NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.10 Column and plate buckling

Chapter 2 / Section 2.10

Column and plate buckling

Print this section

Buckling as a stability problem

A compression member or plate becomes unstable at a critical load that depends on stiffness (EEE, III) and geometry (slenderness), not on yield strength — until the critical stress approaches yield, where the two interact. High-strength steel does not raise the elastic buckling stress.

Euler column

PE=π2EI(KL)2,σE=π2Eλ2,λ=KLr,r=I/AP_E = \frac{\pi^2 E I}{(K L)^2}, \qquad \sigma_E = \frac{\pi^2 E}{\lambda^2}, \qquad \lambda = \frac{K L}{r}, \quad r = \sqrt{I/A}PE​=(KL)2π2EI​,σE​=λ2π2E​,λ=rKL​,r=I/A​

KKK = effective length factor (table). Valid while σE≤σy/2\sigma_E \le \sigma_y/2σE​≤σy​/2 (slender columns, λ>λlim=π2E/σy\lambda > \lambda_{\text{lim}} = \pi\sqrt{2E/\sigma_y}λ>λlim​=π2E/σy​​ = 132 for mild steel).

Inelastic range — Johnson–Ostenfeld correction

For σE>σy/2\sigma_E > \sigma_y/2σE​>σy​/2 (stocky columns and most ship plating):

σcr=σy(1−σy4 σE)\sigma_{cr} = \sigma_y\left(1 - \frac{\sigma_y}{4\,\sigma_E}\right)σcr​=σy​(1−4σE​σy​​)

This parabola is used by DNV and many ship rules to connect the elastic buckling stress to yield. Eurocode 3 uses instead the Perry–Robertson-type buckling curves (χ\chiχ factors, curves a0–d) which include initial imperfections explicitly; for hot-finished tubes curve a applies.

Pillars in ships

Rules give the pillar's required area as a function of load, length and radius of gyration (DNV Pt.3 Ch.6 — pillars), essentially the Euler/Johnson approach with a usage factor. Load: the deck reaction at the pillar head (tributary deck area × pressure, plus loads from decks above transmitted by pillars in line). Effective length: between deck connections, K=1.0K = 1.0K=1.0 (pinned) unless the end brackets justify less.

Plate buckling (elastic)

For a rectangular plate a×ba \times ba×b simply supported on four edges under uniaxial compression along aaa:

σcr=k π2E12 (1−ν2)(tb)2=0.904 k E(tb)2\sigma_{cr} = k\,\frac{\pi^2 E}{12\,(1-\nu^2)}\left(\frac{t}{b}\right)^2 = 0.904\,k\,E\left(\frac{t}{b}\right)^2σcr​=k12(1−ν2)π2E​(bt​)2=0.904kE(bt​)2

k=4k = 4k=4 for a/b≥1a/b \ge 1a/b≥1 (minimum over the number of half-waves); k=(b/a+a/b)2k = (b/a + a/b)^2k=(b/a+a/b)2 for a single half-wave; for a long plate compressed in the short direction (bbb transverse to the load) k≈1k \approx 1k≈1 (wide plate — relevant to transversely framed decks). Shear: ks=5.34+4(b/a)2k_s = 5.34 + 4(b/a)^2ks​=5.34+4(b/a)2 (a≥ba \ge ba≥b), τcr=ks⋅0.904 E (t/b)2\tau_{cr} = k_s \cdot 0.904\,E\,(t/b)^2τcr​=ks​⋅0.904E(t/b)2. Combined loads: interaction formulas (DNV-RP-C201).

Plate slenderness: β=btσyE\beta = \dfrac{b}{t}\sqrt{\dfrac{\sigma_y}{E}}β=tb​Eσy​​​; plates with β<1.0\beta < 1.0β<1.0 are "stocky" (yield before buckling), β≈2\beta \approx 2β≈2 typical of deck plating.

Post-buckling and effective width

A plate does not collapse at σcr\sigma_{cr}σcr​: the edges near the stiffeners continue to carry load. The effective width beffb_{\text{eff}}beff​ (von Kármán: beff/b=σcr/σyb_{\text{eff}}/b = \sqrt{\sigma_{cr}/\sigma_y}beff​/b=σcr​/σy​​; Faulkner: beff/b=2/β−1/β2b_{\text{eff}}/b = 2/\beta - 1/\beta^2beff​/b=2/β−1/β2) is used for the ultimate strength of stiffened panels and the hull girder (Section 7.3 and 7.8).

Stiffened panels and tripping

Failure modes: plate buckling between stiffeners; stiffener column (flexural) buckling with the plate as flange; tripping (lateral-torsional buckling of the stiffener) — prevented by tripping brackets and by limits on flange proportions; overall grillage buckling. DNV-RP-C201 and the PULS code (DNV) treat these; Section 7.8.

Shells

Cylindrical shells (pedestals, masts, pipes) in axial compression and bending buckle at σcr=0.605 E t/r\sigma_{cr} = 0.605\,E\,t/rσcr​=0.605Et/r (classical, perfect shell) but real shells reach only 20–60 % of this because of imperfection sensitivity; use DNV-RP-C202 or EN 1993-1-6.

Formulas

01Euler buckling load and stress
PE=π2EI(KL)2,σE=π2Eλ2,λ=KLr,r=IAP_E = \frac{\pi^2 E I}{(K L)^2}, \qquad \sigma_E = \frac{\pi^2 E}{\lambda^2}, \qquad \lambda = \frac{K L}{r}, \qquad r = \sqrt{\frac{I}{A}}PE​=(KL)2π2EI​,σE​=λ2π2E​,λ=rKL​,r=AI​​
SymbolDescriptionUnit
PEP_EPE​Euler critical loadN
KKKEffective length factor-
LLLUnsupported lengthmm
λ\lambdaλSlenderness ratio-
rrrRadius of gyration about the weaker axismm

Result unit N, MPa

02Limit slenderness for elastic buckling
λlim=π2Eσy(=132 for σy=235, 108 for 355)\lambda_{\text{lim}} = \pi\sqrt{\frac{2E}{\sigma_y}} \quad (= 132 \text{ for } \sigma_y = 235,\ 108 \text{ for } 355)λlim​=πσy​2E​​(=132 for σy​=235, 108 for 355)

Result unit -

03Johnson–Ostenfeld critical stress
σcr={σEσE≤σy/2σy(1−σy4 σE)σE>σy/2\sigma_{cr} = \begin{cases} \sigma_E & \sigma_E \le \sigma_y/2 \\ \sigma_y\left(1 - \dfrac{\sigma_y}{4\,\sigma_E}\right) & \sigma_E > \sigma_y/2 \end{cases}σcr​=⎩⎨⎧​σE​σy​(1−4σE​σy​​)​σE​≤σy​/2σE​>σy​/2​
SymbolDescriptionUnit
σE\sigma_EσE​Elastic (Euler or plate) critical stressMPa

Result unit MPa

Applies to columns and to plates (with σ_E = plate elastic buckling stress).

04Elastic plate buckling stress (uniaxial compression)
σcr=k π2E12(1−ν2)(tb)2=0.904 k E(tb)2,k=(m ba+am b)2≥4\sigma_{cr} = k\,\frac{\pi^2 E}{12(1-\nu^2)}\left(\frac{t}{b}\right)^2 = 0.904\,k\,E\left(\frac{t}{b}\right)^2, \qquad k = \left(\frac{m\,b}{a} + \frac{a}{m\,b}\right)^2 \ge 4σcr​=k12(1−ν2)π2E​(bt​)2=0.904kE(bt​)2,k=(amb​+mba​)2≥4
SymbolDescriptionUnit
kkkBuckling coefficient (4.0 for long simply supported plate loaded along a)-
bbbPlate width perpendicular to the compression (stiffener spacing)mm
mmmNumber of half-waves along a-

Result unit MPa

05Elastic plate buckling in shear
τcr=ks 0.904 E(tb)2,ks=5.34+4(ba)2(a≥b)\tau_{cr} = k_s\,0.904\,E\left(\frac{t}{b}\right)^2, \qquad k_s = 5.34 + 4\left(\frac{b}{a}\right)^2 \quad (a \ge b)τcr​=ks​0.904E(bt​)2,ks​=5.34+4(ab​)2(a≥b)

Result unit MPa

06Plate slenderness ratio
β=btσyE\beta = \frac{b}{t}\sqrt{\frac{\sigma_y}{E}}β=tb​Eσy​​​

Result unit -

β ≈ 2.0 for 600/10 mild steel; σ_cr(elastic)/σ_y = 3.6/β² for k = 4.

07Effective width of a buckled plate (Faulkner)
beffb=2β−1β2(β≥1),beffb=1 (β<1)\frac{b_{\text{eff}}}{b} = \frac{2}{\beta} - \frac{1}{\beta^2} \quad (\beta \ge 1), \qquad \frac{b_{\text{eff}}}{b} = 1 \ (\beta < 1)bbeff​​=β2​−β21​(β≥1),bbeff​​=1 (β<1)

Result unit -

08Classical axial buckling stress of a cylindrical shell
σcr=E tr3(1−ν2)=0.605 E tr\sigma_{cr} = \frac{E\,t}{r\sqrt{3(1-\nu^2)}} = 0.605\,\frac{E\,t}{r}σcr​=r3(1−ν2)​Et​=0.605rEt​
SymbolDescriptionUnit
rrrShell radiusmm

Result unit MPa

Perfect shell; real shells 20–60 % of this. Use DNV-RP-C202.

09Eurocode 3 column buckling resistance (for comparison)
Nb,Rd=χ A fyγM1,λˉ=λ93.9 ε,ε=235/fyN_{b,Rd} = \frac{\chi\, A\, f_y}{\gamma_{M1}}, \qquad \bar\lambda = \frac{\lambda}{93.9\,\varepsilon}, \quad \varepsilon = \sqrt{235/f_y}Nb,Rd​=γM1​χAfy​​,λˉ=93.9ελ​,ε=235/fy​​
SymbolDescriptionUnit
χ\chiχReduction factor from buckling curve a0–d as a function of λ̄-
γM1\gamma_{M1}γM1​Partial factor (1.0 in EN 1993-1-1 recommended)-

Result unit N

Tables

Effective length factors K for columns

End conditionsTheoretical KRecommended design KShip example
Pinned – pinned1.01.0Pillar between decks with simple end connections
Fixed – fixed0.50.65Pillar with full-depth brackets top and bottom (rarely credited)
Fixed – pinned0.70.8Pillar bracketed at one end
Fixed – free (cantilever)2.02.1Mast, davit post, pedestal without top restraint
Fixed – translating (sway, rotation fixed)1.01.2Portal frame leg
Pinned – translating2.02.0Unbraced frame
Source: AISC Steel Construction Manual, Table C-A-7.1 (theoretical and recommended values); Gere & Timoshenko (1999) Ch. 11.

Plate buckling coefficient k for a simply supported plate under uniaxial compression

a/ba/ba/b (load along a)kkk (min over m)Half-waves m
0.5 (wide plate, load across short side)6.251
0.74.531
1.04.001
1.4144.50 → 4.00 transition1–2
2.04.002
3.04.003
≥ 1 (any), long plate4.00a/b
Source: Timoshenko & Gere, Theory of Elastic Stability, 2nd ed. (1961), Ch. 9; Hughes & Paik (2010) Ch. 12.

Clamped long edges: k ≈ 6.97. Unloaded edges one simply supported one free (flange outstand): k ≈ 0.425.

Elastic buckling and Johnson–Ostenfeld critical stress of mild-steel plating, k = 4, σ_y = 235 MPa

b/tb/tb/tβ\betaβσE\sigma_EσE​ [MPa]σcr\sigma_{cr}σcr​ (J–O) [MPa]σcr/σy\sigma_{cr}/\sigma_yσcr​/σy​
301.018282180.93
401.354662050.87
501.692981890.80
602.032071680.72
702.371521440.61
802.70116116 (elastic, σ_E < σ_y/2)0.50
1003.3874.574.50.32
Source: Computed from the formulas above (E = 206 000 MPa).

Examples

#01

Buckling check of a deck pillar

Worked example

Problem

A tubular pillar Ø 219.1 × 8.0 mm (hot-finished CHS, S235) is 3.00 m long between decks with simple end connections (K = 1.0) and carries a design axial load of 450 kN. Determine the slenderness, the Euler and Johnson–Ostenfeld critical stresses, the critical load, and the usage factor; compare with the Eurocode 3 buckling resistance (curve a).

Solution

Section (Example 2.6): A=5306A = 5306A=5306 mm², I=2.960×107I = 2.960 \times 10^7I=2.960×107 mm⁴, r=I/A=74.7r = \sqrt{I/A} = 74.7r=I/A​=74.7 mm.

Slenderness: λ=KL/r=3000/74.7=40.2\lambda = KL/r = 3000/74.7 = 40.2λ=KL/r=3000/74.7=40.2 (< λ_lim = 132 → inelastic range).

Euler stress: σE=π2×206 000/40.22=2.033×106/1616=1258\sigma_E = \pi^2 \times 206\,000/40.2^2 = 2.033 \times 10^6/1616 = 1258σE​=π2×206000/40.22=2.033×106/1616=1258 MPa (> σ_y/2 = 117.5).

Johnson–Ostenfeld: σcr=235 (1−235/(4×1258))=235×0.953=224\sigma_{cr} = 235\,(1 - 235/(4 \times 1258)) = 235 \times 0.953 = 224σcr​=235(1−235/(4×1258))=235×0.953=224 MPa; Pcr=224×5306=1189P_{cr} = 224 \times 5306 = 1189Pcr​=224×5306=1189 kN.

Applied stress: σ=450 000/5306=84.8\sigma = 450\,000/5306 = 84.8σ=450000/5306=84.8 MPa. Usage factor σ/σcr=0.38\sigma/\sigma_{cr} = 0.38σ/σcr​=0.38. With a permissible usage factor of 0.70 (indicative for pillars under operating loads — take the exact value from DNV Pt.3 Ch.6 or the governing standard): UC=0.38/0.70=0.54UC = 0.38/0.70 = 0.54UC=0.38/0.70=0.54 ✓.

Eurocode 3 comparison: ε=1.0\varepsilon = 1.0ε=1.0; λˉ=40.2/93.9=0.43\bar\lambda = 40.2/93.9 = 0.43λˉ=40.2/93.9=0.43; curve a → χ≈0.94\chi \approx 0.94χ≈0.94; Nb,Rd=0.94×5306×235/1.0=1172N_{b,Rd} = 0.94 \times 5306 \times 235/1.0 = 1172Nb,Rd​=0.94×5306×235/1.0=1172 kN — within 1.5 % of the Johnson–Ostenfeld value. Yield alone would allow 5306×235=12475306 \times 235 = 12475306×235=1247 kN; buckling reduces the capacity by only 5 % for this stocky pillar. A 6.0 m pillar of the same tube would have λ = 80.4, σ_E = 315 MPa, σ_cr = 191 MPa — an 18 % reduction.

#02

Elastic buckling of deck plating under hull girder compression

Worked example

Problem

Deck plating 10 mm, longitudinal stiffeners at 600 mm, frames at 2400 mm, mild steel. The hull girder sagging stress in the deck is 120 MPa (compression). Check the plate panel for buckling.

Solution

a/b=4⇒k=4.0a/b = 4 \Rightarrow k = 4.0a/b=4⇒k=4.0.

σE=0.904×4.0×206 000×(10/600)2=744 900×2.78×10−4=207 MPa\sigma_E = 0.904 \times 4.0 \times 206\,000 \times (10/600)^2 = 744\,900 \times 2.78 \times 10^{-4} = 207\ \text{MPa}σE​=0.904×4.0×206000×(10/600)2=744900×2.78×10−4=207 MPa

σE>σy/2\sigma_E > \sigma_y/2σE​>σy​/2 → Johnson–Ostenfeld: σcr=235 (1−235/(4×207))=235×0.716=168\sigma_{cr} = 235\,(1 - 235/(4 \times 207)) = 235 \times 0.716 = 168σcr​=235(1−235/(4×207))=235×0.716=168 MPa. Slenderness β=60235/206 000=2.03\beta = 60\sqrt{235/206\,000} = 2.03β=60235/206000​=2.03.

Usage: 120/168=0.71120/168 = 0.71120/168=0.71. Against a typical permissible usage factor of 0.8–0.9 for hull girder buckling of plating (sagging, deck) — take the exact factor from DNV Pt.3 Ch.8 / RP-C201 — the panel is acceptable with a modest margin. Note that AH36 plating of the same thickness would have the same σ_E = 207 MPa but σ_cr = 355(1 − 355/828) = 203 MPa: the higher yield helps only through the inelastic correction. Effective width after buckling (Faulkner): beff/b=2/2.03−1/2.032=0.985−0.243=0.74b_{\text{eff}}/b = 2/2.03 - 1/2.03^2 = 0.985 - 0.243 = 0.74beff​/b=2/2.03−1/2.032=0.985−0.243=0.74 — used in the ultimate hull girder strength (Section 7.3).

References

Timoshenko & Gere, Theory of Elastic Stability, 2nd ed. (1961)Clause Ch. 2 (Columns), Ch. 9 (Buckling of thin plates)Textbook
Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)Clause Ch. 12 (Elastic buckling of plates), Ch. 13 (Ultimate strength of plates), Ch. 14 (Stiffened panels)Textbook
DNV-RP-C201 Buckling strength of plated structuresClause Part 1 (Conventional buckling code — plates, stiffened panels, girders)Recommended

Referenced by DNV Rules Pt.3 Ch.8; confirm edition.

DNV-RP-C202 Buckling strength of shellsClause Sec. 3 (Unstiffened cylindrical shells)Recommended
EN 1993-1-1:2005 Eurocode 3 — Part 1-1Clause 6.3.1 (Buckling resistance of members in compression — buckling curves)Recommended
DNV Rules for Classification — Ships, Pt.3 Ch.6 (pillars) and Ch.8 (Buckling)Clause Pillar requirements; buckling acceptance criteriaMandatory

Confirm section numbering in the edition in force.

Previous · 2.9Plate bending under lateral pressureNext · 2.11Fatigue basics: S–N curves, stress ranges, Miner's rule

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Buckling as a stability problem
  • Euler column
  • Inelastic range — Johnson–Ostenfeld correction
  • Pillars in ships
  • Plate buckling (elastic)
  • Post-buckling and effective width
  • Stiffened panels and tripping
  • Shells
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Timoshenko & Gere, Theory of Elastic Stability, 2nd ed. (1961)

    Ch. 2 (Columns), Ch. 9 (Buckling of thin plates)

  • Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)

    Ch. 12 (Elastic buckling of plates), Ch. 13 (Ultimate strength of plates), Ch. 14 (Stiffened panels)

  • DNV-RP-C201 Buckling strength of plated structures

    Part 1 (Conventional buckling code — plates, stiffened panels, girders)

  • DNV-RP-C202 Buckling strength of shells

    Sec. 3 (Unstiffened cylindrical shells)

  • EN 1993-1-1:2005 Eurocode 3 — Part 1-1

    6.3.1 (Buckling resistance of members in compression — buckling curves)

  • DNV Rules for Classification — Ships, Pt.3 Ch.6 (pillars) and Ch.8 (Buckling)

    Pillar requirements; buckling acceptance criteria

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.