NavArch Handbook
Chapter 2 / Section 2.2
Stress , elongation , axial stiffness . Pillars, stays, tie rods, mast legs, crane boom members. Compression members must also be checked for buckling (Section 2.10) — for slender members buckling, not yield, governs.
When several members share a load, the distribution follows the stiffnesses: for parallel members . Example: a deck load carried by a pillar and by the surrounding bulkhead; a shaft line with several bearings.
Free thermal strain (steel /K). A member free to expand carries no stress; a member fully restrained carries — for steel, 2.47 MPa per kelvin, i.e. a 40 K change in a restrained member gives 99 MPa. Sources: heated cargo tanks, exhaust uptakes, sun-heated deck vs sea-cooled bottom (hull girder thermal deflection of a few centimetres on a 100 m ship), welding (residual stresses of yield magnitude), aluminium–steel interfaces ( ratio ≈ 2).
Compressive contact stress on a projected area: for a pin or bolt of diameter in a plate of thickness ; for a bedplate on a foundation top plate. Governs plate tear-out and bedding design.
A load at eccentricity from the centroid of the bolt group produces a direct shear on each bolt plus a torsional shear from the moment :
acting perpendicular to the radius from the centroid; components , . The critical bolt is the one farthest from the centroid where the torsional and direct components add.
Fillet weld throat stress with the throat thickness and the effective length; the simplified EN 1993-1-8 check: . Class rules give the required throat as a factor times the plate thickness (Section 8.3).
| Symbol | Description | Unit |
|---|---|---|
| Axial force | N | |
| Length | mm | |
| Cross-sectional area | mm² |
Result unit mm
| Symbol | Description | Unit |
|---|---|---|
| Axial stiffness of member i | N/mm |
Result unit N
| Symbol | Description | Unit |
|---|---|---|
| Coefficient of linear thermal expansion (steel 12 × 10⁻⁶, aluminium 23 × 10⁻⁶) | 1/K | |
| Temperature change | K |
Result unit MPa
Steel: 2.47 MPa per K when fully restrained.
| Symbol | Description | Unit |
|---|---|---|
| Bolt/pin diameter | mm | |
| Plate thickness | mm |
Result unit MPa
| Symbol | Description | Unit |
|---|---|---|
| Ultimate tensile strength of the bolt (8.8: 800) | MPa | |
| Tensile stress area (M16: 157, M20: 245, M24: 353, M30: 561) | mm² |
Result unit N
Result unit N
| Symbol | Description | Unit |
|---|---|---|
| Applied load | kN | |
| Eccentricity of P from the bolt-group centroid | mm | |
| Distance of bolt i from the centroid | mm | |
| Number of bolts | - |
Result unit kN
F_Mx,i = M y_i / Σr², F_My,i = M x_i / Σr² (perpendicular to r_i).
| Symbol | Description | Unit |
|---|---|---|
| Throat thickness (≈ 0.7 × leg length) | mm | |
| Effective weld length | mm | |
| Correlation factor (S235: 0.80; S355: 0.90) | - |
Result unit MPa
| Size | Pitch [mm] | Tensile stress area [mm²] | Shear resistance [kN] (8.8, single shear) | Tension resistance [kN] (8.8) | Preload [kN] (8.8) |
|---|---|---|---|---|---|
| M12 | 1.75 | 84.3 | 32.4 | 48.6 | 47.2 |
| M16 | 2.0 | 157 | 60.3 | 90.4 | 87.9 |
| M20 | 2.5 | 245 | 94.1 | 141.1 | 137.2 |
| M24 | 3.0 | 353 | 135.6 | 203.3 | 197.7 |
| M27 | 3.0 | 459 | 176.3 | 264.4 | 257.0 |
| M30 | 3.5 | 561 | 215.4 | 323.1 | 314.2 |
| M36 | 4.0 | 817 | 313.7 | 470.6 | 457.5 |
Worked example
Problem
A winch bracket is bolted to a bulkhead stiffener flange with six M20 grade 8.8 bolts in two vertical rows 80 mm apart (x = ±40 mm), three per row at y = 0, ±80 mm. A vertical load P = 60 kN acts in the plane of the connection at e = 150 mm horizontally from the bolt-group centroid. Bracket plate 12 mm, S235. Check the bolts in shear and the plate in bearing.
Solution
Direct shear per bolt: kN (vertical).
Moment: kN·mm. mm².
Corner bolt (, , mm): kN (horizontal); kN (vertical, adding to the direct shear on the bolts on the side of the load).
Bolt shear: kN (table) → ✓. Average shear stress in the bolt MPa.
Bearing on the 12 mm plate: MPa; EN 1993-1-8 bearing resistance with : kN → ✓.
The connection is adequate; the governing element is the corner bolt on the load side. If the load were dynamic (winch brake), apply the dynamic factor of the governing standard to P before the check, and consider a preloaded (slip-resistant) connection to avoid fretting.
Worked example
Problem
A steel exhaust uptake 6.0 m long is rigidly fixed at both ends and heats from 20 °C to 180 °C. Find the thermal stress if no expansion joint is fitted, and the free expansion if one end is released.
Solution
K. Fully restrained: MPa (compression) — above yield for any hull steel; the pipe would buckle or the supports would fail. Free expansion: mm, which the expansion bellows must accommodate. This is why uptakes, heated cargo lines and long pipe runs have expansion joints or sliding supports.
Used here as the reference method for bolted connections; class rules for seatings refer to manufacturer specifications.
For crane pedestals and slew-ring bolting; confirm edition in force.