NavArch Handbook
Chapter 1 / Section 1.1
The International System of Units (SI, BIPM 9th edition 2019) is the only system used in this handbook. Seven base units: metre (m), kilogram (kg), second (s), ampere (A), kelvin (K), mole (mol), candela (cd). Derived units used in naval architecture:
See the table below. In naval architecture: mm for plate thicknesses and scantlings, m for ship dimensions, kN and MN for forces, kPa for sea pressures, MPa for stresses, GPa for elastic moduli (206 GPa = 206 000 MPa).
See the table "Physical constants and standard values" below.
Result unit m/s
| Symbol | Description | Unit |
|---|---|---|
| Weight (force) | kN when m in t | |
| Mass | t | |
| Standard gravity 9.80665 (use 9.81) | m/s² |
Result unit kN
1 t × 9.81 m/s² = 9.81 kN. Mass moments in t·m convert to kN·m by the same factor.
| Symbol | Description | Unit |
|---|---|---|
| Hydrostatic pressure | kPa when ρ in t/m³ | |
| Fluid density | t/m³ | |
| Head (depth below free surface) | m |
Result unit kPa
Seawater: p = 1.025 × 9.81 × h = 10.06 h kPa.
| Prefix | Symbol | Factor | Typical use |
|---|---|---|---|
| giga | G | 10^9 | GPa (elastic modulus), GN·m (hull girder moments on large ships) |
| mega | M | 10^6 | MPa (stress), MN, MN·m |
| kilo | k | 10^3 | kN, kPa (sea pressure), kW |
| — | — | 1 | m, N, Pa, W |
| centi | c | 10^-2 | cm (TPC, MCT1cm; section properties in cm³, cm⁴ in rule formulas) |
| milli | m | 10^-3 | mm (scantlings, deflections, FWA) |
| micro | μ | 10^-6 | μm (surface roughness), με (microstrain) |
| Quantity | Unit | Equals (SI) | Note |
|---|---|---|---|
| Length | 1 nautical mile (NM) | 1852 m | exact (1929 international) |
| Length | 1 foot | 0.3048 m | exact |
| Length | 1 inch | 25.4 mm | exact |
| Length | 1 fathom | 1.8288 m | 6 ft |
| Length | 1 cable (UK) | 185.2 m | 1/10 NM |
| Speed | 1 knot | 0.514444 m/s = 1.852 km/h | exact |
| Mass | 1 tonne (t) | 1000 kg | exact |
| Mass | 1 long ton (UK) | 1016.0469 kg | 2240 lb |
| Mass | 1 short ton (US) | 907.1847 kg | 2000 lb |
| Mass | 1 pound (lb) | 0.45359237 kg | exact |
| Force | 1 kgf | 9.80665 N | exact |
| Force | 1 tf (tonne-force) | 9.80665 kN | exact |
| Force | 1 lbf | 4.4482216 N | exact |
| Pressure | 1 bar | 100 kPa = 0.1 MPa | exact |
| Pressure | 1 atm | 101.325 kPa | exact |
| Pressure | 1 psi | 6.894757 kPa | exact |
| Pressure | 1 m head fresh water (ρ = 1.000) | 9.80665 kPa | — |
| Pressure | 1 m head seawater (ρ = 1.025) | 10.0518 kPa | — |
| Stress | 1 ksi | 6.894757 MPa | exact |
| Stress | 1 kgf/mm² | 9.80665 MPa | exact |
| Power | 1 hp (metric, PS, CV) | 735.49875 W | exact |
| Power | 1 hp (imperial / mechanical) | 745.69987 W | exact |
| Energy | 1 kWh | 3.6 MJ | exact |
| Volume | 1 litre | 0.001 m³ | exact |
| Volume | 1 US gallon | 3.785412 L | exact |
| Volume | 1 imperial gallon | 4.54609 L | exact |
| Volume | 1 barrel (oil) | 158.9873 L | 42 US gal |
| Angle | 1 degree | 0.01745329 rad | π/180 |
| Angle | 1 m·rad | 57.2958 m·deg | GZ-curve areas |
| Quantity | Symbol | Value | Source / note |
|---|---|---|---|
| Standard gravity | 9.80665 m/s² (use 9.81) | CGPM 1901 | |
| Seawater density (standard) | 1.025 t/m³ | ICLL 1966 Annex I Reg. 40 | |
| Fresh water density | 1.000 t/m³ | 4 °C; 0.998 at 20 °C | |
| Air density (15 °C, 1 atm) | 1.225 kg/m³ | ISA sea level; IS Code wind pressure 504 Pa | |
| Kinematic viscosity seawater 15 °C | 1.1883 × 10⁻⁶ m²/s | ITTC Recommended Procedure 7.5-02-01-03 | |
| Kinematic viscosity fresh water 15 °C | 1.1386 × 10⁻⁶ m²/s | ITTC 7.5-02-01-03 | |
| Atmospheric pressure | 101.325 kPa | standard | |
| Steel, Young's modulus | 206 000 MPa (DNV: 2.06 × 10⁵ N/mm²) | DNV Rules Pt.3 Ch.3; EC3 uses 210 000 | |
| Steel, shear modulus | 79 000 MPa (E/2(1+ν) = 79 230) | — | |
| Steel, Poisson's ratio | 0.30 | — | |
| Steel, density | 7.85 t/m³ (7850 kg/m³) | — | |
| Steel, thermal expansion | 12 × 10⁻⁶ /K | — | |
| Aluminium 5083, E | 70 000 MPa | DNV Rules Pt.2 Ch.2 | |
| Aluminium, density | 2.66–2.70 t/m³ | — | |
| Aluminium, thermal expansion | 23 × 10⁻⁶ /K | — | |
| Speed of sound in seawater | ≈ 1500 m/s | sonar / echo sounder |
Worked example
Problem
The example vessel ( m) has a service speed of 15.0 knots and a delivered power of 4000 kW. Express the speed in m/s and km/h, compute the Froude number, and convert the power to metric and imperial horsepower.
Solution
The 1.4 % difference between the two horsepower units is a frequent source of error when comparing engine brochures.
Free download from bipm.org.
Rules for writing symbols, units and numbers.