NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.8 Combined stresses, principal stresses and von Mises criterion

Chapter 2 / Section 2.8

Combined stresses, principal stresses and von Mises criterion

Print this section

Plane stress state

At a point of a plate or beam surface the stress state is (σx,σy,τxy)(\sigma_x, \sigma_y, \tau_{xy})(σx​,σy​,τxy​). On a plane rotated by θ\thetaθ (counter-clockwise from the x-axis):

σx′=σx+σy2+σx−σy2cos⁡2θ+τxysin⁡2θ,τx′y′=−σx−σy2sin⁡2θ+τxycos⁡2θ\sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \frac{\sigma_x - \sigma_y}{2}\cos 2\theta + \tau_{xy}\sin 2\theta, \qquad \tau_{x'y'} = -\frac{\sigma_x - \sigma_y}{2}\sin 2\theta + \tau_{xy}\cos 2\thetaσx′​=2σx​+σy​​+2σx​−σy​​cos2θ+τxy​sin2θ,τx′y′​=−2σx​−σy​​sin2θ+τxy​cos2θ

Principal stresses

The planes on which the shear stress vanishes carry the extreme normal stresses:

σ1,2=σx+σy2±(σx−σy2)2+τxy2,tan⁡2θp=2τxyσx−σy\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}, \qquad \tan 2\theta_p = \frac{2\tau_{xy}}{\sigma_x - \sigma_y}σ1,2​=2σx​+σy​​±(2σx​−σy​​)2+τxy2​​,tan2θp​=σx​−σy​2τxy​​

Maximum in-plane shear stress τmax⁡=(σ1−σ2)/2\tau_{\max} = (\sigma_1 - \sigma_2)/2τmax​=(σ1​−σ2​)/2 on planes at 45° to the principal planes; the absolute maximum shear in 3D also considers σ3=0\sigma_3 = 0σ3​=0 (plane stress): τabs=max⁡(∣σ1−σ2∣,∣σ1∣,∣σ2∣)/2\tau_{\text{abs}} = \max(|\sigma_1 - \sigma_2|, |\sigma_1|, |\sigma_2|)/2τabs​=max(∣σ1​−σ2​∣,∣σ1​∣,∣σ2​∣)/2.

Mohr's circle

Plot (σ,τ)(\sigma, \tau)(σ,τ); the circle has centre ((σx+σy)/2, 0)((\sigma_x+\sigma_y)/2,\ 0)((σx​+σy​)/2, 0) and radius R=((σx−σy)/2)2+τxy2R = \sqrt{((\sigma_x-\sigma_y)/2)^2 + \tau_{xy}^2}R=((σx​−σy​)/2)2+τxy2​​. Principal stresses are the intersections with the σ\sigmaσ-axis; a rotation of θ\thetaθ in the material is 2θ2\theta2θ on the circle. Use it to check an FE post-processor's principal stress output.

Yield criteria

  • von Mises (distortion energy) — the criterion used by classification rules and FE post-processing for ductile steel and aluminium:
σe=σx2+σy2−σxσy+3τxy2=σ12−σ1σ2+σ22≤σallow\sigma_e = \sqrt{\sigma_x^2 + \sigma_y^2 - \sigma_x\sigma_y + 3\tau_{xy}^2} = \sqrt{\sigma_1^2 - \sigma_1\sigma_2 + \sigma_2^2} \le \sigma_{\text{allow}}σe​=σx2​+σy2​−σx​σy​+3τxy2​​=σ12​−σ1​σ2​+σ22​​≤σallow​

Pure shear yields at τy=σy/3=0.577 σy\tau_y = \sigma_y/\sqrt3 = 0.577\,\sigma_yτy​=σy​/3​=0.577σy​.

  • Tresca (maximum shear) — σ1−σ2≤σy\sigma_1 - \sigma_2 \le \sigma_yσ1​−σ2​≤σy​ (for σ1>0>σ2\sigma_1 > 0 > \sigma_2σ1​>0>σ2​); slightly conservative (up to 15 %) relative to von Mises; pure shear yields at 0.5 σy0.5\,\sigma_y0.5σy​.
  • Maximum principal stress — used for brittle materials and for fatigue of welds (the principal stress range normal to the weld, DNV-RP-C203).

Combined loading in practice

  • Hull girder + local: deck plating carries the hull girder stress σx\sigma_xσx​ plus local bending stress from deck load plus shear; rules combine them with specified factors (Section 7.4) because the maxima rarely coincide.
  • Pedestal / column: axial σ=N/A\sigma = N/Aσ=N/A, bending σ=M/W\sigma = M/Wσ=M/W (add algebraically at the same fibre), shear τ=V/Aw\tau = V/A_wτ=V/Aw​ or 2V/A2V/A2V/A, torsion τ=T/(2Amt)\tau = T/(2A_m t)τ=T/(2Am​t) (add algebraically to the shear at the same point), then von Mises.
  • Shafts: bending + torsion → von Mises σe=σ2+3τ2\sigma_e = \sqrt{\sigma^2 + 3\tau^2}σe​=σ2+3τ2​ or the equivalent-moment method (Section 2.7).
  • FE results: report von Mises for yield checks of shell elements (membrane and surface values as the rule requires), principal stresses for fatigue and for brittle components; never compare an element-average von Mises from a coarse mesh with a fine-mesh allowable (DNV-CG-0127, Section 7.11).

Stress concentrations

At holes, notches, cut-outs and bracket toes the local stress is KtK_tKt​ times the nominal (KtK_tKt​ = 3 for a small circular hole in a plate under uniaxial tension; 2 for equibiaxial). Elastic design with rule allowables accepts local yielding at KtK_tKt​ locations under static load; for fatigue, KtK_tKt​ (or the hot-spot stress) is the governing quantity (Section 2.11).

Formulas

01Stress transformation (plane stress)
σx′=σx+σy2+σx−σy2cos⁡2θ+τxysin⁡2θ,τx′y′=−σx−σy2sin⁡2θ+τxycos⁡2θ\sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \frac{\sigma_x - \sigma_y}{2}\cos 2\theta + \tau_{xy}\sin 2\theta, \qquad \tau_{x'y'} = -\frac{\sigma_x - \sigma_y}{2}\sin 2\theta + \tau_{xy}\cos 2\thetaσx′​=2σx​+σy​​+2σx​−σy​​cos2θ+τxy​sin2θ,τx′y′​=−2σx​−σy​​sin2θ+τxy​cos2θ
SymbolDescriptionUnit
σx,σy\sigma_x, \sigma_yσx​,σy​Normal stresses on the x and y facesMPa
τxy\tau_{xy}τxy​Shear stressMPa
θ\thetaθRotation of the face, counter-clockwise from xrad

Result unit MPa

02Principal stresses and principal direction
σ1,2=σx+σy2±(σx−σy2)2+τxy2,tan⁡2θp=2 τxyσx−σy\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}, \qquad \tan 2\theta_p = \frac{2\,\tau_{xy}}{\sigma_x - \sigma_y}σ1,2​=2σx​+σy​​±(2σx​−σy​​)2+τxy2​​,tan2θp​=σx​−σy​2τxy​​
SymbolDescriptionUnit
σ1≥σ2\sigma_1 \ge \sigma_2σ1​≥σ2​Principal stressesMPa
θp\theta_pθp​Angle from x to the σ₁ directionrad

Result unit MPa

03Maximum shear stress
τmax⁡=σ1−σ22=(σx−σy2)2+τxy2\tau_{\max} = \frac{\sigma_1 - \sigma_2}{2} = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}τmax​=2σ1​−σ2​​=(2σx​−σy​​)2+τxy2​​

Result unit MPa

In-plane value; for plane stress the absolute maximum also considers σ₃ = 0.

04von Mises equivalent stress (plane stress)
σe=σx2+σy2−σx σy+3 τxy2=σ12−σ1σ2+σ22\sigma_e = \sqrt{\sigma_x^2 + \sigma_y^2 - \sigma_x\,\sigma_y + 3\,\tau_{xy}^2} = \sqrt{\sigma_1^2 - \sigma_1\sigma_2 + \sigma_2^2}σe​=σx2​+σy2​−σx​σy​+3τxy2​​=σ12​−σ1​σ2​+σ22​​
SymbolDescriptionUnit
σe\sigma_eσe​Equivalent (von Mises) stressMPa

Result unit MPa

Uniaxial + shear: σ_e = √(σ² + 3τ²). Yield when σ_e = σ_y.

05von Mises equivalent stress (general 3D)
σe=12[(σ1−σ2)2+(σ2−σ3)2+(σ3−σ1)2]\sigma_e = \sqrt{\tfrac{1}{2}\left[(\sigma_1 - \sigma_2)^2 + (\sigma_2 - \sigma_3)^2 + (\sigma_3 - \sigma_1)^2\right]}σe​=21​[(σ1​−σ2​)2+(σ2​−σ3​)2+(σ3​−σ1​)2]​

Result unit MPa

06Tresca criterion
max⁡(∣σ1−σ2∣, ∣σ2−σ3∣, ∣σ3−σ1∣)≤σy\max\left(|\sigma_1 - \sigma_2|,\ |\sigma_2 - \sigma_3|,\ |\sigma_3 - \sigma_1|\right) \le \sigma_ymax(∣σ1​−σ2​∣, ∣σ2​−σ3​∣, ∣σ3​−σ1​∣)≤σy​

Result unit MPa

07Shear yield stress
τy=σy3=0.577 σy (von Mises),τy=0.5 σy (Tresca)\tau_y = \frac{\sigma_y}{\sqrt 3} = 0.577\,\sigma_y \ (\text{von Mises}), \qquad \tau_y = 0.5\,\sigma_y \ (\text{Tresca})τy​=3​σy​​=0.577σy​ (von Mises),τy​=0.5σy​ (Tresca)

Result unit MPa

08Combined axial, bending, shear and torsion at a point of a tube
σ=NA±MW,τ=T2Amt+τV,σe=σ2+3τ2\sigma = \frac{N}{A} \pm \frac{M}{W}, \qquad \tau = \frac{T}{2 A_m t} + \tau_V, \qquad \sigma_e = \sqrt{\sigma^2 + 3\tau^2}σ=AN​±WM​,τ=2Am​tT​+τV​,σe​=σ2+3τ2​
SymbolDescriptionUnit
τV\tau_VτV​Shear stress from the transverse force at the point considered (zero at the extreme bending fibre, 2V/A at the neutral axis for a thin tube)MPa

Result unit MPa

Tables

Elastic stress concentration factors KtK_tKt​ for common ship structural details (nominal stress basis, indicative)

DetailKtK_tKt​ (approx.)Note
Small circular hole in a wide plate, uniaxial tension3.0Kirsch solution; 2.0 for equibiaxial tension; 4.0 for pure shear
Elliptical hole, major axis 2a transverse to load, minor 2b1+2a/b1 + 2a/b1+2a/bCrack-like for a/b large
Circular cut-out with b/W = 0.3 (finite plate)≈ 2.4Peterson's charts
Scallop / cut-out in a web for a stiffener (well-rounded)1.5–2.5Depends on radius and web stress
Bracket toe, well-faired (soft toe)1.3–1.8Hot-spot approach for fatigue
Bracket toe, abrupt (no taper)2.5–4Avoid in fatigue-loaded areas
Hatch corner, elliptical/parabolic1.5–2.5Insert plates and radius per class guidance
Fillet-welded attachment on a plate (toe)2–3 (notch)Covered by the S–N detail category, not Kt, in RP-C203
Source: Pilkey & Pilkey, Peterson's Stress Concentration Factors, 3rd ed. (2008); Hughes & Paik (2010) Ch. 15; DNV-RP-C203 App. A (detail categories). Indicative values; use the chart or FE hot-spot method for approval work.

Examples

#01

Principal stresses, Mohr's circle and von Mises for a deck plate element

Worked example

Problem

An element of the strength deck has σx=120\sigma_x = 120σx​=120 MPa (hull girder, longitudinal), σy=40\sigma_y = 40σy​=40 MPa (transverse, from deck load) and τxy=50\tau_{xy} = 50τxy​=50 MPa (hull girder shear near a hatch corner). Find the principal stresses and their direction, the maximum shear stress, and the von Mises stress; compare with σ_y = 235 MPa and with an allowable of 0.8 σ_y.

Solution

Centre of Mohr's circle: (120+40)/2=80(120 + 40)/2 = 80(120+40)/2=80 MPa. Radius: R=402+502=64.0R = \sqrt{40^2 + 50^2} = 64.0R=402+502​=64.0 MPa.

σ1=80+64.0=144.0 MPa,σ2=80−64.0=16.0 MPa\sigma_1 = 80 + 64.0 = 144.0\ \text{MPa}, \qquad \sigma_2 = 80 - 64.0 = 16.0\ \text{MPa}σ1​=80+64.0=144.0 MPa,σ2​=80−64.0=16.0 MPa tan⁡2θp=2×50120−40=1.25⇒2θp=51.3°, θp=25.7°\tan 2\theta_p = \frac{2 \times 50}{120 - 40} = 1.25 \Rightarrow 2\theta_p = 51.3°, \ \theta_p = 25.7°tan2θp​=120−402×50​=1.25⇒2θp​=51.3°, θp​=25.7°

(σ₁ acts at 25.7° counter-clockwise from the longitudinal axis.)

τmax⁡=R=64.0\tau_{\max} = R = 64.0τmax​=R=64.0 MPa (in-plane); absolute maximum with σ₃ = 0: max⁡(64.0,72.0,8.0)=72.0\max(64.0, 72.0, 8.0) = 72.0max(64.0,72.0,8.0)=72.0 MPa.

von Mises:

σe=1202+402−120×40+3×502=14 400+1600−4800+7500=18 700=136.7 MPa\sigma_e = \sqrt{120^2 + 40^2 - 120 \times 40 + 3 \times 50^2} = \sqrt{14\,400 + 1600 - 4800 + 7500} = \sqrt{18\,700} = 136.7\ \text{MPa}σe​=1202+402−120×40+3×502​=14400+1600−4800+7500​=18700​=136.7 MPa

Check via principal stresses: 1442−144×16+162=20 736−2304+256=136.7\sqrt{144^2 - 144 \times 16 + 16^2} = \sqrt{20\,736 - 2304 + 256} = 136.71442−144×16+162​=20736−2304+256​=136.7 ✓.

Tresca: σ1−σ2=128\sigma_1 - \sigma_2 = 128σ1​−σ2​=128 MPa (or 2τabs=1442\tau_{\text{abs}} = 1442τabs​=144 MPa with σ₃) — more conservative.

Against σ_y: UC=136.7/235=0.58UC = 136.7/235 = 0.58UC=136.7/235=0.58; against 0.8 σy=1880.8\,\sigma_y = 1880.8σy​=188 MPa: UC=0.73UC = 0.73UC=0.73. Acceptable at this (general) level; the rule check (Section 7.4) combines hull girder and local stresses with its own factors and allowables.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 7 (Analysis of stress and strain: plane stress, principal stresses, Mohr's circle), Ch. 8 (Applications of plane stress — combined loadings)Textbook
Hibbeler, Mechanics of Materials, 10th ed. (2017)Clause Ch. 9 (Stress transformation), Ch. 10.7 (Theories of failure)Textbook
DNV-CG-0127 Finite element analysisClause Sec. on yield check acceptance criteria (von Mises stress of shell elements)Recommended

Class guideline referenced by DNV Rules Pt.3 Ch.7; confirm edition.

Pilkey & Pilkey, Peterson's Stress Concentration Factors, 3rd ed. (2008)Clause Ch. 4 (Holes), Ch. 5 (Miscellaneous design elements)Textbook
Previous · 2.7Shear stress and torsionNext · 2.9Plate bending under lateral pressure

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Plane stress state
  • Principal stresses
  • Mohr's circle
  • Yield criteria
  • Combined loading in practice
  • Stress concentrations
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 7 (Analysis of stress and strain: plane stress, principal stresses, Mohr's circle), Ch. 8 (Applications of plane stress — combined loadings)

  • Hibbeler, Mechanics of Materials, 10th ed. (2017)

    Ch. 9 (Stress transformation), Ch. 10.7 (Theories of failure)

  • DNV-CG-0127 Finite element analysis

    Sec. on yield check acceptance criteria (von Mises stress of shell elements)

  • Pilkey & Pilkey, Peterson's Stress Concentration Factors, 3rd ed. (2008)

    Ch. 4 (Holes), Ch. 5 (Miscellaneous design elements)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.