NavArchHandbook0 ch

No chapters yet.

Engineering tools
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›4. Ship Geometry & Hydrostatics›4.3 Form coefficients and typical values

Chapter 4 / Section 4.3

Form coefficients and typical values

Print this section

Form coefficients are dimensionless ratios that describe the fullness of the hull. They are defined at a stated waterline — usually the design waterline — and must always be quoted with the length used (LBPL_{BP}LBP​ or LWLL_{WL}LWL​).

Definitions

  • Block coefficient CBC_BCB​ — ratio of the displacement volume to the circumscribing block L⋅B⋅TL \cdot B \cdot TL⋅B⋅T.
  • Midship section coefficient CMC_MCM​ — ratio of the immersed midship section area AMA_MAM​ to the rectangle B⋅TB \cdot TB⋅T.
  • Prismatic coefficient CPC_PCP​ — ratio of the displacement volume to the prism AM⋅LA_M \cdot LAM​⋅L. It measures the longitudinal distribution of volume and is the primary parameter in resistance work. CP=CB/CMC_P = C_B / C_MCP​=CB​/CM​.
  • Waterplane coefficient CWPC_{WP}CWP​ — ratio of the waterplane area AWPA_{WP}AWP​ to the rectangle L⋅BL \cdot BL⋅B. Governs TPCTPCTPC, BMTBM_TBMT​ and BMLBM_LBML​.
  • Vertical prismatic coefficient CVPC_{VP}CVP​ — ratio of the displacement volume to AWP⋅TA_{WP} \cdot TAWP​⋅T. CVP=CB/CWPC_{VP} = C_B / C_{WP}CVP​=CB​/CWP​.

Interrelations

CB=CP CM=CVP CWPC_B = C_P \, C_M = C_{VP} \, C_{WP}CB​=CP​CM​=CVP​CWP​

Use in early design

  • CBC_BCB​ is selected from speed–length ratio or Froude number (e.g. the Alexander / Watson type formulas) and fixes the displacement for given L,B,TL, B, TL,B,T.
  • CMC_MCM​ is high (0.97–0.995) for full ships with small bilge radius, lower (0.75–0.90) for fine, round-bilge fishing or naval forms.
  • CWPC_{WP}CWP​ relates to CPC_PCP​ approximately as CWP≈(1+2CB)/3C_{WP} \approx (1 + 2C_B)/3CWP​≈(1+2CB​)/3 for U-shaped sections (Schneekluth) — only a first estimate.
  • Sectional area curve: the plot of immersed section area A(x)A(x)A(x) against length; its area is ∇\nabla∇ and its centroid is LCBLCBLCB. Its shape (entrance, parallel body, run) is set by CPC_PCP​ and LCBLCBLCB.

Longitudinal centre of buoyancy, LCBLCBLCB

Usually expressed as a percentage of LBPL_{BP}LBP​ forward (+) or aft (−) of midship. Full slow ships: LCBLCBLCB 1–3 % forward; fast fine ships: 1–3 % aft of midship.

Formulas

01Block coefficient
CB=∇L B TC_B = \frac{\nabla}{L \, B \, T}CB​=LBT∇​
SymbolDescriptionUnit
CBC_BCB​Block coefficient-
∇\nabla∇Moulded displacement volumem^3
LLLLength (state L_{BP} or L_{WL})m
BBBMoulded breadth at waterlinem
TTTDraughtm

Result unit -

02Midship section coefficient
CM=AMB TC_M = \frac{A_M}{B \, T}CM​=BTAM​​
SymbolDescriptionUnit
CMC_MCM​Midship section coefficient-
AMA_MAM​Immersed area of the midship sectionm^2

Result unit -

03Prismatic coefficient
CP=∇AM L=CBCMC_P = \frac{\nabla}{A_M \, L} = \frac{C_B}{C_M}CP​=AM​L∇​=CM​CB​​
SymbolDescriptionUnit
CPC_PCP​Longitudinal prismatic coefficient-

Result unit -

04Waterplane coefficient
CWP=AWPL BC_{WP} = \frac{A_{WP}}{L \, B}CWP​=LBAWP​​
SymbolDescriptionUnit
CWPC_{WP}CWP​Waterplane area coefficient-
AWPA_{WP}AWP​Waterplane aream^2

Result unit -

05Vertical prismatic coefficient
CVP=∇AWP T=CBCWPC_{VP} = \frac{\nabla}{A_{WP} \, T} = \frac{C_B}{C_{WP}}CVP​=AWP​T∇​=CWP​CB​​
SymbolDescriptionUnit
CVPC_{VP}CVP​Vertical prismatic coefficient-

Result unit -

06First estimate of midship coefficient from bilge radius
CM=1−(4−π) r22 B TC_M = 1 - \frac{(4-\pi)\, r^2}{2\, B\, T}CM​=1−2BT(4−π)r2​
SymbolDescriptionUnit
rrrBilge radiusm

Result unit -

Valid for a rectangular section with circular bilge, no rise of floor, no deadrise.

Tables

Typical ranges of form coefficients by ship type (design waterline)

Ship typeCBC_BCB​CPC_PCP​CMC_MCM​CWPC_{WP}CWP​Fn (typical)
Crude oil tanker / bulk carrier0.80–0.860.81–0.870.98–0.9950.87–0.920.14–0.17
General cargo ship0.65–0.750.68–0.770.96–0.9850.78–0.850.18–0.24
Container ship (Panamax)0.58–0.680.60–0.700.97–0.9850.75–0.820.22–0.28
Offshore supply vessel / PSV0.68–0.780.72–0.800.93–0.980.82–0.900.20–0.30
Stern trawler / fishing vessel0.50–0.620.58–0.680.80–0.920.75–0.850.28–0.38
Tug0.50–0.600.60–0.700.80–0.900.78–0.860.30–0.40
Frigate / fast displacement craft0.45–0.550.58–0.650.75–0.820.70–0.780.35–0.45
Ro-ro / car ferry0.55–0.650.60–0.700.90–0.970.78–0.860.25–0.32
Source: Compiled from Schneekluth & Bertram (1998) Ch. 1 and Watson (1998) Ch. 3; PNA Vol. I (1988) Ch. 1. Ranges are indicative for first estimates.

Watson–Gilfillan type guidance for CBC_BCB​ vs Froude number (single-screw merchant forms)

Fn=V/gLF_n = V/\sqrt{gL}Fn​=V/gL​Indicative CBC_BCB​
0.140.84
0.160.80
0.180.76
0.200.72
0.220.68
0.240.64
0.260.60
0.280.56
Source: Smoothed from the Watson & Gilfillan (1977) recommended line as reproduced in Watson, Practical Ship Design (1998) Fig. 3.7. For guidance only; fishing and offshore forms deviate.

Examples

#01

Form coefficients of a 100 m offshore vessel

Worked example

Problem

A vessel has LBP=100.0L_{BP} = 100.0LBP​=100.0 m, B=16.0B = 16.0B=16.0 m, T=5.50T = 5.50T=5.50 m, moulded displacement volume ∇=6160\nabla = 6160∇=6160 m³, immersed midship area AM=85.4A_M = 85.4AM​=85.4 m² and waterplane area AWP=1176A_{WP} = 1176AWP​=1176 m². Determine CBC_BCB​, CMC_MCM​, CPC_PCP​, CWPC_{WP}CWP​ and CVPC_{VP}CVP​.

Solution

CB=6160100×16×5.5=61608800=0.700C_B = \frac{6160}{100 \times 16 \times 5.5} = \frac{6160}{8800} = 0.700CB​=100×16×5.56160​=88006160​=0.700 CM=85.416×5.5=85.488.0=0.970C_M = \frac{85.4}{16 \times 5.5} = \frac{85.4}{88.0} = 0.970CM​=16×5.585.4​=88.085.4​=0.970 CP=CBCM=0.7000.970=0.722(check: 616085.4×100=0.721)C_P = \frac{C_B}{C_M} = \frac{0.700}{0.970} = 0.722 \quad \left(\text{check: } \frac{6160}{85.4 \times 100} = 0.721\right)CP​=CM​CB​​=0.9700.700​=0.722(check: 85.4×1006160​=0.721) CWP=1176100×16=0.735C_{WP} = \frac{1176}{100 \times 16} = 0.735CWP​=100×161176​=0.735 CVP=CBCWP=0.7000.735=0.952C_{VP} = \frac{C_B}{C_{WP}} = \frac{0.700}{0.735} = 0.952CVP​=CWP​CB​​=0.7350.700​=0.952

All values fall within the PSV range of the table above. The relatively high CVPC_{VP}CVP​ indicates U-shaped sections, typical for a vessel designed for deck cargo and stability.

References

PNA — Principles of Naval Architecture, Vol. I: Stability and Strength (SNAME, 1988)Clause Ch. 1, Sec. 3 (Coefficients of form)Textbook
Schneekluth & Bertram, Ship Design for Efficiency and Economy, 2nd ed. (1998)Clause Ch. 1.5–1.6 (Block coefficient, midship section, waterplane)Textbook

Source of the empirical relations between coefficients.

Previous · 4.2Lines plan, body plan and offsetsNext · 4.4Displacement, volume and Archimedes' principle

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Definitions
  • Interrelations
  • Use in early design
  • Longitudinal centre of buoyancy, LCB
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • PNA — Principles of Naval Architecture, Vol. I: Stability and Strength (SNAME, 1988)

    Ch. 1, Sec. 3 (Coefficients of form)

  • Schneekluth & Bertram, Ship Design for Efficiency and Economy, 2nd ed. (1998)

    Ch. 1.5–1.6 (Block coefficient, midship section, waterplane)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.