NavArch Handbook
Chapter 1 / Section 1.5
For any solid whose cross-sectional area is known along an axis:
This is how the displacement and LCB (Section 4.4, 4.6) and tank volumes are computed from station areas or waterplane areas, with Simpson's rules doing the integration.
See the table. In ship work the most frequent are: the prism (tanks of constant section, parallel middle body), the wedge (immersed and emerged wedges in heel and trim; hopper tanks), the frustum of a pyramid/cone (tapered tanks, deck houses) and Pappus–Guldinus for revolved shapes (domes, masts, bulbous bows).
Used for the centre of gravity of lightship items (built from steel blocks and equipment), the centroid of tank contents (vertical centre of liquid, VCG of each tank at each filling), and the centre of buoyancy.
A tank's volume and centroid are tabulated against sounding (or ullage) by integrating the horizontal sections of the tank at closely spaced heights; the free-surface second moment (Section 5.3) is tabulated at the same levels. For trim and heel, the calibration is repeated or corrected. Rectangular tanks with sloped (hopper) sides are trapezoidal prisms — see the example.
Steel weight of a plated surface with the developed area and the thickness; add 5–10 % for stiffeners, brackets and welds in early estimates (Section 12.3 for small craft; Ch. 7 for ship structures).
| Symbol | Description | Unit |
|---|---|---|
| Cross-sectional area at x | m² | |
| Volume | m³ | |
| Centroid position along x | m |
Result unit m³
| Symbol | Description | Unit |
|---|---|---|
| Volume of part i | m³ | |
| Centroid of part i | m |
Result unit m
| Symbol | Description | Unit |
|---|---|---|
| Distance of the centroid of the generating area from the axis | m | |
| Generating area | m² |
Result unit m³
| Symbol | Description | Unit |
|---|---|---|
| Length of the generating curve | m |
Result unit m²
| Symbol | Description | Unit |
|---|---|---|
| Width at the top | m | |
| Width at the bottom | m | |
| Height | m | |
| Length of the prism | m |
Result unit m³
| Symbol | Description | Unit |
|---|---|---|
| Developed plate area | m² | |
| Thickness | m |
Result unit t
| Solid | Volume | Centroid (from base) | Surface area |
|---|---|---|---|
| Prism / cylinder, base area A, height h | lateral: perimeter × h | ||
| Circular cylinder, diameter d, length ℓ | (lateral) | ||
| Pyramid / cone, base area A, height h | cone lateral: | ||
| Frustum of cone, radii R (base), r (top), height h | |||
| Frustum of pyramid, base areas A_1 (base), A_2 (top), height h | — | ||
| Sphere, radius r | (centre) | ||
| Hemisphere (flat face as base) | (curved) | ||
| Wedge: rectangular base b × ℓ, height h along ℓ (triangular section) | above base; from the thick end | — | |
| Ellipsoid, semi-axes a, b, c | centre | — | |
| Torus, tube radius r, centre radius R | centre |
Worked example
Problem
A double-bottom MGO tank has a trapezoidal cross-section: 8.0 m wide at the top, 6.0 m at the bottom, 1.50 m high, and is 12.0 m long. The tank bottom is 0.20 m above the keel. Find the full volume, the mass of MGO (0.85 t/m³) at 98 % filling, and the vertical centre of gravity of the liquid above the keel when full.
Solution
Section area: . Volume: .
Mass at 98 %: .
Centroid above the tank bottom: . Above the keel: (full). At 98 % the liquid surface is slightly lower; for stability the VCG at the actual filling is read from the tank calibration table, and the free surface moment at that level is with the width at the liquid surface (≈ 7.97 m): , t·m (compare Example 5.3).