Index of symbols

241 symbols defined in the handbook's formulas, each with its description, unit and the sections where it is used. Latin symbols are listed first, then Greek.

241 symbols

  • (x,y)(x, y)

    Position of the point of application relative to O

    m|1.7
  • AA

    Cross-sectional area

    mm²|2.12.2

    Generating area

    m²|1.5

    Area under the curve

    (unit of y) × m|1.3

    Projected lateral area above waterline (hull, superstructure, deck cargo)

    m²|5.7

    Area under the curve

    m² (or as per ordinates)|4.5
  • aa

    Long side

    mm|2.9

    Throat thickness (≈ 0.7 × leg length)

    mm|2.2

    Width at the top

    m|1.5

    Intercept

    unit y|1.6
  • A(x)A(x)

    Cross-sectional area at x

    m²|1.5

    Immersed cross-sectional area at longitudinal position x

    m²|4.4
  • A(z)A(z)

    Immersed area of the station up to height z

    m²|4.10
  • ABTA_{BT}

    Transverse sectional area of bulbous bow at FP (0 if none)

    m²|4.9
  • AiA_i

    Area of element i (plate flange, web, face plate)

    mm²|2.5

    Area of part i

    m²|1.4
  • AMA_M

    Immersed area of the midship section

    m²|4.3
  • AmA_m

    Area enclosed by the wall mid-line

    mm²|2.7
  • AsA_s

    Tensile stress area (M16: 157, M20: 245, M24: 353, M30: 561)

    mm²|2.2
  • ashella_{\text{shell}}

    Shell plating allowance (steel: 0.005–0.008)

    -|4.2
  • AWPA_{WP}

    Intact waterplane area before damage

    m²|5.12

    Waterplane area

    Waterplane area at draught T

    m²|4.7
  • AWP(z)A_{WP}(z)

    Waterplane area at height z above baseline

    m²|4.4
  • BB

    Breadth

    Moulded breadth at waterline

    m|4.3
  • bb

    Plate width perpendicular to the compression (stiffener spacing)

    mm|2.10

    Short span (stiffener spacing)

    mm|2.9

    Sum of half-spacings to adjacent girders

    m|2.5

    Fitted slope

    -|1.8

    Width at the bottom

    m|1.5

    Slope

    (unit y)/(unit x)|1.6

    Tank breadth (across the ship)

    m|5.3
  • b−ab-a

    Length of the integration range

    m|1.3
  • b(x)b(x)

    Buoyancy per unit length (ρ g A(x))

    kN/m|2.3
  • b(z)b(z)

    Width of the section at z

    mm|2.4
  • aˉ\bar a

    S–N curve intercept (category and environment dependent)

    MPa^m|2.11
  • rˉ\bar r

    Distance of the centroid of the generating area from the axis

    m|1.5
  • xˉ\bar x

    Centroid position along x

    m|1.5
  • zˉ\bar z

    Centroid coordinate

    m|1.4
  • zˉi\bar z_i

    Centroid of part i

  • bi,hib_i, h_i

    Width and height (in the bending direction) of rectangular element i

    mm|2.5
  • bi,tib_i, t_i

    Length and thickness of each flat element

    mm|2.7
  • BMBM

    Transverse metacentric radius

    m|5.1
  • BMTBM_T

    Transverse metacentric radius

    m|4.7
  • CC

    Roll coefficient (≈ 0.40; IS Code formula in 5.7)

    -|5.1
  • CBC_B

    Block coefficient

    -|4.3
  • CB,CM,CWPC_B, C_M, C_{WP}

    Form coefficients on L_WL

    -|4.9
  • cic_i

    Tchebycheff spacing coefficients (table)

    -|1.3
  • CMC_M

    Midship section coefficient

    -|4.3
  • CPC_P

    Longitudinal prismatic coefficient

    -|4.3
  • CSC_S

    Wetted surface coefficient (2.5–2.7 merchant; up to 2.9 fine forms)

    -|4.9
  • CVPC_{VP}

    Vertical prismatic coefficient

    -|4.3
  • CWPC_{WP}

    Waterplane area coefficient

    -|4.3
  • DD

    Flexural rigidity per unit width

    N·mm|2.9

    Moulded depth amidships

    Moulded depth

    m|4.1
  • dd

    Bolt/pin diameter

    mm|2.2

    Distance between the two parallel axes

    m|1.4

    Transverse distance shifted

    m|5.9

    Mean moulded draught

    m|5.7

    Mean draught

    m|5.4

    Transverse distance moved (centre to centre)

    m|5.2

    Moulded draught at summer load line (or 75 % of D for ships without load line)

  • DFFDFF

    Design fatigue factor (1–3 typical; up to 10 for non-inspectable critical offshore details)

  • did_i

    Inner diameter (0 for solid)

    mm|2.7
  • DWADWA

    Dock water allowance

    mm|4.11
  • DWTDWT

    Deadweight

    t|4.1
  • EE

    Young's modulus (steel 206 000)

    MPa|2.1

    Work done to heel the ship to angle φ

    kN·m (= kJ)|5.5
  • ee

    Eccentricity of P from the bolt-group centroid

    mm|2.2
  • EIEI

    Flexural rigidity

    N·mm²|2.6
  • ℓ\ell

    Span between supports

    m|2.3

    Length of the prism

    m|1.5

    Longitudinal distance shifted

    m|5.8
  • ℓg\ell_g

    Girder span between supports

    m|2.5
  • ℓi\ell_i

    Lever of station i from midship in units of h

    -|4.6
  • ℓeff\ell_{\text{eff}}

    Effective weld length

    mm|2.2
  • FF

    Magnitude of the force

    kN|1.7
  • ff

    Freeboard to the deck edge

    m|1.7

    Moulded freeboard at side amidships

    m|4.1
  • F(x)F(x)

    Maximum compartment length centred at x that can be flooded without immersing the margin line

  • FBF_B

    Buoyancy force

    kN|4.4
  • fnf_n

    Natural frequency

    Hz|2.6
  • FSMFSM

    Free surface moment

    t·m|5.3
  • FSMkFSM_k

    Free surface moment of each slack tank

    t·m|5.14
  • fubf_{ub}

    Ultimate tensile strength of the bolt (8.8: 800)

    MPa|2.2
  • FwF_w

    Transverse component of the warp tension (often taken as the bollard pull or a fraction of it)

    kN|5.13
  • FWAFWA

    Fresh water allowance

    mm|4.11
  • GG

    Shear modulus (steel 79 000)

    MPa|2.72.1
  • gg

    Standard gravity 9.80665 (use 9.81)

    m/s²|1.1

    9.81

    m/s²|5.75.1

    Gravitational acceleration (9.81)

    m/s²|4.4
  • GGFSGG_{FS}

    Free surface correction of slack tanks present during the test. The pendulum measures the fluid GM; solid GM = fluid GM + GG_FS and solid KG = KM − solid GM.

    m|5.2
  • GGhGG_h

    Transverse offset of G

    m|5.9
  • GGvGG_v

    Virtual rise of the centre of gravity

    m|5.3
  • GM′GM'

    Metacentric height with the suspended load

  • GMGM

    Fluid metacentric height

    Transverse metacentric height

    m|5.1
  • GM0GM_0

    Initial metacentric height corrected for free surface effects

    m|5.6
  • GMfGM_f

    Fluid (effective) metacentric height

    m|5.3
  • GMLGM_L

    Longitudinal metacentric height

    m|4.8
  • GTGT

    Gross tonnage

  • GZGZ

    Righting lever

    m|5.1
  • GZφGZ_{\varphi}

    Righting lever at heel φ

    m|5.5
  • HH

    Height of the point of suspension (jib head) above baseline

  • hh

    Total depth from the reference line to the top of the face plate

    mm|2.5

    Spacing of the arguments

    as given|1.6

    Height

    m|1.5

    Common interval

    m|1.3

    Head (depth below free surface)

    m|1.1

    Vertical distance moved

    m|5.1

    Common interval between ordinates

    m|4.5
  • hwh_w

    Web height

    mm|2.4
  • II

    Second moment of area about the neutral axis

    mm⁴|2.4
  • ii

    Second moment of the free surface area about its centroidal longitudinal axis

    m⁴|5.3
  • I1∗I_1^{*}

    Second moment of the material-1 area (untransformed) about the common neutral axis

    mm⁴|2.4
  • IxˉI_{\bar x}

    Second moment about the centroidal axis

    m⁴|1.4
  • IBLI_{BL}

    Second moment about the reference (base) line

    m⁴|1.4
  • ILI_L

    Second moment of waterplane about transverse axis through LCF

    m⁴|4.7

    Longitudinal second moment about the transverse axis through the centre of flotation

    m⁴|4.6
  • ITI_T

    Second moment of waterplane area about centreline

    m⁴|4.7

    Transverse second moment of area of the waterplane

    m⁴|4.6
  • IxI_x

    Second moment about the x-axis

    m⁴|1.4
  • IxzI_{xz}

    Product of inertia

    m⁴|1.4
  • JJ

    Polar second moment of area

    mm⁴|2.7
  • KK

    Effective length factor

  • kk

    Material factor

    Thickness exponent (0 for B1/B2; 0.20 for D, E; 0.25 for F–W)

    Buckling coefficient (4.0 for long simply supported plate loaded along a)

    Stiffness

    N/m|2.6

    Bilge/keel factor (1.0 round bilge, 0.7 sharp bilge, table for bilge keels)

    -|5.7
  • K2K_2

    0.2 + 0.02 log10(Vc)

  • K3K_3

    1.25 (GT + 10000)/10000

  • KBKB

    Height of centre of buoyancy

    m|4.7

    Height of centre of buoyancy above baseline

    m|4.6
  • KGKG

    Height of centre of gravity (fluid, i.e. including free surface correction)

    m|5.4

    Height of centre of gravity

    m|5.1
  • KgKg

    Height of the load before lifting

    Height of the centre of gravity of the added mass

    m|5.1
  • KgiKg_i

    Height of its centre of gravity

  • KgvKg_v

    Height of the centroid of the flood water

  • kik_i

    Axial stiffness of member i

    N/mm|2.2
  • KMKM

    Height of metacentre at the reduced displacement Δ − P

    Height of transverse metacentre (from hydrostatics)

    m|5.1
  • KM′KM'

    KM at the new displacement

    m|5.9
  • KMTKM_T

    Height of transverse metacentre above baseline

    m|4.7
  • KNKN

    Cross-curve lever (keel to vertical through heeled B)

    m|5.4
  • kxxk_{xx}

    Transverse radius of gyration (≈ 0.35–0.45 B)

    m|5.1
  • LL

    Unsupported length

    mm|2.10

    Length

    Span

    mm|2.6

    Original length

    mm|2.1

    Total length of the range

    m|1.3

    Length of the vessel

    Length between perpendiculars

    m|5.8

    Length on waterline (or L_BP)

    m|4.9

    Length between perpendiculars (the length over which trim is measured)

    m|4.8

    Length (state L_{BP} or L_{WL})

    m|4.3
  • ll

    Distance from the point of contact (aft end of keel) to the LCF

    Pendulum length

    m|5.2

    Tank length

    m|5.3
  • l,bl, b

    Length and breadth of the flooded compartment

  • LCBLCB

    Longitudinal centre of buoyancy at level keel for the displacement

    m|5.8

    Longitudinal centre of buoyancy from the chosen origin

    m|4.6
  • LCFLCF

    Distance of centre of flotation from midship

    m|4.6
  • LCGLCG

    Longitudinal centre of gravity from midship

    m|5.8
  • LcgiLcg_i

    Longitudinal position of each item (from AP or midship)

  • lhl_h

    Heeling lever

    m|5.4
  • lw1l_{w1}

    Steady wind heeling lever (constant with heel)

    m|5.7
  • LWLL_{WL}

    Waterline length

    m|5.4
  • MM

    Bending moment

    N·mm|2.72.4

    Trimming moment about the LCF

    t·m|5.8
  • mm

    Negative inverse slope (3 or 5 for welded steel in air)

    Number of half-waves along a

    Effective mass

    kg|2.6

    Mass

    t|1.1

    Mass of the ship and everything on board

    t|4.4
  • M(x)M(x)

    Moment from the actual loads

    N·mm|2.6

    Bending moment

    kN·m|2.3
  • m(x)m(x)

    Moment from a unit load at the point and in the direction of the required deflection

    mm|2.6
  • r\mathbf r

    Position vector from O to the point of application

    m|1.7
  • MCT1cmMCT1cm

    Moment to change trim 1 cm

    t·m/cm|5.115.84.8
  • MhM_h

    Heeling moment

    kN·m|5.4
  • mim_i

    Mass of item i

    t|1.7

    Mass of each item (lightship, cargo, tanks, stores, crew)

  • MOM_O

    Moment about O, counter-clockwise positive

    kN·m|1.7
  • MRM_R

    Righting moment

    kN·m|5.1
  • NN

    Number of cycles to failure

    Normal force

    N|2.1

    Axial force

    N|2.2
  • nn

    Rotational speed

    rev/s (rpm/60)|2.7

    Modular ratio

    -|2.4

    Number of bolts

    -|2.2

    Number of readings

    -|1.8

    Number of intervals

    -|1.3

    Number of ordinates

    -|1.3

    Number of equal compartments across the tank breadth

    -|5.3

    Number of intervals (multiple of 3)

    -|4.5

    Number of intervals (even)

    -|4.5
  • N1N_1

    Passengers in cabins with not more than 8 berths

  • N2N_2

    Other passengers

  • NiN_i

    Cycles to failure at range Δσ_i

  • nin_i

    Number of cycles in block i

  • f′′‾\overline{f''}

    Mean second derivative of the curve

    1/m|1.3
  • PP

    Power

    W|2.7

    Point load at the tip

    N|2.6

    Applied load

    kN|2.2

    Upthrust from the blocks at the aft end of keel

    Wind pressure (504 Pa unrestricted service)

    Pa|5.7
  • pp

    Uniform lateral pressure

    MPa (= N/mm²; 1 kPa = 0.001 MPa)|2.9

    Design pressure

    kPa = kN/m²|2.3

    Hydrostatic pressure

    kPa when ρ in t/m³|1.1
  • PEP_E

    Euler critical load

  • qq

    Uniformly distributed load

    N/mm|2.6
  • q(x)q(x)

    Distributed load, positive downward

    kN/m|2.3
  • Q(z)Q(z)

    First moment about the neutral axis of the area beyond z

    mm³|2.4
  • rr

    Radius of gyration about the weaker axis

    mm|2.10

    Shell radius

    mm|2.10

    0.73 + 0.6 OG/d

    -|5.7

    Bilge radius

    m|4.3
  • rir_i

    Distance of bolt i from the centroid

    mm|2.2
  • RkR_k

    Characteristic resistance

    as applicable|2.12
  • ro,dor_o, d_o

    Outer radius / diameter

    mm|2.7
  • SS

    Developed plate area

    m²|1.5

    Wetted surface of the bare hull

    m²|4.9
  • ss

    Stiffener spacing

    Stiffener spacing

    mm|2.5

    Length of the generating curve

    m|1.5

    Factor of roll period T (Table 2.3.4-4)

    -|5.7
  • SiS_i

    Characteristic load effect

    as applicable|2.12
  • SMiSM_i

    Simpson multiplier

    -|4.5
  • SWLSWL

    Safe working load (mass)

  • Sxx,Syy,SxyS_{xx}, S_{yy}, S_{xy}

    Corrected sums of squares and products

    -|1.8
  • TT

    Torque

    N·mm|2.7

    Initial draught

    Roll period

    s|5.7

    Mean draught

    Draught

  • tt

    Plate thickness

    Wall thickness (may vary around the cell)

    mm|2.7

    Thickness

    m|1.5

    Trim by the stern on entering the dock

    cm|5.11

    Trim (positive by the stern when LCG is aft of LCB, with x positive forward)

    cm|5.8

    Trim (positive by the stern with this sign convention)

    m|4.1
  • TAT_A

    Draught at aft perpendicular

    m|4.1
  • TCGTCG

    Transverse offset of G from centreline towards the heeled side

    m|5.4
  • TFT_F

    Draught at forward perpendicular

    m|4.1
  • TMT_M

    Midship draught (mean of port and starboard)

    m|5.8
  • TPCTPC

    TPC in seawater

    t/cm|4.11

    Tonnes per centimetre immersion

    t/cm|4.8
  • TφT_\varphi

    Natural roll period

    s|5.1
  • twt_w

    Web thickness

    mm|2.4
  • uu

    Strain energy per unit volume

    J/m³ = Pa|2.1
  • uiu_i

    Standard uncertainty of input i

    as input|1.8
  • uyu_y

    Standard uncertainty of the result

    as result|1.8
  • VV

    Shear force

    N|2.1

    Volume

    m³|1.5

    Total volume of all enclosed spaces (moulded)

    m³|4.12
  • vv

    Volume of flood water (to the final waterline)

    m³|5.12
  • V(x)V(x)

    Shear force

    kN|2.3
  • V0V_0

    Service speed

    m/s|5.4
  • VcV_c

    Total volume of cargo spaces

    m³|4.12
  • ViV_i

    Volume of part i

    m³|1.5
  • WW

    Elastic section modulus to the extreme fibre considered

    mm³ (rules: cm³)|2.4

    Weight (force)

    kN when m in t|1.1
  • ww

    Deflection (positive downward)

    mm|2.6

    Mass of the lifted load

    Mass shifted

    Added mass (negative when removed)

    t|5.1

    Mass moved

    t|5.2

    Added (or removed, negative) mass

    t|4.8
  • w(x)w(x)

    Weight per unit length

    kN/m|2.3
  • wbw_b

    Ballast mass

    t|5.9
  • wb,ybw_b, y_b

    Anti-heeling ballast mass and its transverse position (opposite side)

    t, m|5.10
  • woffw_{\text{off}}

    Masses on board during the test that are not part of lightship (inclining weights, temporary equipment, people, slack liquids)

    t|5.2
  • wonw_{\text{on}}

    Lightship items missing at the time of the test

    t|5.2
  • xx

    Longitudinal position of the added mass from midship

    m|5.8
  • x0,x1x_0, x_1

    Tabulated arguments bracketing x

    as given|1.6
  • X1X_1

    Factor of B/d (Table 2.3.4-1)

    -|5.7
  • X2X_2

    Factor of C_B (Table 2.3.4-2)

    -|5.7
  • xFx_F

    LCF forward of midship (negative if aft)

    m|5.8
  • xix_i

    Reading i

    as measured|1.8
  • yy

    Transverse offset towards the low side

    m|1.7

    Transverse outreach of the jib head from centreline

    Transverse distance of compartment centroid from centreline

    Transverse distance of the added mass from centreline

    m|5.9

    Half-breadth

    m|4.6
  • y−1,y0,y+1y_{-1}, y_0, y_{+1}

    Three consecutive ordinates with y_0 the largest tabulated

    as given|1.6
  • y(ζ)y(\zeta)

    Half-breadth of the station at height ζ

  • y0,y1y_0, y_1

    Tabulated values

    as given|1.6
  • y0,y1,y2y_0, y_1, y_2

    Three consecutive equally spaced ordinates

    m|4.5
  • yby_b

    Transverse position of ballast (opposite side)

    m|5.9
  • yiy_i

    Ordinate i

    m (or as given)|1.3

    Ordinate at station i

    m|4.5
  • ZZ

    Vertical lever: centroid of A to centre of underwater lateral area (≈ T/2)

    m|5.7
  • zz

    Distance from the neutral axis (positive away from the compression side as per sign convention)

    mm|2.4

    Height of the point above the upright waterline

    m|1.7

    Distance from the x-axis

    m|1.4

    Depth below the still waterline

    m|1.2
  • ziz_i

    Height of the centroid of element i above the reference line

    mm|2.5

    Coordinate of its centre of gravity

    m|1.7
  • zmaxz_{max}

    Distance from the neutral axis to the extreme fibre

    mm|2.4
  • zwz_w

    Vertical distance from the warp block to the centre of lateral underwater resistance (≈ T/2)

  • zWL(x)z_{WL}(x)

    Height of the waterline at station x (linear for trim; sinusoidal/trochoidal for a wave)

  • α\alpha

    Coefficient of linear thermal expansion (steel 12 × 10⁻⁶, aluminium 23 × 10⁻⁶)

    1/K|2.2

    Angle from the positive x-axis, counter-clockwise

    deg|1.7
  • α,β\alpha, \beta

    Coefficients from the table (a/b, edge condition)

    -|2.9

    Coefficients depending on h/b (table)

    -|2.7
  • βw\beta_w

    Correlation factor (S235: 0.80; S355: 0.90)

    -|2.2
  • χ\chi

    Reduction factor from buckling curve a0–d as a function of λ̄

  • Δ\Delta

    Displacement

    Displacement as inclined (from measured draughts and water density)

    t|5.2

    Displacement (seawater)

    Mass displacement

  • δ\delta

    Elongation

    mm|2.1

    Pendulum deflection on the batten

    m|5.2
  • Δ,KG\Delta, KG

    Displacement and KG before the lift

    t, m|5.10
  • Δσ\Delta\sigma

    Stress range

    MPa|2.11
  • Δσ107\Delta\sigma_{10^7}

    Stress range at the knee (10⁷ cycles), e.g. 52.63 MPa for D

    MPa|2.11
  • ΔT\Delta T

    Temperature change

    K|2.2
  • δT\delta T

    Fall of water level since touching

    cm|5.11

    Change of mean draught (bodily sinkage)

    cm|4.8
  • δt\delta t

    Change of trim

    cm|5.8
  • Δlight\Delta_{\text{light}}

    Lightship displacement

    t|4.1
  • Δloaded\Delta_{\text{loaded}}

    Displacement at the load draught

    t|4.1
  • η\eta

    Usage factor (permissible stress coefficient) for the load case

  • γ\gamma

    Safety factor = 1/η

    Shear strain

    rad|2.1
  • γf,i\gamma_{f,i}

    Load factor for load i

  • γm\gamma_m

    Material/resistance factor (DNV-OS-C101: 1.15; EC3 γ_M0 = 1.0)

  • γM1\gamma_{M1}

    Partial factor (1.0 in EN 1993-1-1 recommended)

  • λ\lambda

    Slenderness ratio

  • μ\mu

    Permeability

  • ∇\nabla

    Displacement volume (unchanged)

    m³|5.12

    Displacement volume

    m³|4.94.7

    Moulded displacement volume

    m³|4.3

    Immersed volume

    m³|4.4

    Volume of displacement

    m³|4.1
  • ∇app\nabla_{\text{app}}

    Volume of appendages (rudder, bossings, bilge keels, etc.)

    m³|4.2
  • ∇moulded\nabla_{\text{moulded}}

    Moulded volume from offsets

    m³|4.2
  • ∇total\nabla_{\text{total}}

    Total immersed volume

    m³|4.2
  • ν\nu

    Poisson's ratio (0.3)

    -|2.9

    Poisson's ratio (steel 0.30)

    -|2.1
  • ψ\psi

    Hoisting (dynamic) factor from the lifting standard (typically 1.1–1.3 harbour/offshore in-service; higher for subsea or offboard lifts)

  • ρ\rho

    Fluid density

    t/m³|1.1

    Water density

    t/m³|4.84.4

    Water density (seawater 1.025)

    t/m³|4.1
  • ρ1\rho_1

    Initial water density

    t/m³|4.11
  • ρ2\rho_2

    New water density

    t/m³|4.11
  • ρDW\rho_{DW}

    Dock water density

    t/m³|4.11
  • ρℓ\rho_\ell

    Density of the liquid in the tank

    t/m³|5.3
  • σ\sigma

    Normal stress (tension positive)

    MPa|2.1
  • σ(z)\sigma(z)

    Normal bending stress at distance z from the neutral axis

    MPa|2.4
  • σ0.5t,σ1.5t\sigma_{0.5t}, \sigma_{1.5t}

    Surface stresses read at 0.5t and 1.5t from the weld toe (linear extrapolation)

    MPa|2.11
  • σ1≥σ2\sigma_1 \ge \sigma_2

    Principal stresses

    MPa|2.8
  • σc\sigma_c

    Compressive part of the stress range (absolute value)

    MPa|2.11
  • σE\sigma_E

    Elastic (Euler or plate) critical stress

    MPa|2.10
  • σe\sigma_e

    Equivalent (von Mises) stress

    MPa|2.8
  • σt\sigma_t

    Tensile part of the stress range

    MPa|2.11
  • σallow\sigma_{\text{allow}}

    Allowable bending stress

    MPa|2.9
  • σx,σy\sigma_x, \sigma_y

    Normal stresses on the x and y faces

    MPa|2.8
  • σy\sigma_y

    Specified minimum yield stress (ReH)

    MPa|2.12
  • τ\tau

    Average shear stress

    MPa|2.1
  • τV\tau_V

    Shear stress from the transverse force at the point considered (zero at the extreme bending fibre, 2V/A at the neutral axis for a thin tube)

    MPa|2.8
  • τxy\tau_{xy}

    Shear stress

    MPa|2.8
  • θ\theta

    Rotation of the face, counter-clockwise from x

    rad|2.8

    Slope at the tip

    rad|2.6

    Angle of list

    deg|5.9
  • θp\theta_p

    Angle from x to the σ₁ direction

    rad|2.8

    Angle of the principal axis from the x-axis

    rad|1.4
  • φ\varphi

    Heel angle

    deg|1.7

    Heel angle

    rad|5.5

    Angle of heel produced

    deg|5.2

    Angle of heel

    deg / rad|5.1
  • φ0\varphi_0

    Static heel under steady wind l_w1

    deg|5.7
  • φ1\varphi_1

    Roll angle to windward from static heel

    deg|5.7
  • φ2\varphi_2

    min(second intersection, φf, 50°)

    deg|5.7
  • φf\varphi_f

    Angle of downflooding

    deg|5.6
  • φloll\varphi_{\text{loll}}

    Angle of loll

    deg|5.1