NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.1 Stress, strain and material constants (E, G, ν)

Chapter 2 / Section 2.1

Stress, strain and material constants (E, G, ν)

Print this section

Stress

Internal force per unit area. Normal stress σ=N/A\sigma = N/Aσ=N/A (tension positive); shear stress τ=V/A\tau = V/Aτ=V/A. Units: MPa = N/mm². The stress state at a point is described by the stress tensor (three normal and three shear components); for plates and beams, the plane stress state (σx,σy,τxy\sigma_x, \sigma_y, \tau_{xy}σx​,σy​,τxy​) is sufficient (Section 2.8).

Strain

Normal strain ε=δ/L\varepsilon = \delta/Lε=δ/L (dimensionless; often in microstrain, 1 με=10−61\ \mu\varepsilon = 10^{-6}1 με=10−6); shear strain γ\gammaγ (angle change, rad).

Hooke's law and elastic constants

In the linear elastic range:

σ=E ε,τ=G γ,εlateral=−ν εaxial\sigma = E\,\varepsilon, \qquad \tau = G\,\gamma, \qquad \varepsilon_{\text{lateral}} = -\nu\,\varepsilon_{\text{axial}}σ=Eε,τ=Gγ,εlateral​=−νεaxial​

The three constants are related: G=E2(1+ν)G = \dfrac{E}{2(1+\nu)}G=2(1+ν)E​. Only two are independent. For plane stress with both in-plane stresses:

εx=1E(σx−νσy),εy=1E(σy−νσx),γxy=τxyG\varepsilon_x = \frac{1}{E}(\sigma_x - \nu\sigma_y), \qquad \varepsilon_y = \frac{1}{E}(\sigma_y - \nu\sigma_x), \qquad \gamma_{xy} = \frac{\tau_{xy}}{G}εx​=E1​(σx​−νσy​),εy​=E1​(σy​−νσx​),γxy​=Gτxy​​

Inverse: σx=E1−ν2(εx+νεy)\sigma_x = \dfrac{E}{1-\nu^2}(\varepsilon_x + \nu\varepsilon_y)σx​=1−ν2E​(εx​+νεy​) — the factor 1/(1−ν2)1/(1-\nu^2)1/(1−ν2) is why plate bending stiffness is D=Et3/(12(1−ν2))D = Et^3/(12(1-\nu^2))D=Et3/(12(1−ν2)) and not Et3/12Et^3/12Et3/12 (Section 2.9).

Stress–strain curve of structural steel

Linear to the yield point σy\sigma_yσy​ (ReH, 235 MPa for grade A), then a yield plateau, strain hardening to the ultimate tensile strength σu\sigma_uσu​ (Rm, 400–520 MPa for grade A), necking, fracture at 20–25 % elongation. Design in classification rules is elastic: stresses are limited to a fraction of σy\sigma_yσy​ (Section 2.12). Higher-strength steels (AH32/36, σy\sigma_yσy​ = 315/355 MPa) have the same E — stiffness and buckling do not improve with yield strength, only the yield check does (Section 3.2).

Other material behaviour relevant to ships

  • Ductility and notch toughness (Charpy energy at the design temperature) govern grade selection (D, E grades for low temperature and thick plates).
  • Aluminium: EEE ≈ 70 000 MPa (one third of steel), so an aluminium structure needs three times the section inertia for the same deflection and is more buckling-prone; welded-zone strength is lower than parent (Section 3.3).
  • FRP: orthotropic; EEE in fibre direction 10–40 GPa; no yield — design to a fraction of ultimate strain (Section 3.5).
  • Residual stresses from welding are of yield magnitude; they do not affect the static strength check (elastic design absorbs them in the safety factor) but matter for fatigue and buckling.

Strain energy

U=12σεU = \dfrac{1}{2}\sigma\varepsilonU=21​σε per unit volume =σ22E= \dfrac{\sigma^2}{2E}=2Eσ2​. Basis of the energy methods (Castigliano) and of the dynamic stability analogy in Section 5.5.

Formulas

01Normal and shear stress
σ=NA,τ=VA\sigma = \frac{N}{A}, \qquad \tau = \frac{V}{A}σ=AN​,τ=AV​
SymbolDescriptionUnit
σ\sigmaσNormal stress (tension positive)MPa
τ\tauτAverage shear stressMPa
NNNNormal forceN
VVVShear forceN
AAACross-sectional areamm²

Result unit MPa

1 MPa = 1 N/mm². With N in kN and A in mm²: σ [MPa] = 1000 N/A.

02Normal strain
ε=δL\varepsilon = \frac{\delta}{L}ε=Lδ​
SymbolDescriptionUnit
δ\deltaδElongationmm
LLLOriginal lengthmm

Result unit -

03Hooke's law (uniaxial and shear)
σ=E ε,τ=G γ\sigma = E\,\varepsilon, \qquad \tau = G\,\gammaσ=Eε,τ=Gγ
SymbolDescriptionUnit
EEEYoung's modulus (steel 206 000)MPa
GGGShear modulus (steel 79 000)MPa
γ\gammaγShear strainrad

Result unit MPa

04Relation between E, G and ν
G=E2 (1+ν)G = \frac{E}{2\,(1+\nu)}G=2(1+ν)E​
SymbolDescriptionUnit
ν\nuνPoisson's ratio (steel 0.30)-

Result unit MPa

Steel: 206 000 / 2.6 = 79 230 MPa.

05Plane-stress Hooke's law
εx=σx−νσyE,εy=σy−νσxE,γxy=τxyG\varepsilon_x = \frac{\sigma_x - \nu\sigma_y}{E}, \quad \varepsilon_y = \frac{\sigma_y - \nu\sigma_x}{E}, \quad \gamma_{xy} = \frac{\tau_{xy}}{G}εx​=Eσx​−νσy​​,εy​=Eσy​−νσx​​,γxy​=Gτxy​​

Result unit -

06Plane-stress inverse relation
σx=E1−ν2(εx+ν εy),σy=E1−ν2(εy+ν εx)\sigma_x = \frac{E}{1-\nu^2}\left(\varepsilon_x + \nu\,\varepsilon_y\right), \qquad \sigma_y = \frac{E}{1-\nu^2}\left(\varepsilon_y + \nu\,\varepsilon_x\right)σx​=1−ν2E​(εx​+νεy​),σy​=1−ν2E​(εy​+νεx​)

Result unit MPa

07Elastic strain energy density
u=σ22E=12σ εu = \frac{\sigma^2}{2E} = \frac{1}{2}\sigma\,\varepsilonu=2Eσ2​=21​σε
SymbolDescriptionUnit
uuuStrain energy per unit volumeJ/m³ = Pa

Result unit MPa

Tables

Elastic constants and strengths of shipbuilding materials (design values)

MaterialEEE [MPa]GGG [MPa]ν\nuνYield / proof σy\sigma_yσy​ [MPa]Tensile σu\sigma_uσu​ [MPa]Density [t/m³]
Hull steel grade A/B/D/E206 00079 0000.30235400–5207.85
Hull steel AH32/DH32/EH32206 00079 0000.30315440–5707.85
Hull steel AH36/DH36/EH36206 00079 0000.30355490–6307.85
Hull steel AH40/DH40/EH40206 00079 0000.30390510–6607.85
Aluminium 5083-H116 (unwelded / welded)70 00026 5000.33215 / 125305 / 2752.66
Aluminium 6082-T6 (unwelded / welded)70 00026 5000.33260 / 115310 / 1702.70
Stainless 316L (annealed)193 00077 0000.30≥ 220≥ 5208.0
Duplex 1.4462200 00077 0000.30≥ 450≥ 6507.8
E-glass/polyester laminate (woven roving, ~35 % Vf), in-plane12 000–16 0003 0000.25— (ultimate ≈ 150–250)150–2501.6–1.9
Bolts grade 8.8206 00079 0000.306408007.85
Bolts grade 10.9206 00079 0000.3090010007.85
Source: IACS UR W11 (hull steels); DNV Rules Pt.2 Ch.2 (aluminium alloys, welded values indicative — confirm per temper and thickness); EN 10088 (stainless); ISO 898-1 (bolts); laminate values indicative, see Section 3.5 and ISO 12215-5 Annex C.

Examples

#01

Strain gauge reading on a deck plate

Worked example

Problem

A longitudinal strain gauge on the strength deck of the example vessel reads +420 με+420\ \mu\varepsilon+420 με in a hogging condition; a transverse gauge at the same point reads −95 με-95\ \mu\varepsilon−95 με. Assuming plane stress with negligible shear at the gauge, find the longitudinal and transverse stresses.

Solution

εx=420×10−6\varepsilon_x = 420 \times 10^{-6}εx​=420×10−6, εy=−95×10−6\varepsilon_y = -95 \times 10^{-6}εy​=−95×10−6, E=206 000E = 206\,000E=206000 MPa, ν=0.30\nu = 0.30ν=0.30.

σx=206 0001−0.09 (420−0.30×95)×10−6=226 374×391.5×10−6=88.6 MPa\sigma_x = \frac{206\,000}{1 - 0.09}\,(420 - 0.30 \times 95) \times 10^{-6} = 226\,374 \times 391.5 \times 10^{-6} = 88.6\ \text{MPa}σx​=1−0.09206000​(420−0.30×95)×10−6=226374×391.5×10−6=88.6 MPa σy=226 374×(−95+0.30×420)×10−6=226 374×31×10−6=7.0 MPa\sigma_y = 226\,374 \times (-95 + 0.30 \times 420) \times 10^{-6} = 226\,374 \times 31 \times 10^{-6} = 7.0\ \text{MPa}σy​=226374×(−95+0.30×420)×10−6=226374×31×10−6=7.0 MPa

Note that a uniaxial interpretation (σx=Eεx=86.5\sigma_x = E\varepsilon_x = 86.5σx​=Eεx​=86.5 MPa) would be 2.4 % low and would give a wrong (negative) transverse stress; the transverse gauge reading is largely the Poisson contraction, and the small positive σy\sigma_yσy​ indicates slight transverse restraint. The deck stress of 89 MPa is about 50 % of the IACS permissible hull girder stress 175 MPa for mild steel.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 1 (Tension, compression and shear), Ch. 7.5 (Hooke's law for plane stress)Textbook
Hibbeler, Mechanics of Materials, 10th ed. (2017)Clause Ch. 3 (Mechanical properties of materials), Ch. 10.6 (Material property relationships)Textbook
IACS Unified Requirement W11 Normal and higher strength hull structural steelsClause Tables of mechanical propertiesMandatory

Free download from iacs.org.uk.

DNV Rules for Classification — Ships, Pt.2 Ch.2 (Metallic materials)Clause Sec. 2 (Rolled steel), Sec. 9 (Aluminium alloys)Mandatory

Confirm edition in force.

Previous · 1.9Significant figures, rounding and reporting of resultsNext · 2.2Axial loading, thermal stress and simple connections

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Stress
  • Strain
  • Hooke's law and elastic constants
  • Stress–strain curve of structural steel
  • Other material behaviour relevant to ships
  • Strain energy
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 1 (Tension, compression and shear), Ch. 7.5 (Hooke's law for plane stress)

  • Hibbeler, Mechanics of Materials, 10th ed. (2017)

    Ch. 3 (Mechanical properties of materials), Ch. 10.6 (Material property relationships)

  • IACS Unified Requirement W11 Normal and higher strength hull structural steels

    Tables of mechanical properties

  • DNV Rules for Classification — Ships, Pt.2 Ch.2 (Metallic materials)

    Sec. 2 (Rolled steel), Sec. 9 (Aluminium alloys)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.