NavArch Handbook
Chapter 2 / Section 2.8
At a point of a plate or beam surface the stress state is . On a plane rotated by (counter-clockwise from the x-axis):
The planes on which the shear stress vanishes carry the extreme normal stresses:
Maximum in-plane shear stress on planes at 45° to the principal planes; the absolute maximum shear in 3D also considers (plane stress): .
Plot ; the circle has centre and radius . Principal stresses are the intersections with the -axis; a rotation of in the material is on the circle. Use it to check an FE post-processor's principal stress output.
Pure shear yields at .
At holes, notches, cut-outs and bracket toes the local stress is times the nominal ( = 3 for a small circular hole in a plate under uniaxial tension; 2 for equibiaxial). Elastic design with rule allowables accepts local yielding at locations under static load; for fatigue, (or the hot-spot stress) is the governing quantity (Section 2.11).
| Symbol | Description | Unit |
|---|---|---|
| Normal stresses on the x and y faces | MPa | |
| Shear stress | MPa | |
| Rotation of the face, counter-clockwise from x | rad |
Result unit MPa
| Symbol | Description | Unit |
|---|---|---|
| Principal stresses | MPa | |
| Angle from x to the σ₁ direction | rad |
Result unit MPa
Result unit MPa
In-plane value; for plane stress the absolute maximum also considers σ₃ = 0.
| Symbol | Description | Unit |
|---|---|---|
| Equivalent (von Mises) stress | MPa |
Result unit MPa
Uniaxial + shear: σ_e = √(σ² + 3τ²). Yield when σ_e = σ_y.
Result unit MPa
Result unit MPa
Result unit MPa
| Symbol | Description | Unit |
|---|---|---|
| Shear stress from the transverse force at the point considered (zero at the extreme bending fibre, 2V/A at the neutral axis for a thin tube) | MPa |
Result unit MPa
| Detail | (approx.) | Note |
|---|---|---|
| Small circular hole in a wide plate, uniaxial tension | 3.0 | Kirsch solution; 2.0 for equibiaxial tension; 4.0 for pure shear |
| Elliptical hole, major axis 2a transverse to load, minor 2b | Crack-like for a/b large | |
| Circular cut-out with b/W = 0.3 (finite plate) | ≈ 2.4 | Peterson's charts |
| Scallop / cut-out in a web for a stiffener (well-rounded) | 1.5–2.5 | Depends on radius and web stress |
| Bracket toe, well-faired (soft toe) | 1.3–1.8 | Hot-spot approach for fatigue |
| Bracket toe, abrupt (no taper) | 2.5–4 | Avoid in fatigue-loaded areas |
| Hatch corner, elliptical/parabolic | 1.5–2.5 | Insert plates and radius per class guidance |
| Fillet-welded attachment on a plate (toe) | 2–3 (notch) | Covered by the S–N detail category, not Kt, in RP-C203 |
Worked example
Problem
An element of the strength deck has MPa (hull girder, longitudinal), MPa (transverse, from deck load) and MPa (hull girder shear near a hatch corner). Find the principal stresses and their direction, the maximum shear stress, and the von Mises stress; compare with σ_y = 235 MPa and with an allowable of 0.8 σ_y.
Solution
Centre of Mohr's circle: MPa. Radius: MPa.
(σ₁ acts at 25.7° counter-clockwise from the longitudinal axis.)
MPa (in-plane); absolute maximum with σ₃ = 0: MPa.
von Mises:
Check via principal stresses: ✓.
Tresca: MPa (or MPa with σ₃) — more conservative.
Against σ_y: ; against MPa: . Acceptable at this (general) level; the rule check (Section 7.4) combines hull girder and local stresses with its own factors and allowables.
Class guideline referenced by DNV Rules Pt.3 Ch.7; confirm edition.