NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.2 Axial loading, thermal stress and simple connections

Chapter 2 / Section 2.2

Axial loading, thermal stress and simple connections

Print this section

Axially loaded members

Stress σ=N/A\sigma = N/Aσ=N/A, elongation δ=NLEA\delta = \dfrac{N L}{E A}δ=EANL​, axial stiffness k=EA/Lk = EA/Lk=EA/L. Pillars, stays, tie rods, mast legs, crane boom members. Compression members must also be checked for buckling (Section 2.10) — for slender members buckling, not yield, governs.

Statically indeterminate axial systems

When several members share a load, the distribution follows the stiffnesses: for parallel members Ni=N⋅ki/∑kjN_i = N \cdot k_i / \sum k_jNi​=N⋅ki​/∑kj​. Example: a deck load carried by a pillar and by the surrounding bulkhead; a shaft line with several bearings.

Thermal strain and thermal stress

Free thermal strain εT=α ΔT\varepsilon_T = \alpha\,\Delta TεT​=αΔT (steel α=12×10−6\alpha = 12 \times 10^{-6}α=12×10−6/K). A member free to expand carries no stress; a member fully restrained carries σ=−E α ΔT\sigma = -E\,\alpha\,\Delta Tσ=−EαΔT — for steel, 2.47 MPa per kelvin, i.e. a 40 K change in a restrained member gives 99 MPa. Sources: heated cargo tanks, exhaust uptakes, sun-heated deck vs sea-cooled bottom (hull girder thermal deflection of a few centimetres on a 100 m ship), welding (residual stresses of yield magnitude), aluminium–steel interfaces (α\alphaα ratio ≈ 2).

Bearing stress

Compressive contact stress on a projected area: σb=F/(d t)\sigma_b = F/(d\,t)σb​=F/(dt) for a pin or bolt of diameter ddd in a plate of thickness ttt; σb=F/Acontact\sigma_b = F/A_{\text{contact}}σb​=F/Acontact​ for a bedplate on a foundation top plate. Governs plate tear-out and bedding design.

Bolted connections (EN 1993-1-8 approach, general level)

  • Shear per bolt (bearing-type connection): Fv=V/nF_v = V/nFv​=V/n for a concentric load; shear resistance Fv,Rd=αvfubAs/γM2F_{v,Rd} = \alpha_v f_{ub} A_s/\gamma_{M2}Fv,Rd​=αv​fub​As​/γM2​ with αv=0.6\alpha_v = 0.6αv​=0.6 (grades 4.6, 5.6, 8.8) or 0.5 (grades 4.8, 5.8, 6.8, 10.9), AsA_sAs​ the tensile stress area, γM2=1.25\gamma_{M2} = 1.25γM2​=1.25.
  • Bearing resistance of the plate: Fb,Rd=k1αbfudt/γM2F_{b,Rd} = k_1 \alpha_b f_u d t/\gamma_{M2}Fb,Rd​=k1​αb​fu​dt/γM2​ (coefficients depend on edge and end distances; typical k1αb≈2.0k_1\alpha_b \approx 2.0k1​αb​≈2.0–2.52.52.5).
  • Tension: Ft,Rd=0.9fubAs/γM2F_{t,Rd} = 0.9 f_{ub} A_s/\gamma_{M2}Ft,Rd​=0.9fub​As​/γM2​; combined shear and tension: FvFv,Rd+Ft1.4Ft,Rd≤1.0\dfrac{F_v}{F_{v,Rd}} + \dfrac{F_t}{1.4 F_{t,Rd}} \le 1.0Fv,Rd​Fv​​+1.4Ft,Rd​Ft​​≤1.0.
  • Preloaded (slip-resistant) connections: preload Fp=0.7fubAsF_p = 0.7 f_{ub} A_sFp​=0.7fub​As​; slip resistance =ksnμFp/γM3= k_s n \mu F_p/\gamma_{M3}=ks​nμFp​/γM3​ with friction coefficient μ\muμ = 0.2–0.5 by surface class. Used for crane slew rings, engine holding-down, equipment that must not move under vibration.
  • Class rules for machinery and equipment seatings reference the manufacturer's bolt specification and torque; the hull rules usually require welded foundations. For offshore lifting appliances DNV-ST-0378 gives bolt design requirements.

Eccentrically loaded bolt groups (in-plane)

A load PPP at eccentricity eee from the centroid of the bolt group produces a direct shear P/nP/nP/n on each bolt plus a torsional shear from the moment M=P eM = P\,eM=Pe:

FM,i=M ri∑rj2F_{M,i} = \frac{M\,r_i}{\sum r_j^2}FM,i​=∑rj2​Mri​​

acting perpendicular to the radius rir_iri​ from the centroid; components FMx,i=M yi/∑rj2F_{Mx,i} = M\,y_i/\sum r_j^2FMx,i​=Myi​/∑rj2​, FMy,i=M xi/∑rj2F_{My,i} = M\,x_i/\sum r_j^2FMy,i​=Mxi​/∑rj2​. The critical bolt is the one farthest from the centroid where the torsional and direct components add.

Welded connections

Fillet weld throat stress τ=F/(a ℓeff)\tau = F/(a\,\ell_{\text{eff}})τ=F/(aℓeff​) with aaa the throat thickness and ℓeff\ell_{\text{eff}}ℓeff​ the effective length; the simplified EN 1993-1-8 check: Fw,Ed≤Fw,Rd=a ℓ fu/(3 βw γM2)F_{w,Ed} \le F_{w,Rd} = a\,\ell\,f_u/(\sqrt 3\,\beta_w\,\gamma_{M2})Fw,Ed​≤Fw,Rd​=aℓfu​/(3​βw​γM2​). Class rules give the required throat as a factor times the plate thickness (Section 8.3).

Formulas

01Axial elongation
δ=N LE A\delta = \frac{N\,L}{E\,A}δ=EANL​
SymbolDescriptionUnit
NNNAxial forceN
LLLLengthmm
AAACross-sectional areamm²

Result unit mm

02Load sharing between parallel members
Ni=N ki∑jkj,ki=EiAiLiN_i = N\,\frac{k_i}{\sum_j k_j}, \qquad k_i = \frac{E_i A_i}{L_i}Ni​=N∑j​kj​ki​​,ki​=Li​Ei​Ai​​
SymbolDescriptionUnit
kik_iki​Axial stiffness of member iN/mm

Result unit N

03Thermal strain and restrained thermal stress
εT=α ΔT,σT=−E α ΔT  (fully restrained)\varepsilon_T = \alpha\,\Delta T, \qquad \sigma_T = -E\,\alpha\,\Delta T \ \ (\text{fully restrained})εT​=αΔT,σT​=−EαΔT  (fully restrained)
SymbolDescriptionUnit
α\alphaαCoefficient of linear thermal expansion (steel 12 × 10⁻⁶, aluminium 23 × 10⁻⁶)1/K
ΔT\Delta TΔTTemperature changeK

Result unit MPa

Steel: 2.47 MPa per K when fully restrained.

04Bearing stress on a bolt or pin
σb=Fd t\sigma_b = \frac{F}{d\,t}σb​=dtF​
SymbolDescriptionUnit
dddBolt/pin diametermm
tttPlate thicknessmm

Result unit MPa

05Bolt shear resistance (EN 1993-1-8)
Fv,Rd=αv fub AsγM2,αv=0.6 (4.6,5.6,8.8), 0.5 (10.9),γM2=1.25F_{v,Rd} = \frac{\alpha_v\, f_{ub}\, A_s}{\gamma_{M2}}, \qquad \alpha_v = 0.6\ (4.6, 5.6, 8.8),\ 0.5\ (10.9), \quad \gamma_{M2} = 1.25Fv,Rd​=γM2​αv​fub​As​​,αv​=0.6 (4.6,5.6,8.8), 0.5 (10.9),γM2​=1.25
SymbolDescriptionUnit
fubf_{ub}fub​Ultimate tensile strength of the bolt (8.8: 800)MPa
AsA_sAs​Tensile stress area (M16: 157, M20: 245, M24: 353, M30: 561)mm²

Result unit N

06Bolt tension resistance and combined check (EN 1993-1-8)
Ft,Rd=0.9 fub AsγM2,Fv,EdFv,Rd+Ft,Ed1.4 Ft,Rd≤1.0F_{t,Rd} = \frac{0.9\, f_{ub}\, A_s}{\gamma_{M2}}, \qquad \frac{F_{v,Ed}}{F_{v,Rd}} + \frac{F_{t,Ed}}{1.4\,F_{t,Rd}} \le 1.0Ft,Rd​=γM2​0.9fub​As​​,Fv,Rd​Fv,Ed​​+1.4Ft,Rd​Ft,Ed​​≤1.0

Result unit N

07Eccentric bolt group — force on bolt i
FM,i=P e ri∑jrj2,Fi=(Pxn+FMx,i)2+(Pyn+FMy,i)2F_{M,i} = \frac{P\,e\,r_i}{\sum_j r_j^2}, \qquad F_{i} = \sqrt{\left(\frac{P_x}{n} + F_{Mx,i}\right)^2 + \left(\frac{P_y}{n} + F_{My,i}\right)^2}FM,i​=∑j​rj2​Peri​​,Fi​=(nPx​​+FMx,i​)2+(nPy​​+FMy,i​)2​
SymbolDescriptionUnit
PPPApplied loadkN
eeeEccentricity of P from the bolt-group centroidmm
rir_iri​Distance of bolt i from the centroidmm
nnnNumber of bolts-

Result unit kN

F_Mx,i = M y_i / Σr², F_My,i = M x_i / Σr² (perpendicular to r_i).

08Fillet weld throat stress (simplified)
τw=Fa ℓeff≤fu3 βw γM2\tau_w = \frac{F}{a\,\ell_{\text{eff}}} \le \frac{f_u}{\sqrt 3\,\beta_w\,\gamma_{M2}}τw​=aℓeff​F​≤3​βw​γM2​fu​​
SymbolDescriptionUnit
aaaThroat thickness (≈ 0.7 × leg length)mm
ℓeff\ell_{\text{eff}}ℓeff​Effective weld lengthmm
βw\beta_wβw​Correlation factor (S235: 0.80; S355: 0.90)-

Result unit MPa

Tables

Metric bolt data (coarse thread) and EN 1993-1-8 resistances for grade 8.8

SizePitch [mm]Tensile stress area AsA_sAs​ [mm²]Shear resistance Fv,RdF_{v,Rd}Fv,Rd​ [kN] (8.8, single shear)Tension resistance Ft,RdF_{t,Rd}Ft,Rd​ [kN] (8.8)Preload Fp=0.7fubAsF_p = 0.7 f_{ub} A_sFp​=0.7fub​As​ [kN] (8.8)
M121.7584.332.448.647.2
M162.015760.390.487.9
M202.524594.1141.1137.2
M243.0353135.6203.3197.7
M273.0459176.3264.4257.0
M303.5561215.4323.1314.2
M364.0817313.7470.6457.5
Source: ISO 898-1 (stress areas); EN 1993-1-8:2005 Table 3.4 (α_v = 0.6, γ_M2 = 1.25) and clause 3.9 (preload). For grade 10.9 multiply shear by 1.25 × 0.5/0.6 = 1.04 and tension/preload by 1.25.

Examples

#01

Eccentrically loaded bolt group on a bracket

Worked example

Problem

A winch bracket is bolted to a bulkhead stiffener flange with six M20 grade 8.8 bolts in two vertical rows 80 mm apart (x = ±40 mm), three per row at y = 0, ±80 mm. A vertical load P = 60 kN acts in the plane of the connection at e = 150 mm horizontally from the bolt-group centroid. Bracket plate 12 mm, S235. Check the bolts in shear and the plate in bearing.

Solution

Direct shear per bolt: P/n=60/6=10.0P/n = 60/6 = 10.0P/n=60/6=10.0 kN (vertical).

Moment: M=60×150=9000M = 60 \times 150 = 9000M=60×150=9000 kN·mm. ∑r2=6×402+4×802=9600+25 600=35 200\sum r^2 = 6 \times 40^2 + 4 \times 80^2 = 9600 + 25\,600 = 35\,200∑r2=6×402+4×802=9600+25600=35200 mm².

Corner bolt (x=40x = 40x=40, y=80y = 80y=80, r=89.4r = 89.4r=89.4 mm): FMx=9000×80/35 200=20.45F_{Mx} = 9000 \times 80/35\,200 = 20.45FMx​=9000×80/35200=20.45 kN (horizontal); FMy=9000×40/35 200=10.23F_{My} = 9000 \times 40/35\,200 = 10.23FMy​=9000×40/35200=10.23 kN (vertical, adding to the direct shear on the bolts on the side of the load).

F=20.452+(10.0+10.23)2=418.2+409.3=28.8 kNF = \sqrt{20.45^2 + (10.0 + 10.23)^2} = \sqrt{418.2 + 409.3} = 28.8\ \text{kN}F=20.452+(10.0+10.23)2​=418.2+409.3​=28.8 kN

Bolt shear: Fv,Rd=94.1F_{v,Rd} = 94.1Fv,Rd​=94.1 kN (table) → UC=28.8/94.1=0.31UC = 28.8/94.1 = 0.31UC=28.8/94.1=0.31 ✓. Average shear stress in the bolt =28 800/245=118= 28\,800/245 = 118=28800/245=118 MPa.

Bearing on the 12 mm plate: σb=28 800/(20×12)=120\sigma_b = 28\,800/(20 \times 12) = 120σb​=28800/(20×12)=120 MPa; EN 1993-1-8 bearing resistance with k1αb≈2.0k_1\alpha_b \approx 2.0k1​αb​≈2.0: Fb,Rd=2.0×360×20×12/1.25=138F_{b,Rd} = 2.0 \times 360 \times 20 \times 12/1.25 = 138Fb,Rd​=2.0×360×20×12/1.25=138 kN → UC=0.21UC = 0.21UC=0.21 ✓.

The connection is adequate; the governing element is the corner bolt on the load side. If the load were dynamic (winch brake), apply the dynamic factor of the governing standard to P before the check, and consider a preloaded (slip-resistant) connection to avoid fretting.

#02

Thermal stress in a restrained exhaust-pipe support

Worked example

Problem

A steel exhaust uptake 6.0 m long is rigidly fixed at both ends and heats from 20 °C to 180 °C. Find the thermal stress if no expansion joint is fitted, and the free expansion if one end is released.

Solution

ΔT=160\Delta T = 160ΔT=160 K. Fully restrained: σT=−206 000×12×10−6×160=−395\sigma_T = -206\,000 \times 12 \times 10^{-6} \times 160 = -395σT​=−206000×12×10−6×160=−395 MPa (compression) — above yield for any hull steel; the pipe would buckle or the supports would fail. Free expansion: δ=12×10−6×160×6000=11.5\delta = 12 \times 10^{-6} \times 160 \times 6000 = 11.5δ=12×10−6×160×6000=11.5 mm, which the expansion bellows must accommodate. This is why uptakes, heated cargo lines and long pipe runs have expansion joints or sliding supports.

References

EN 1993-1-8:2005 Eurocode 3 — Design of steel structures — Part 1-8: Design of jointsClause Sec. 3 (Connections made with bolts), Sec. 4 (Welded connections)Recommended

Used here as the reference method for bolted connections; class rules for seatings refer to manufacturer specifications.

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 2 (Axially loaded members; thermal effects; statically indeterminate structures)Textbook
DNV-ST-0378 Standard for offshore and platform lifting appliancesClause Sec. 4 (Design — bolted connections and foundations)Mandatory

For crane pedestals and slew-ring bolting; confirm edition in force.

ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studsClause Tables of property classes and stress areasRecommended
Previous · 2.1Stress, strain and material constants (E, G, ν)Next · 2.3Shear force and bending moment diagrams

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Axially loaded members
  • Statically indeterminate axial systems
  • Thermal strain and thermal stress
  • Bearing stress
  • Bolted connections (EN 1993-1-8 approach, general level)
  • Eccentrically loaded bolt groups (in-plane)
  • Welded connections
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • EN 1993-1-8:2005 Eurocode 3 — Design of steel structures — Part 1-8: Design of joints

    Sec. 3 (Connections made with bolts), Sec. 4 (Welded connections)

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 2 (Axially loaded members; thermal effects; statically indeterminate structures)

  • DNV-ST-0378 Standard for offshore and platform lifting appliances

    Sec. 4 (Design — bolted connections and foundations)

  • ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs

    Tables of property classes and stress areas

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.