Back to section

NavArch Handbook

Chapter 2 / Section 2.1

Stress, strain and material constants (E, G, ν)

Stress

Internal force per unit area. Normal stress σ=N/A\sigma = N/Aσ=N/A (tension positive); shear stress τ=V/A\tau = V/Aτ=V/A. Units: MPa = N/mm². The stress state at a point is described by the stress tensor (three normal and three shear components); for plates and beams, the plane stress state (σx,σy,τxy\sigma_x, \sigma_y, \tau_{xy}σx​,σy​,τxy​) is sufficient (Section 2.8).

Strain

Normal strain ε=δ/L\varepsilon = \delta/Lε=δ/L (dimensionless; often in microstrain, 1 με=10−61\ \mu\varepsilon = 10^{-6}1 με=10−6); shear strain γ\gammaγ (angle change, rad).

Hooke's law and elastic constants

In the linear elastic range:

σ=E ε,τ=G γ,εlateral=−ν εaxial\sigma = E\,\varepsilon, \qquad \tau = G\,\gamma, \qquad \varepsilon_{\text{lateral}} = -\nu\,\varepsilon_{\text{axial}}σ=Eε,τ=Gγ,εlateral​=−νεaxial​

The three constants are related: G=E2(1+ν)G = \dfrac{E}{2(1+\nu)}G=2(1+ν)E​. Only two are independent. For plane stress with both in-plane stresses:

εx=1E(σx−νσy),εy=1E(σy−νσx),γxy=τxyG\varepsilon_x = \frac{1}{E}(\sigma_x - \nu\sigma_y), \qquad \varepsilon_y = \frac{1}{E}(\sigma_y - \nu\sigma_x), \qquad \gamma_{xy} = \frac{\tau_{xy}}{G}εx​=E1​(σx​−νσy​),εy​=E1​(σy​−νσx​),γxy​=Gτxy​​

Inverse: σx=E1−ν2(εx+νεy)\sigma_x = \dfrac{E}{1-\nu^2}(\varepsilon_x + \nu\varepsilon_y)σx​=1−ν2E​(εx​+νεy​) — the factor 1/(1−ν2)1/(1-\nu^2)1/(1−ν2) is why plate bending stiffness is D=Et3/(12(1−ν2))D = Et^3/(12(1-\nu^2))D=Et3/(12(1−ν2)) and not Et3/12Et^3/12Et3/12 (Section 2.9).

Stress–strain curve of structural steel

Linear to the yield point σy\sigma_yσy​ (ReH, 235 MPa for grade A), then a yield plateau, strain hardening to the ultimate tensile strength σu\sigma_uσu​ (Rm, 400–520 MPa for grade A), necking, fracture at 20–25 % elongation. Design in classification rules is elastic: stresses are limited to a fraction of σy\sigma_yσy​ (Section 2.12). Higher-strength steels (AH32/36, σy\sigma_yσy​ = 315/355 MPa) have the same E — stiffness and buckling do not improve with yield strength, only the yield check does (Section 3.2).

Other material behaviour relevant to ships

  • Ductility and notch toughness (Charpy energy at the design temperature) govern grade selection (D, E grades for low temperature and thick plates).
  • Aluminium: EEE ≈ 70 000 MPa (one third of steel), so an aluminium structure needs three times the section inertia for the same deflection and is more buckling-prone; welded-zone strength is lower than parent (Section 3.3).
  • FRP: orthotropic; EEE in fibre direction 10–40 GPa; no yield — design to a fraction of ultimate strain (Section 3.5).
  • Residual stresses from welding are of yield magnitude; they do not affect the static strength check (elastic design absorbs them in the safety factor) but matter for fatigue and buckling.

Strain energy

U=12σεU = \dfrac{1}{2}\sigma\varepsilonU=21​σε per unit volume =σ22E= \dfrac{\sigma^2}{2E}=2Eσ2​. Basis of the energy methods (Castigliano) and of the dynamic stability analogy in Section 5.5.

Formulas

01Normal and shear stress
σ=NA,τ=VA\sigma = \frac{N}{A}, \qquad \tau = \frac{V}{A}σ=AN​,τ=AV​
SymbolDescriptionUnit
σ\sigmaσNormal stress (tension positive)MPa
τ\tauτAverage shear stressMPa
NNNNormal forceN
VVVShear forceN
AAACross-sectional areamm²

Result unit MPa

1 MPa = 1 N/mm². With N in kN and A in mm²: σ [MPa] = 1000 N/A.

02Normal strain
ε=δL\varepsilon = \frac{\delta}{L}ε=Lδ​
SymbolDescriptionUnit
δ\deltaδElongationmm
LLLOriginal lengthmm

Result unit -

03Hooke's law (uniaxial and shear)
σ=E ε,τ=G γ\sigma = E\,\varepsilon, \qquad \tau = G\,\gammaσ=Eε,τ=Gγ
SymbolDescriptionUnit
EEEYoung's modulus (steel 206 000)MPa
GGGShear modulus (steel 79 000)MPa
γ\gammaγShear strainrad

Result unit MPa

04Relation between E, G and ν
G=E2 (1+ν)G = \frac{E}{2\,(1+\nu)}G=2(1+ν)E​
SymbolDescriptionUnit
ν\nuνPoisson's ratio (steel 0.30)-

Result unit MPa

Steel: 206 000 / 2.6 = 79 230 MPa.

05Plane-stress Hooke's law
εx=σx−νσyE,εy=σy−νσxE,γxy=τxyG\varepsilon_x = \frac{\sigma_x - \nu\sigma_y}{E}, \quad \varepsilon_y = \frac{\sigma_y - \nu\sigma_x}{E}, \quad \gamma_{xy} = \frac{\tau_{xy}}{G}εx​=Eσx​−νσy​​,εy​=Eσy​−νσx​​,γxy​=Gτxy​​

Result unit -

06Plane-stress inverse relation
σx=E1−ν2(εx+ν εy),σy=E1−ν2(εy+ν εx)\sigma_x = \frac{E}{1-\nu^2}\left(\varepsilon_x + \nu\,\varepsilon_y\right), \qquad \sigma_y = \frac{E}{1-\nu^2}\left(\varepsilon_y + \nu\,\varepsilon_x\right)σx​=1−ν2E​(εx​+νεy​),σy​=1−ν2E​(εy​+νεx​)

Result unit MPa

07Elastic strain energy density
u=σ22E=12σ εu = \frac{\sigma^2}{2E} = \frac{1}{2}\sigma\,\varepsilonu=2Eσ2​=21​σε
SymbolDescriptionUnit
uuuStrain energy per unit volumeJ/m³ = Pa

Result unit MPa

Tables

Elastic constants and strengths of shipbuilding materials (design values)

MaterialEEE [MPa]GGG [MPa]ν\nuνYield / proof σy\sigma_yσy​ [MPa]Tensile σu\sigma_uσu​ [MPa]Density [t/m³]
Hull steel grade A/B/D/E206 00079 0000.30235400–5207.85
Hull steel AH32/DH32/EH32206 00079 0000.30315440–5707.85
Hull steel AH36/DH36/EH36206 00079 0000.30355490–6307.85
Hull steel AH40/DH40/EH40206 00079 0000.30390510–6607.85
Aluminium 5083-H116 (unwelded / welded)70 00026 5000.33215 / 125305 / 2752.66
Aluminium 6082-T6 (unwelded / welded)70 00026 5000.33260 / 115310 / 1702.70
Stainless 316L (annealed)193 00077 0000.30≥ 220≥ 5208.0
Duplex 1.4462200 00077 0000.30≥ 450≥ 6507.8
E-glass/polyester laminate (woven roving, ~35 % Vf), in-plane12 000–16 0003 0000.25— (ultimate ≈ 150–250)150–2501.6–1.9
Bolts grade 8.8206 00079 0000.306408007.85
Bolts grade 10.9206 00079 0000.3090010007.85
Source: IACS UR W11 (hull steels); DNV Rules Pt.2 Ch.2 (aluminium alloys, welded values indicative — confirm per temper and thickness); EN 10088 (stainless); ISO 898-1 (bolts); laminate values indicative, see Section 3.5 and ISO 12215-5 Annex C.

Examples

#01

Strain gauge reading on a deck plate

Worked example

Problem

A longitudinal strain gauge on the strength deck of the example vessel reads +420 με+420\ \mu\varepsilon+420 με in a hogging condition; a transverse gauge at the same point reads −95 με-95\ \mu\varepsilon−95 με. Assuming plane stress with negligible shear at the gauge, find the longitudinal and transverse stresses.

Solution

εx=420×10−6\varepsilon_x = 420 \times 10^{-6}εx​=420×10−6, εy=−95×10−6\varepsilon_y = -95 \times 10^{-6}εy​=−95×10−6, E=206 000E = 206\,000E=206000 MPa, ν=0.30\nu = 0.30ν=0.30.

σx=206 0001−0.09 (420−0.30×95)×10−6=226 374×391.5×10−6=88.6 MPa\sigma_x = \frac{206\,000}{1 - 0.09}\,(420 - 0.30 \times 95) \times 10^{-6} = 226\,374 \times 391.5 \times 10^{-6} = 88.6\ \text{MPa}σx​=1−0.09206000​(420−0.30×95)×10−6=226374×391.5×10−6=88.6 MPa σy=226 374×(−95+0.30×420)×10−6=226 374×31×10−6=7.0 MPa\sigma_y = 226\,374 \times (-95 + 0.30 \times 420) \times 10^{-6} = 226\,374 \times 31 \times 10^{-6} = 7.0\ \text{MPa}σy​=226374×(−95+0.30×420)×10−6=226374×31×10−6=7.0 MPa

Note that a uniaxial interpretation (σx=Eεx=86.5\sigma_x = E\varepsilon_x = 86.5σx​=Eεx​=86.5 MPa) would be 2.4 % low and would give a wrong (negative) transverse stress; the transverse gauge reading is largely the Poisson contraction, and the small positive σy\sigma_yσy​ indicates slight transverse restraint. The deck stress of 89 MPa is about 50 % of the IACS permissible hull girder stress 175 MPa for mild steel.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 1 (Tension, compression and shear), Ch. 7.5 (Hooke's law for plane stress)Textbook
Hibbeler, Mechanics of Materials, 10th ed. (2017)Clause Ch. 3 (Mechanical properties of materials), Ch. 10.6 (Material property relationships)Textbook
IACS Unified RequirementsClause UR W11 — Tables of mechanical propertiesMandatory

Free download from iacs.org.uk.

DNV Rules for Classification — ShipsClause Pt.2 Ch.2 (Metallic materials) — Sec. 2 (Rolled steel), Sec. 9 (Aluminium alloys)Mandatory

Confirm edition in force.

NavArch Handbook · Chapter 2 · printed on —