times 0.7354 = 102 \times 27.0 \times 0.9849 \times 0.7354 = 1995S=102×(11.0+16.0)×0.970​×0.7354=102×27.0×0.9849×0.7354=1995 m².

Taylor with CS=2.6C_S = 2.6CS​=2.6: S=2.66160×102=2.6×792.6=2061S = 2.6\sqrt{6160 \times 102} = 2.6 \times 792.6 = 2061S=2.66160×102​=2.6×792.6=2061 m².

The three estimates agree within ±4 %; adopt the Holtrop–Mennen value when it will be used inside a Holtrop resistance prediction, and the girth integration for painting and plating areas.

References

Holtrop & Mennen, International Shipbuilding Progress Vol. 29, No. 335 (1982)Clause Eq. for S (wetted area)Textbook
Rawson & Tupper (2001)Clause Vol. 1, Ch. 3 (Wetted surface)Textbook