NavArchHandbook0 ch

No chapters yet.

Engineering tools
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›4. Ship Geometry & Hydrostatics›4.8 TPC, MCT1cm and hydrostatic curves

Chapter 4 / Section 4.8

TPC, MCT1cm and hydrostatic curves

Print this section

Tonnes per centimetre immersion, TPC

Mass that changes the mean draught by 1 cm at a given waterline. Because the added layer is 0.01 m thick, TPC=ρAWP/100TPC = \rho A_{WP}/100TPC=ρAWP​/100 with AWPA_{WP}AWP​ in m² and ρ\rhoρ in t/m³. In fresh water multiply the seawater TPC by 1.000/1.0251.000/1.0251.000/1.025.

Moment to change trim by one centimetre, MCT1cm (also MTC)

Trimming moment (t·m) required to change the trim by 1 cm. Derived from longitudinal stability: a moment MMM produces an angle of trim θ\thetaθ with M=Δ GMLtan⁡θM = \Delta\,GM_L \tan\thetaM=ΔGML​tanθ and trim t=Ltan⁡θt = L\tan\thetat=Ltanθ; setting t=0.01t = 0.01t=0.01 m gives MCT1cm=Δ GML/(100 L)MCT1cm = \Delta\,GM_L/(100\,L)MCT1cm=ΔGML​/(100L). Because GML≈BMLGM_L \approx BM_LGML​≈BML​ (the difference KB−KGKB - KGKB−KG is negligible compared with BMLBM_LBML​), the hydrostatic curves give MCT1cm≈Δ BML/(100 L)=ρIL/(100L)MCT1cm \approx \Delta\,BM_L/(100\,L) = \rho I_L/(100 L)MCT1cm≈ΔBML​/(100L)=ρIL​/(100L), which depends only on geometry.

The hydrostatic curves (hydrostatic table)

Plotted against mean draught (level keel, sometimes also for several trims):

  • Displacement Δ\DeltaΔ (seawater, and sometimes fresh water)
  • KBKBKB, KMTKM_TKMT​ (and BMTBM_TBMT​), KMLKM_LKML​ (or BMLBM_LBML​)
  • LCBLCBLCB and LCFLCFLCF from midship or AP
  • AWPA_{WP}AWP​, TPCTPCTPC, MCT1cmMCT1cmMCT1cm
  • CBC_BCB​, CPC_PCP​, CMC_MCM​, CWPC_{WP}CWP​
  • Wetted surface SSS Modern practice gives them as a table at draught intervals (e.g. 0.1 m) in the stability booklet, computed by the hydrostatics software. The engineer must still be able to check an entry by hand.

Change of mean draught for a small added mass

δT [cm]=wTPC\delta T\,[\text{cm}] = \frac{w}{TPC}δT[cm]=TPCw​

Valid while TPCTPCTPC is nearly constant (small www; use the mean TPC between the two waterlines for larger changes).

Formulas

01Tonnes per centimetre immersion
TPC=ρ AWP100TPC = \frac{\rho\, A_{WP}}{100}TPC=100ρAWP​​
SymbolDescriptionUnit
TPCTPCTPCTonnes per centimetre immersiont/cm
ρ\rhoρWater densityt/m^3
AWPA_{WP}AWP​Waterplane aream^2

Result unit t/cm

02Moment to change trim by one centimetre
MCT1cm=Δ GML100 L≈Δ BML100 L=ρ IL100 LMCT1cm = \frac{\Delta\, GM_L}{100\, L} \approx \frac{\Delta\, BM_L}{100\, L} = \frac{\rho\, I_L}{100\, L}MCT1cm=100LΔGML​​≈100LΔBML​​=100LρIL​​
SymbolDescriptionUnit
MCT1cmMCT1cmMCT1cmMoment to change trim 1 cmt·m/cm
Δ\DeltaΔDisplacementt
GMLGM_LGML​Longitudinal metacentric heightm
LLLLength between perpendiculars (the length over which trim is measured)m

Result unit t·m/cm

03Sinkage from an added mass
δT=wTPC\delta T = \frac{w}{TPC}δT=TPCw​
SymbolDescriptionUnit
δT\delta TδTChange of mean draught (bodily sinkage)cm
wwwAdded (or removed, negative) masst

Result unit cm

04Approximate MCT1cm (merchant ships)
MCT1cm≈7.8 (TPC)2BMCT1cm \approx \frac{7.8\, (TPC)^2}{B}MCT1cm≈B7.8(TPC)2​
SymbolDescriptionUnit
BBBBreadthm

Result unit t·m/cm

Empirical rule of thumb (Barrass & Derrett); accuracy about ±10 %. For checking only.

Tables

Hydrostatic table excerpt for the 100 m example vessel (level keel, seawater) — illustrative

TTT [m]Δ\DeltaΔ [t]KBKBKB [m]KMTKM_TKMT​ [m]LCBLCBLCB [m fwd ⊗]LCFLCFLCF [m fwd ⊗]TPCTPCTPC [t/cm]MCT1cmMCT1cmMCT1cm [t·m/cm]
4.5050802.336.21+0.95+1.1011.6054.0
5.0056902.586.08+0.80+1.0011.8557.0
5.5063142.845.98+0.60+0.8812.0559.8
6.0069503.105.92+0.40+0.7012.2562.5
Source: Illustrative values consistent with the worked examples of this chapter (C_B = 0.70, B = 16 m). Not a real vessel.

Observe the typical trends: KM_T decreases with draught while KB increases; LCB and LCF move aft as the fuller aft waterlines immerse.

Examples

#01

MCT1cm for the example vessel

Worked example

Problem

Δ=6314\Delta = 6314Δ=6314 t, GML≈BML+KB−KG=97.1+2.84−5.21=94.7GM_L \approx BM_L + KB - KG = 97.1 + 2.84 - 5.21 = 94.7GML​≈BML​+KB−KG=97.1+2.84−5.21=94.7 m, LBP=100L_{BP} = 100LBP​=100 m. Find MCT1cmMCT1cmMCT1cm and check with the rule of thumb using TPC=12.05TPC = 12.05TPC=12.05 t/cm and B=16B = 16B=16 m.

Solution

MCT1cm=6314×94.7100×100=59.8 t⋅m/cmMCT1cm = \frac{6314 \times 94.7}{100 \times 100} = 59.8\ \text{t·m/cm}MCT1cm=100×1006314×94.7​=59.8 t⋅m/cm

Rule of thumb: 7.8×12.052/16=7.8×145.2/16=70.87.8 \times 12.05^2 / 16 = 7.8 \times 145.2 / 16 = 70.87.8×12.052/16=7.8×145.2/16=70.8 t·m/cm — about 18 % higher. The rule of thumb was derived for conventional merchant forms with CWPC_{WP}CWP​ around 0.80–0.85; for this fuller-aft, finer-forward PSV form it overestimates. Use the calculated value.

References

Barrass & Derrett (2012)Clause Ch. 11 (TPC), Ch. 22 (Trim — MCTC)Textbook
IMO IS Code 2008Clause Part B, Ch. 3.6 (Stability booklet — hydrostatic data to be included)Recommended

Part B is recommendatory unless made mandatory by the Administration; the Administration usually requires the hydrostatic table in the approved stability booklet.

Previous · 4.7Hydrostatic particulars: KB, BM, KM, LCB, LCFNext · 4.9Wetted surface area approximations

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Tonnes per centimetre immersion, TPC
  • Moment to change trim by one centimetre, MCT1cm (also MTC)
  • The hydrostatic curves (hydrostatic table)
  • Change of mean draught for a small added mass
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Barrass & Derrett (2012)

    Ch. 11 (TPC), Ch. 22 (Trim — MCTC)

  • IMO IS Code 2008

    Part B, Ch. 3.6 (Stability booklet — hydrostatic data to be included)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.