Chapter 5 / Section 5.10
Heavy-lift operations and suspended weights
The suspended weight acts at the point of suspension
When a mass is lifted by a crane or derrick, its weight acts at the head of the jib (the point of suspension), not at the hook or at the load. The instant the load leaves the quay (or the deck), the ship's rises as if had been placed at the jib head height :
(if the load was already on board on deck at , the virtual rise is at constant displacement.)
Consequences
- Reduction of GM — can be large for a high jib and a small ship. with at the new displacement.
- Heeling moment from the outreach of the jib head: . List ; with the reduced the list can become excessive — anti-heeling ballast is transferred in parallel with the slew.
- Trim from the longitudinal position of the jib head.
- Dynamic effects — load swinging, crane motion and vessel motion: class rules apply a dynamic factor to the hook load for the crane structure; for stability the IS Code Part B Ch. 2.9 defines the heeling moment with the load at the maximum outreach.
IS Code 2008 Part B, Ch. 2.9 — Lifting operations (summary)
Applies to ships engaged in lifting where the lift causes a significant heel (criterion in 2.9.1). Two alternative approaches are given:
- 2.9.2 — Residual GZ criteria: with the lifting heeling lever, the equilibrium heel shall not exceed limits set by the Administration, the residual righting lever area shall be adequate, and the residual freeboard/ downflooding limits are respected; the Code gives the methodology and leaves some limit values to the Administration. DNV implements this in Pt.3 Ch.15 / Pt.5 for crane vessels and OSV with crane notation.
- 2.9.3 — Simplified criteria for non-counter-ballasted ships: the residual metacentric height, taking into account the lift, shall be positive and the equilibrium heel limited. A sudden loss of the load (hook failure) makes the ship roll to the opposite side; the Code requires that the ship survive this: the area under the GZ curve with the load dropped must exceed that for the load held (energy balance), and the counter-ballast remaining on board must not produce an excessive heel.
Operational practice
- Press up or empty slack tanks before the lift; pre-ballast to the low side opposite to the expected list; limit the jib height; lift at minimum outreach; use the loading computer's "crane mode".
Formulas
| Symbol | Description | Unit |
|---|---|---|
| Mass of the lifted load | t | |
| Height of the point of suspension (jib head) above baseline | m | |
| Displacement and KG before the lift | t, m |
Result unit m
| Symbol | Description | Unit |
|---|---|---|
| Height of the load before lifting | m |
Result unit m
| Symbol | Description | Unit |
|---|---|---|
| Transverse outreach of the jib head from centreline | m | |
| Metacentric height with the suspended load | m |
Result unit deg
| Symbol | Description | Unit |
|---|---|---|
| Anti-heeling ballast mass and its transverse position (opposite side) | t, m |
Result unit t·m
Tables
Lifting operations — typical limits applied by Administrations and class (indicative)
| Quantity | Typical limit | Source |
|---|---|---|
| Heel during lift (with counter-ballast) | ≤ 5°–10° (often 5° in operation manuals) | IS Code Part B 2.9; DNV crane vessel notations |
| Residual GM with load suspended | > 0 (simplified) / usually ≥ 0.15–0.5 m per operator | IS Code Part B 2.9.3; operator procedures |
| Heel after sudden load loss | ≤ 15° or deck-edge immersion / downflooding | IS Code Part B 2.9.2 |
| Freeboard at the low side | Not less than a stated minimum (e.g. 0.5 m to the deck edge) | Administration / operator |
| Dynamic hook load factor for structure | 1.1–1.3 (harbour/offshore) depending on crane class | DNV-ST-0378 Sec. 4 |
Examples
GM and heel during a heavy lift
Worked example
Problem
Example vessel: t, m. The deck crane lifts an 80 t item from the quay with the jib head at m above baseline and an outreach m. at 6394 t is 5.95 m. Find during the lift and the heel without counter-ballast; then the counter-ballast required at 6.5 m off centreline to limit heel to 3°.
References
Mandatory where the Administration applies Part B to the ship type.
For the crane structure and foundation; stability is governed by Pt.3 Ch.15 and the IS Code.
Version 2 · last updated 19 Nov 2026 · Editor