NavArchHandbook0 ch

No chapters yet.

Engineering tools
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›4. Ship Geometry & Hydrostatics›4.10 Bonjean curves and their use

Chapter 4 / Section 4.10

Bonjean curves and their use

Print this section

Definition

A Bonjean curve is the plot, for one station, of the immersed cross-sectional area A(z)A(z)A(z) against height zzz above the baseline. Drawn for every station on the profile of the ship, the set of curves lets the engineer read the sectional area at any waterline — level, trimmed, or a wave profile — simply by intersecting the waterline with each curve.

Construction

For each station, the area up to each waterline is obtained by Simpson integration of the half-breadths over height (Section 4.6), doubled. Often the vertical moment of area about the baseline is drawn as a second curve on the same axes.

Uses

  1. Displacement and LCB at a trimmed waterline — draw the trimmed waterline on the profile, read AiA_iAi​ at each station, integrate longitudinally with Simpson's rule: ∇=∫A(x) dx\nabla = \int A(x)\,dx∇=∫A(x)dx, LCB=∫xA dx/∇LCB = \int xA\,dx/\nablaLCB=∫xAdx/∇.
  2. Launching calculations — buoyancy and its centroid at successive positions of the hull on the ways.
  3. Longitudinal strength — buoyancy distribution on a static wave (hogging/sagging) for the still-water and wave bending moment.
  4. Damage stability and flooding — volume and centroid of a flooded compartment between two stations up to any waterline.
  5. Grounding and docking — buoyancy lost as the waterline changes.

Practical notes

  • Use enough waterlines near the baseline and near the deck where the section shape changes fast.
  • With modern software the Bonjean curves are implicit in the hull model; nevertheless the stability booklet for some flag states still includes them, and a hand check of one trimmed displacement from Bonjean areas is a standard verification step.

Formulas

01Sectional area to height z (Bonjean ordinate)
A(z)=2∫0zy(ζ) dζA(z) = 2\int_0^{z} y(\zeta)\,d\zetaA(z)=2∫0z​y(ζ)dζ
SymbolDescriptionUnit
A(z)A(z)A(z)Immersed area of the station up to height zm^2
y(ζ)y(\zeta)y(ζ)Half-breadth of the station at height ζm

Result unit m^2

02Displacement at an arbitrary (trimmed) waterline
∇=∫0LA(x,zWL(x)) dx\nabla = \int_0^{L} A\big(x, z_{WL}(x)\big)\,dx∇=∫0L​A(x,zWL​(x))dx
SymbolDescriptionUnit
zWL(x)z_{WL}(x)zWL​(x)Height of the waterline at station x (linear for trim; sinusoidal/trochoidal for a wave)m

Result unit m^3

Examples

#01

Trimmed displacement from Bonjean areas

Worked example

Problem

A 60 m vessel (stations every 6 m, 0 = AP to 10 = FP) floats at TA=4.20T_A = 4.20TA​=4.20 m and TF=3.60T_F = 3.60TF​=3.60 m. Bonjean areas read at the trimmed waterline are [m²]: 2.1, 14.8, 26.5, 34.9, 39.6, 40.8, 39.2, 33.5, 23.0, 10.4, 1.2. Find the displacement volume and LCB from midship.

Solution

Simpson's first rule, h=6h = 6h=6 m:

StnAAASMA⋅SMA\cdot SMA⋅SMLeverProduct × lever
02.112.1−5−10.5
114.8459.2−4−236.8
226.5253.0−3−159.0
334.94139.6−2−279.2
439.6279.2−1−79.2
540.84163.200.0
639.2278.4+178.4
733.54134.0+2268.0
823.0246.0+3138.0
910.4441.6+4166.4
101.211.2+56.0
Σ797.5−107.9
∇=63×797.5=1595 m3,ΔSW=1.025×1595=1635 t\nabla = \frac{6}{3} \times 797.5 = 1595\ \text{m}^3, \qquad \Delta_{SW} = 1.025 \times 1595 = 1635\ \text{t}∇=36​×797.5=1595 m3,ΔSW​=1.025×1595=1635 t LCB=6×−107.9797.5=−0.81 m(0.81 m aft of midship)LCB = 6 \times \frac{-107.9}{797.5} = -0.81\ \text{m} \quad (0.81\ \text{m aft of midship})LCB=6×797.5−107.9​=−0.81 m(0.81 m aft of midship)

The LCB is aft of midship, as expected for a vessel trimmed by the stern.

References

Rawson & Tupper (2001)Clause Vol. 1, Ch. 3 (Bonjean curves) and Ch. 6 (Launching)Textbook
PNA Vol. I (1988)Clause Ch. 1, Sec. 7 (Bonjean curves)Textbook
Previous · 4.9Wetted surface area approximationsNext · 4.11Effect of water density: FWA and dock water allowance

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Definition
  • Construction
  • Uses
  • Practical notes
  • Formulas
  • Examples
  • References

Applicable standards

  • Rawson & Tupper (2001)

    Vol. 1, Ch. 3 (Bonjean curves) and Ch. 6 (Launching)

  • PNA Vol. I (1988)

    Ch. 1, Sec. 7 (Bonjean curves)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.