NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.9 Plate bending under lateral pressure

Chapter 2 / Section 2.9

Plate bending under lateral pressure

Print this section

Why plates differ from beams

A plate panel between stiffeners is supported on all four edges and bends in two directions; the Poisson coupling increases its stiffness by 1/(1−ν2)=1.101/(1-\nu^2) = 1.101/(1−ν2)=1.10 for steel. Flexural rigidity per unit width:

D=E t312 (1−ν2)D = \frac{E\,t^3}{12\,(1-\nu^2)}D=12(1−ν2)Et3​

Long plates (a/b ≥ 2): the plate strip

When the panel is long relative to its width bbb (stiffener spacing), the central region behaves as a strip of unit width spanning bbb between the stiffeners. With the stiffeners acting as clamped supports (continuous plating over several stiffeners under uniform pressure ppp):

Medge=p b212,σmax⁡=6Mt2=p b22 t2,δmax⁡=p b4384 D=0.0284 p b4E t3M_{\text{edge}} = \frac{p\,b^2}{12}, \qquad \sigma_{\max} = \frac{6M}{t^2} = \frac{p\,b^2}{2\,t^2}, \qquad \delta_{\max} = \frac{p\,b^4}{384\,D} = 0.0284\,\frac{p\,b^4}{E\,t^3}Medge​=12pb2​,σmax​=t26M​=2t2pb2​,δmax​=384Dpb4​=0.0284Et3pb4​

This is the basis of the classical rule plate-thickness formula t=C bp/σallowt = C\,b\sqrt{p/\sigma_{\text{allow}}}t=Cbp/σallow​​ (with CCC including the end fixity, in rule units) — Section 7.5. For simply supported edges: M=pb2/8M = p b^2/8M=pb2/8, σ=0.75 pb2/t2\sigma = 0.75\,p b^2/t^2σ=0.75pb2/t2, δ=0.1422 pb4/(Et3)\delta = 0.1422\,p b^4/(E t^3)δ=0.1422pb4/(Et3).

Finite panels: Timoshenko / Roark coefficients

For a rectangular panel a×ba \times ba×b (a≥ba \ge ba≥b) under uniform pressure:

σmax⁡=β p b2t2,δmax⁡=α p b4E t3\sigma_{\max} = \beta\,\frac{p\,b^2}{t^2}, \qquad \delta_{\max} = \alpha\,\frac{p\,b^4}{E\,t^3}σmax​=βt2pb2​,δmax​=αEt3pb4​

with α,β\alpha, \betaα,β from the table (functions of a/ba/ba/b and edge conditions). For a/b≥2a/b \ge 2a/b≥2 the values are within 1 % of the strip values. Real ship panels lie between simply supported and clamped; the rules assume clamped (continuous plating) for pressure loads.

Small- vs large-deflection theory

The formulas above are linear (small deflection, δ<t/2\delta < t/2δ<t/2). Thin plates under high pressure develop membrane stresses that carry part of the load ("large-deflection" or Föppl–von Kármán theory): the deflection grows less than linearly with ppp and the bending stress is reduced, but membrane tension at the edges is added. Class rules for plating are calibrated against this behaviour and allow nominal bending stresses close to yield (permanent set criteria for bottom slamming, deck loads from wheeled vehicles — DNV Pt.3 Ch.6).

Point and patch loads

Wheel loads (forklifts, vehicles) and container corner castings load small patches; use the Roark/Timoshenko solutions for a concentrated or patch load on a clamped plate, or the rule formulas for wheel loading (DNV Pt.3 Ch.6 and Pt.5 for ro-ro), which include the tyre print dimensions.

Stiffener reaction and effective plate

The plate transmits p b/2p\,b/2pb/2 per unit length to each adjacent stiffener (hence the stiffener line load q=p sq = p\,sq=ps, Section 2.3); and the plate acts as the stiffener's flange (Section 2.5). Plate, stiffener and girder form one load path; the three checks must use consistent assumptions.

Formulas

01Plate flexural rigidity
D=E t312 (1−ν2)D = \frac{E\,t^3}{12\,(1-\nu^2)}D=12(1−ν2)Et3​
SymbolDescriptionUnit
DDDFlexural rigidity per unit widthN·mm
tttPlate thicknessmm
ν\nuνPoisson's ratio (0.3)-

Result unit N·mm

02Long plate strip, clamped edges — stress and deflection
σmax⁡=p b22 t2,δmax⁡=0.0284 p b4E t3\sigma_{\max} = \frac{p\,b^2}{2\,t^2}, \qquad \delta_{\max} = 0.0284\,\frac{p\,b^4}{E\,t^3}σmax​=2t2pb2​,δmax​=0.0284Et3pb4​
SymbolDescriptionUnit
pppUniform lateral pressureMPa (= N/mm²; 1 kPa = 0.001 MPa)
bbbShort span (stiffener spacing)mm

Result unit MPa, mm

σ_max at the clamped edge (support); midspan stress is half. 0.0284 = 12(1−ν²)/384 for ν = 0.3.

03Long plate strip, simply supported edges
σmax⁡=0.75 p b2t2,δmax⁡=0.1422 p b4E t3\sigma_{\max} = 0.75\,\frac{p\,b^2}{t^2}, \qquad \delta_{\max} = 0.1422\,\frac{p\,b^4}{E\,t^3}σmax​=0.75t2pb2​,δmax​=0.1422Et3pb4​

Result unit MPa, mm

04Rectangular panel, uniform pressure (Roark form)
σmax⁡=β p b2t2,δmax⁡=α p b4E t3\sigma_{\max} = \beta\,\frac{p\,b^2}{t^2}, \qquad \delta_{\max} = \alpha\,\frac{p\,b^4}{E\,t^3}σmax​=βt2pb2​,δmax​=αEt3pb4​
SymbolDescriptionUnit
α,β\alpha, \betaα,βCoefficients from the table (a/b, edge condition)-
aaaLong sidemm

Result unit MPa, mm

05Required thickness from a bending stress limit (strip, clamped)
treq=b p2 σallowt_{\text{req}} = b\,\sqrt{\frac{p}{2\,\sigma_{\text{allow}}}}treq​=b2σallow​p​​
SymbolDescriptionUnit
σallow\sigma_{\text{allow}}σallow​Allowable bending stressMPa

Result unit mm

Add the corrosion addition t_c. Rule formulas have the same structure with rule-specific coefficients and units (Section 7.5).

06Stiffener line load from plate pressure
q=p sq = p\,sq=ps
SymbolDescriptionUnit
sssStiffener spacingm

Result unit kN/m

Tables

Coefficients β (stress) and α (deflection) for rectangular plates under uniform pressure, ν = 0.3

a/ba/ba/bAll edges clamped: β\betaβAll edges clamped: α\alphaαAll edges simply supported: β\betaβAll edges simply supported: α\alphaα
1.00.30780.01380.28740.0444
1.20.38340.01880.37620.0616
1.40.43560.02260.45300.0770
1.60.46800.02510.51720.0906
1.80.48720.02670.56880.1017
2.00.49740.02770.61020.1110
3.00.50000.02840.71340.1335
4.00.50000.02840.74100.1400
5.00.50000.02840.74760.1417
∞0.50000.02840.75000.1421
Source: Young, Budynas & Sadegh, Roark's Formulas for Stress and Strain, 8th ed. (2012), Table 11.4, cases 1a (simply supported) and 8a (clamped); Timoshenko & Woinowsky-Krieger (1959) Ch. 5–6.

Clamped: σ_max at the middle of the long edge. Simply supported: σ_max at the centre.

Examples

#01

Deck plate between stiffeners under deck cargo pressure

Worked example

Problem

Deck plating t=10t = 10t=10 mm, stiffener spacing b=600b = 600b=600 mm, frame spacing a=2400a = 2400a=2400 mm (a/b=4a/b = 4a/b=4), uniform deck load p=25p = 25p=25 kPa. Find the maximum bending stress and deflection for clamped edges, and the thickness that would be required for an allowable bending stress of 160 MPa.

Solution

p=25p = 25p=25 kPa =0.025= 0.025=0.025 N/mm². a/b=4⇒β=0.500a/b = 4 \Rightarrow \beta = 0.500a/b=4⇒β=0.500, α=0.0284\alpha = 0.0284α=0.0284 (clamped).

σmax⁡=0.500×0.025×6002102=0.500×90=45.0 MPa\sigma_{\max} = 0.500 \times \frac{0.025 \times 600^2}{10^2} = 0.500 \times 90 = 45.0\ \text{MPa}σmax​=0.500×1020.025×6002​=0.500×90=45.0 MPa δmax⁡=0.0284×0.025×6004206 000×103=0.0284×3.24×1092.06×108=0.45 mm\delta_{\max} = 0.0284 \times \frac{0.025 \times 600^4}{206\,000 \times 10^3} = 0.0284 \times \frac{3.24 \times 10^9}{2.06 \times 10^8} = 0.45\ \text{mm}δmax​=0.0284×206000×1030.025×6004​=0.0284×2.06×1083.24×109​=0.45 mm

Required thickness for 160 MPa: t=6000.025/(2×160)=600×0.00884=5.3t = 600\sqrt{0.025/(2 \times 160)} = 600 \times 0.00884 = 5.3t=6000.025/(2×160)​=600×0.00884=5.3 mm (+ corrosion addition). The 10 mm plate is governed by other requirements (minimum thickness, hull girder buckling, wheel loads), not by the 25 kPa uniform pressure — a typical finding for PSV decks, which are designed for 5–10 t/m² (50–100 kPa) cargo loads: at 100 kPa the stress would be 180 MPa and treq=10.6t_{\text{req}} = 10.6treq​=10.6 mm.

References

Timoshenko & Woinowsky-Krieger, Theory of Plates and Shells, 2nd ed. (1959)Clause Ch. 5 (Simply supported rectangular plates), Ch. 6 (Rectangular plates with various edge conditions), Ch. 13 (Large deflections)Textbook
Roark's Formulas for Stress and Strain, 8th ed. (2012)Clause Table 11.4 (Flat rectangular plates)Textbook
Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)Clause Ch. 9 (Plate bending — small and large deflection, permanent set)Textbook
DNV Rules for Classification — Ships, Pt.3 Ch.6 (Hull local scantling)Clause Sec. 4 (Plating — thickness requirements for lateral pressure)Mandatory

Confirm edition in force.

Previous · 2.8Combined stresses, principal stresses and von Mises criterionNext · 2.10Column and plate buckling

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Why plates differ from beams
  • Long plates (a/b ≥ 2): the plate strip
  • Finite panels: Timoshenko / Roark coefficients
  • Small- vs large-deflection theory
  • Point and patch loads
  • Stiffener reaction and effective plate
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Timoshenko & Woinowsky-Krieger, Theory of Plates and Shells, 2nd ed. (1959)

    Ch. 5 (Simply supported rectangular plates), Ch. 6 (Rectangular plates with various edge conditions), Ch. 13 (Large deflections)

  • Roark's Formulas for Stress and Strain, 8th ed. (2012)

    Table 11.4 (Flat rectangular plates)

  • Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)

    Ch. 9 (Plate bending — small and large deflection, permanent set)

  • DNV Rules for Classification — Ships, Pt.3 Ch.6 (Hull local scantling)

    Sec. 4 (Plating — thickness requirements for lateral pressure)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.