Glossary

66 terms of naval architecture, hydrostatics and stability. Each entry links to the section where the concept is treated.

L

LOA

Length overall: the extreme length of the hull measured between the foremost and aftermost points of the ship, including permanent appendages such as a bulbous bow or a stern overhang.

Section 4.1 · Principal dimensions and definitions
LBP

Length between perpendiculars: the distance measured on the summer load waterline from the forward side of the stem to the after side of the rudder post, or to the centre of the rudder stock where no rudder post is fitted.

Section 4.1 · Principal dimensions and definitions
LWL

Length on the waterline: the length of the hull measured at the waterline of the loading condition considered, from the forward to the after intersection of the hull with that waterline.

Section 4.1 · Principal dimensions and definitions
Lightship

The mass of the ship complete with machinery, equipment and liquids in the machinery to working level, but excluding deadweight items such as cargo, fuel, stores, ballast, crew and passengers.

Section 4.4 · Displacement, volume and Archimedes' principle
Loading condition

A defined distribution of masses on board with the resulting draughts, trim, KG and GZ curve, which must be shown to satisfy the applicable stability criteria.

Section 5.14 · Loading conditions and the stability booklet
List

A sustained transverse inclination caused by an unequal distribution of mass or by negative initial stability, as distinct from the transient heel produced by an external moment.

Section 5.9 · List due to transverse weight shift and added weights
Lost buoyancy method

A damage calculation method in which the flooded compartment is treated as open to the sea, so that the waterplane area and the displaced volume are reduced while the mass of the ship is unchanged.

Section 5.12 · Damage stability fundamentals: lost buoyancy vs added weight, permeability

M

Moulded breadth

The greatest breadth of the hull measured between the inside surfaces of the shell plating, normally at or near midships; it excludes shell thickness and external appendages.

Section 4.1 · Principal dimensions and definitions
Moulded depth

The vertical distance measured at midships from the top of the keel plate to the top of the deck beam at side, on the moulded lines.

Section 4.1 · Principal dimensions and definitions
Midship

The transverse section of the hull at the mid-point of the length between perpendiculars, taken as the reference section for breadth, depth and section modulus.

Section 4.1 · Principal dimensions and definitions
Midship section coefficient

The ratio of the immersed area of the midship section to the area of the circumscribing rectangle of breadth and draught: CM=AM/(B T)C_M = A_M / (B\,T).

Section 4.3 · Form coefficients and typical values
Mass displacement

The mass of the ship and its contents, equal to the mass of the water displaced: Δ=ρ ∇\Delta = \rho\,\nabla.

Section 4.4 · Displacement, volume and Archimedes' principle
Metacentre

The point of intersection of successive verticals through the centre of buoyancy for small angles of heel, taken transversely unless stated otherwise; its height above the keel is KM.

Section 5.1 · Initial stability: metacentre, GM and the righting lever at small angles
Metacentric radius

The distance from the centre of buoyancy to the metacentre, equal to the transverse second moment of the waterplane area divided by the displaced volume: BM=IT/∇BM = I_T / \nabla.

Section 5.1 · Initial stability: metacentre, GM and the righting lever at small angles
Metacentric height

The distance from the centre of gravity to the metacentre, GM=KM−KGGM = KM - KG; a positive value denotes initial stability at small angles of heel.

Section 5.1 · Initial stability: metacentre, GM and the righting lever at small angles
MCT1cm

Moment to change trim one centimetre: the trimming moment required to alter the trim by one centimetre, derived from the longitudinal metacentric height and the displacement.

Section 4.8 · TPC, MCT1cm and hydrostatic curves
Margin line

A line drawn at least 76 mm below the upper surface of the bulkhead deck at side, which no point of the ship is to immerse in the final stage of flooding.

Section 5.12 · Damage stability fundamentals: lost buoyancy vs added weight, permeability

D

Draught

The vertical distance from the keel to the waterline at the point considered; the mean of the forward and after draughts is the mean draught used in hydrostatic calculations.

Section 4.1 · Principal dimensions and definitions
Displacement volume

The volume of water displaced by the hull up to the waterline considered, equal to the integral of the sectional areas along the length: ∇=∫A(x) dx\nabla = \int A(x)\,dx.

Section 4.4 · Displacement, volume and Archimedes' principle
Deadweight

The difference between the displacement at the assigned load line and the lightship mass; it comprises cargo, fuel, fresh water, ballast, stores, crew and passengers.

Section 4.4 · Displacement, volume and Archimedes' principle
Downflooding angle

The least angle of heel at which an unprotected opening that could lead to progressive flooding becomes immersed.

Section 5.6 · IMO 2008 IS Code: general intact stability criteria
Deck-edge immersion

The angle of heel at which the deck edge at side enters the water; it marks the end of the range over which the waterplane area increases with heel.

Section 5.6 · IMO 2008 IS Code: general intact stability criteria
Dynamical stability

The work done in heeling the ship to a given angle, equal to the area under the GZ curve up to that angle and expressed in metre-radians.

Section 5.5 · Dynamic stability and the area under the GZ curve
Dock water allowance

The change in draught when a ship passes between waters of different densities, computed from the displacement and the waterplane area for the density concerned.

Section 4.11 · Effect of water density: FWA and dock water allowance

T

Trim

The difference between the after and forward draughts; the ship is by the stern when the after draught exceeds the forward draught, and by the head in the contrary case.

Section 5.8 · Longitudinal stability and trim
TPC

Tonnes per centimetre immersion: the mass that must be added to change the mean draught by one centimetre, equal to the waterplane area multiplied by the water density.

Section 4.8 · TPC, MCT1cm and hydrostatic curves
Torremolinos Convention

The Torremolinos International Convention for the Safety of Fishing Vessels, 1977, as superseded by its 1993 Protocol; it sets stability and construction requirements for fishing vessels of 24 m length and over.

Section 5.13 · Fishing vessel stability: Torremolinos/Cape Town and NMA requirements

F

Freeboard

The vertical distance measured at side amidships from the waterline to the freeboard deck; the minimum freeboard is assigned in accordance with the applicable load line convention.

Section 10.3 · International Convention on Load Lines 1966/1988: freeboard basics
Fluid GM

The metacentric height corrected for the free surface effect of liquids in slack tanks, obtained by deducting the total free surface moment divided by the displacement from the solid GM.

Section 5.3 · Free surface effect of liquids in tanks
Free surface moment

The moment transferred by a liquid free to move in a slack tank as the ship heels, equal to the second moment of the free surface about its own centroid multiplied by the liquid density.

Section 5.3 · Free surface effect of liquids in tanks
FWA

Fresh water allowance: the increase in draught when a ship passes from seawater of relative density 1.025 to fresh water, equal to Δ/(4 TPC)\Delta / (4\,TPC) in centimetres.

Section 4.11 · Effect of water density: FWA and dock water allowance
Floodable length

The maximum length of a compartment, centred at a given point along the ship, that can be flooded without immersing the margin line.

Section 5.12 · Damage stability fundamentals: lost buoyancy vs added weight, permeability

B

Baseline

The horizontal datum from which vertical dimensions are measured, normally the top of the keel at its lowest point or the moulded base line defined on the lines plan.

Section 4.1 · Principal dimensions and definitions
Block coefficient

The ratio of the displaced volume to the volume of a rectangular block of the same length, breadth and draught: CB=∇/(L B T)C_B = \nabla / (L\,B\,T).

Section 4.3 · Form coefficients and typical values
Bonjean curve

A curve of immersed sectional area plotted against draught for a given station; the set of Bonjean curves gives the displacement and its longitudinal distribution at any trimmed waterline.

Section 4.10 · Bonjean curves and their use
Block reaction

The upward force exerted by the keel blocks on the hull during docking; its magnitude and position determine the virtual loss of metacentric height at the critical instant.

Section 5.11 · Dry-docking and grounding

P

Prismatic coefficient

The ratio of the displaced volume to the volume of the prism formed by the midship section area over the length: CP=∇/(AM L)C_P = \nabla / (A_M\,L).

Section 4.3 · Form coefficients and typical values
Permeability

The proportion of the gross volume of a compartment that can be occupied by water in the event of flooding, expressed as a fraction or a percentage.

Section 5.12 · Damage stability fundamentals: lost buoyancy vs added weight, permeability

W

Waterplane coefficient

The ratio of the waterplane area to the area of the circumscribing rectangle of length and breadth at the waterline: CW=AW/(L B)C_W = A_W / (L\,B).

Section 4.3 · Form coefficients and typical values
Weather criterion

The intact stability criterion of the 2008 IS Code comparing the heeling energy of a steady wind and a superimposed gust with the righting energy available at a defined roll angle.

Section 5.7 · IMO 2008 IS Code: severe wind and rolling (weather) criterion
Wetted surface

The area of the hull in contact with water, including appendages where stated; it is a primary input to the calculation of frictional resistance.

Section 4.9 · Wetted surface area approximations

A

Appendage allowance

An addition to the moulded volume or wetted surface to account for bilge keels, shaft brackets, rudder and other appendages that are not represented on the moulded form.

Section 4.9 · Wetted surface area approximations
Angle of vanishing stability

The angle of heel at which the righting lever falls to zero on the descending branch of the GZ curve; beyond it the ship is unstable without external support.

Section 5.4 · Stability at large angles: GZ curves, cross curves (KN)
Allowable KG curve

A curve of the maximum permissible height of the centre of gravity plotted against displacement, derived from the applicable stability criteria and used to verify a loading condition.

Section 5.4 · Stability at large angles: GZ curves, cross curves (KN)
Angle of loll

The angle at which a ship with a negative initial metacentric height rests in stable equilibrium on either side of the upright, where the righting lever is again zero.

Section 5.9 · List due to transverse weight shift and added weights
Added weight method

A damage calculation method in which the water admitted to the damaged compartment is treated as an added mass at its centre, the external form of the ship remaining intact.

Section 5.12 · Damage stability fundamentals: lost buoyancy vs added weight, permeability

C

Centre of buoyancy

The centroid of the displaced volume; its longitudinal position (LCB) and height above the keel (KB) are hydrostatic particulars of the waterline considered.

Section 4.7 · Hydrostatic particulars: KB, BM, KM, LCB, LCF
Centre of flotation

The centroid of the waterplane area, about which the ship trims for small changes of trim; its longitudinal position is the LCF.

Section 4.7 · Hydrostatic particulars: KB, BM, KM, LCB, LCF
Cross curves (KN)

Curves of the righting lever measured from the keel, plotted against displacement for a series of angles of heel, from which the GZ curve of any loading condition is derived.

Section 5.4 · Stability at large angles: GZ curves, cross curves (KN)
Critical instant

The instant during dry-docking or grounding at which the upthrust at the keel block is just sufficient to reduce the metacentric height to zero, so that the ship becomes unstable about the block.

Section 5.11 · Dry-docking and grounding

R

Righting lever

The horizontal distance from the centre of gravity to the vertical through the centre of buoyancy at a given angle of heel: GZ=KN−KGsin⁡φGZ = KN - KG \sin\varphi.

Section 5.4 · Stability at large angles: GZ curves, cross curves (KN)
Roll-back angle

In the weather criterion, the angle of heel to windward to which the ship is assumed to roll before the gust is applied; it is derived from the roll period and the steady wind heeling lever.

Section 5.7 · IMO 2008 IS Code: severe wind and rolling (weather) criterion

I

Inclining experiment

A test in which known masses are shifted transversely to produce a measurable heel, from which the lightship mass and the height of its centre of gravity are determined.

Section 5.2 · The inclining experiment
Icing allowance

An addition to the mass and vertical centre of gravity to account for ice accretion on exposed surfaces, applied in accordance with the operating area and the applicable stability requirements.

Section 5.7 · IMO 2008 IS Code: severe wind and rolling (weather) criterion
IS Code

The International Code on Intact Stability, 2008 (IMO Res. MSC.267(85)) as amended; Part A is mandatory under SOLAS and the 1988 Load Line Protocol, while Part B is recommendatory.

Section 5.6 · IMO 2008 IS Code: general intact stability criteria
ICLL

The International Convention on Load Lines, 1966, as modified by the 1988 Protocol; it assigns minimum freeboards and defines the conditions of assignment of load lines.

Section 10.3 · International Convention on Load Lines 1966/1988: freeboard basics

S

Sectional area curve

A curve of the immersed area of each transverse section plotted along the length; its integral is the displaced volume and its centroid the longitudinal centre of buoyancy.

Section 4.10 · Bonjean curves and their use
Simpson's rules

A family of numerical integration rules in which ordinates are combined with fixed multipliers and a common interval to evaluate areas, moments and second moments of ship curves.

Section 4.5 · Simpson's rules and numerical integration of ship curves
Stability booklet

The approved document supplied to each ship containing the stability information, hydrostatic data, cross curves, limiting KG or GZ curves and the worked loading conditions required by the Administration.

Section 5.14 · Loading conditions and the stability booklet
Suspended weight

A mass hanging from a point above the centre of gravity; its effective centre of gravity is at the point of suspension, so that the ship's KG rises by the corresponding moment.

Section 5.10 · Heavy-lift operations and suspended weights
SOLAS

The International Convention for the Safety of Life at Sea, 1974, as amended; its chapters set the mandatory subdivision, stability, machinery, fire and life-saving requirements for ships.

Section 10.2 · SOLAS structure and chapters relevant to design

H

Hydrostatic curves

Curves of displacement, TPC, KB, LCB, LCF, KM and MCT plotted against draught for the ship in even keel, used to obtain the particulars of any loading condition.

Section 4.8 · TPC, MCT1cm and hydrostatic curves
Heel

The transverse inclination of a ship produced by an external heeling moment such as wind, a turn or a shifted weight.

Section 5.1 · Initial stability: metacentre, GM and the righting lever at small angles

G

Gross tonnage

The dimensionless measure of the total enclosed volume of a ship determined under the International Convention on Tonnage Measurement of Ships, 1969.

Section 4.12 · Tonnage measurement basics (ITC 1969)

N

Net tonnage

The dimensionless measure of the earning capacity of a ship, derived from the moulded volume of cargo spaces and the number of passengers under the 1969 Tonnage Convention.

Section 4.12 · Tonnage measurement basics (ITC 1969)
Nordic Boat Standard

A regional standard for the design, construction and equipment of recreational and small commercial craft under 15 m, applied alongside the ISO 12217 and ISO 12215 series.

Section 10.9 · Nordic Boat Standard (1990) for vessels under 15 m