NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›1. Mathematics & Units›1.4 Areas, centroids and second moments of plane figures

Chapter 1 / Section 1.4

Areas, centroids and second moments of plane figures

Print this section

Definitions

For a plane area AAA with coordinates (x,z)(x, z)(x,z):

  • First moments: Qx=∫z dAQ_x = \int z\,dAQx​=∫zdA, Qz=∫x dAQ_z = \int x\,dAQz​=∫xdA; centroid zˉ=Qx/A\bar z = Q_x/Azˉ=Qx​/A, xˉ=Qz/A\bar x = Q_z/Axˉ=Qz​/A.
  • Second moments (moments of inertia of area): Ix=∫z2 dAI_x = \int z^2\,dAIx​=∫z2dA, Iz=∫x2 dAI_z = \int x^2\,dAIz​=∫x2dA; product of inertia Ixz=∫xz dAI_{xz} = \int x z\,dAIxz​=∫xzdA (zero when either axis is an axis of symmetry).
  • Polar moment: J=Ix+IzJ = I_x + I_zJ=Ix​+Iz​.
  • Radius of gyration: r=I/Ar = \sqrt{I/A}r=I/A​.

Parallel axis theorem

Ix′=Ixˉ+A d2I_{x'} = I_{\bar x} + A\,d^2Ix′​=Ixˉ​+Ad2

where IxˉI_{\bar x}Ixˉ​ is about the centroidal axis and ddd the distance between the parallel axes. The centroidal second moment is always the minimum. This theorem is the basis of every built-up section calculation (Section 2.5) and of the waterplane inertia about the LCF (Section 4.6).

Composite areas

  1. Divide into simple figures; tabulate: part, AiA_iAi​, zˉi\bar z_izˉi​, AizˉiA_i \bar z_iAi​zˉi​, Iown,iI_{\text{own},i}Iown,i​.
  2. zˉ=∑Aizˉi/∑Ai\bar z = \sum A_i \bar z_i / \sum A_izˉ=∑Ai​zˉi​/∑Ai​.
  3. INA=∑Iown,i+∑Ai(zˉi−zˉ)2I_{NA} = \sum I_{\text{own},i} + \sum A_i (\bar z_i - \bar z)^2INA​=∑Iown,i​+∑Ai​(zˉi​−zˉ)2.

Holes are included as negative areas. In ship sections, the table is usually built about the baseline and then shifted to the neutral axis with INA=IBL−A zˉ2I_{NA} = I_{BL} - A\,\bar z^2INA​=IBL​−Azˉ2 (Section 7.3).

Rotation of axes, principal axes

Ix′=Ix+Iz2+Ix−Iz2cos⁡2θ−Ixzsin⁡2θI_{x'} = \frac{I_x + I_z}{2} + \frac{I_x - I_z}{2}\cos 2\theta - I_{xz}\sin 2\thetaIx′​=2Ix​+Iz​​+2Ix​−Iz​​cos2θ−Ixz​sin2θ

Principal axes: tan⁡2θp=−2IxzIx−Iz\tan 2\theta_p = \dfrac{-2 I_{xz}}{I_x - I_z}tan2θp​=Ix​−Iz​−2Ixz​​; for symmetric ship sections the centreline and the horizontal neutral axis are principal. Unsymmetrical stiffeners (angles, bulb flats) bend about a principal axis inclined to the plate; the rule section modulus is nevertheless computed about the axis parallel to the plate (Section 2.5) because the plate restrains the stiffener.

Standard figures

See the table. The waterplane and section results used in hydrostatics (rectangle, triangle, semi-ellipse, parabola) are included because they give quick checks for barge-shaped hulls and for waterplane coefficients.

Formulas

01Centroid of a plane area
zˉ=∫z dAA=∑Ai zˉi∑Ai\bar z = \frac{\int z\,dA}{A} = \frac{\sum A_i\,\bar z_i}{\sum A_i}zˉ=A∫zdA​=∑Ai​∑Ai​zˉi​​
SymbolDescriptionUnit
zˉ\bar zzˉCentroid coordinatem
AiA_iAi​Area of part im²
zˉi\bar z_izˉi​Centroid of part im

Result unit m

02Second moment of area
Ix=∫z2 dAI_x = \int z^2\,dAIx​=∫z2dA
SymbolDescriptionUnit
IxI_xIx​Second moment about the x-axism⁴
zzzDistance from the x-axism

Result unit m⁴

03Parallel axis theorem
Ix′=Ixˉ+A d2I_{x'} = I_{\bar x} + A\,d^2Ix′​=Ixˉ​+Ad2
SymbolDescriptionUnit
IxˉI_{\bar x}Ixˉ​Second moment about the centroidal axism⁴
dddDistance between the two parallel axesm

Result unit m⁴

04Second moment of a composite about its neutral axis
INA=∑iIown,i+∑iAi(zˉi−zˉ)2=IBL−A zˉ2I_{NA} = \sum_i I_{\text{own},i} + \sum_i A_i\left(\bar z_i - \bar z\right)^2 = I_{BL} - A\,\bar z^2INA​=i∑​Iown,i​+i∑​Ai​(zˉi​−zˉ)2=IBL​−Azˉ2
SymbolDescriptionUnit
IBLI_{BL}IBL​Second moment about the reference (base) linem⁴

Result unit m⁴

05Polar moment and radius of gyration
J=Ix+Iz,r=IAJ = I_x + I_z, \qquad r = \sqrt{\frac{I}{A}}J=Ix​+Iz​,r=AI​​

Result unit m⁴, m

06Principal axes
tan⁡2θp=−2 IxzIx−Iz,I1,2=Ix+Iz2±(Ix−Iz2)2+Ixz2\tan 2\theta_p = \frac{-2\,I_{xz}}{I_x - I_z}, \qquad I_{1,2} = \frac{I_x + I_z}{2} \pm \sqrt{\left(\frac{I_x - I_z}{2}\right)^2 + I_{xz}^2}tan2θp​=Ix​−Iz​−2Ixz​​,I1,2​=2Ix​+Iz​​±(2Ix​−Iz​​)2+Ixz2​​
SymbolDescriptionUnit
IxzI_{xz}Ixz​Product of inertiam⁴
θp\theta_pθp​Angle of the principal axis from the x-axisrad

Result unit m⁴

Tables

Properties of plane figures (centroidal axes; b horizontal, h vertical)

FigureAreaCentroid (from base)III about horizontal centroidal axisIII about base
Rectangle b × hbhbhbhh/2h/2h/2bh3/12bh^3/12bh3/12bh3/3bh^3/3bh3/3
Triangle, base b, height hbh/2bh/2bh/2h/3h/3h/3bh3/36bh^3/36bh3/36bh3/12bh^3/12bh3/12
Trapezoid, parallel sides a (top), b (bottom), height h(a+b)h/2(a+b)h/2(a+b)h/2h(2a+b)3(a+b)\dfrac{h(2a+b)}{3(a+b)}3(a+b)h(2a+b)​h3(a2+4ab+b2)36(a+b)\dfrac{h^3(a^2+4ab+b^2)}{36(a+b)}36(a+b)h3(a2+4ab+b2)​—
Circle, diameter dπd2/4\pi d^2/4πd2/4d/2d/2d/2πd4/64\pi d^4/64πd4/64—
Hollow circle, d_o, d_iπ(do2−di2)/4\pi(d_o^2-d_i^2)/4π(do2​−di2​)/4do/2d_o/2do​/2π(do4−di4)/64\pi(d_o^4-d_i^4)/64π(do4​−di4​)/64—
Thin ring, mean radius r, thickness t2πrt2\pi r t2πrtrrrπr3t\pi r^3 tπr3t—
Semicircle, radius r (flat side as base)πr2/2\pi r^2/2πr2/24r/(3π)=0.4244 r4r/(3\pi) = 0.4244\,r4r/(3π)=0.4244r0.1098 r40.1098\,r^40.1098r4πr4/8\pi r^4/8πr4/8
Ellipse, semi-axes a (horizontal), b (vertical)πab\pi a bπabbbbπab3/4\pi a b^3/4πab3/4—
Parabolic segment, base b, height h (vertex at top)2bh/32bh/32bh/32h/52h/52h/58bh3/1758bh^3/1758bh3/1752bh3/72bh^3/72bh3/7
Rectangular waterplane L × B about centrelineLBLBLB—LB3/12LB^3/12LB3/12—
Triangular waterplane end, length ℓ, full base B, about its axis of symmetryℓB/2\ell B/2ℓB/2ℓ/3\ell/3ℓ/3 from baseℓB3/48\ell B^3/48ℓB3/48—
Source: Young, Budynas & Sadegh, Roark's Formulas for Stress and Strain, 8th ed. (2012), Appendix A; Gere & Timoshenko (1999), Appendix D.

Examples

#01

Waterplane of a barge with a triangular bow: area, LCF and transverse second moment

Worked example

Problem

A barge waterplane consists of a rectangle 40 m long × 12 m wide (stern end at x = 0) and an isosceles triangular bow of length 10 m on the full 12 m base. Find the waterplane area, the LCF from the stern, and ITI_TIT​ about the centreline.

Solution

Areas: rectangle 40×12=48040 \times 12 = 48040×12=480 m²; triangle 12×12×10=60\tfrac{1}{2} \times 12 \times 10 = 6021​×12×10=60 m². AWP=540A_{WP} = 540AWP​=540 m².

Centroids from the stern: rectangle 20 m; triangle 40+10/3=43.3340 + 10/3 = 43.3340+10/3=43.33 m.

LCF=480×20+60×43.33540=9600+2600540=22.59 m from the sternLCF = \frac{480 \times 20 + 60 \times 43.33}{540} = \frac{9600 + 2600}{540} = 22.59\ \text{m from the stern}LCF=540480×20+60×43.33​=5409600+2600​=22.59 m from the stern

ITI_TIT​ about the centreline (an axis of symmetry for both parts, so no parallel-axis terms):

IT=40×12312+10×12348=5760+360=6120 m4I_T = \frac{40 \times 12^3}{12} + \frac{10 \times 12^3}{48} = 5760 + 360 = 6120\ \text{m}^4IT​=1240×123​+4810×123​=5760+360=6120 m4

For a draught of 2.0 m and ∇=540×2.0×0.95=1026\nabla = 540 \times 2.0 \times 0.95 = 1026∇=540×2.0×0.95=1026 m³ (allowing for the bow taper below the waterline), BMT=6120/1026=5.96BM_T = 6120/1026 = 5.96BMT​=6120/1026=5.96 m — the typical very large metacentric radius of a shallow barge.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 12 (Review of centroids and moments of inertia) and Appendix DTextbook
Roark's Formulas for Stress and Strain, 8th ed. (2012)Clause Appendix A (Properties of sections)Textbook
Hibbeler, Mechanics of Materials, 10th ed. (2017)Clause Appendix A (Geometric properties of an area)Textbook
Previous · 1.3Numerical integration: trapezoidal and Simpson's rulesNext · 1.5Volumes and centroids of solids

Version 2 · last updated 20 Nov 2026 · Editor

On this page

  • Definitions
  • Parallel axis theorem
  • Composite areas
  • Rotation of axes, principal axes
  • Standard figures
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 12 (Review of centroids and moments of inertia) and Appendix D

  • Roark's Formulas for Stress and Strain, 8th ed. (2012)

    Appendix A (Properties of sections)

  • Hibbeler, Mechanics of Materials, 10th ed. (2017)

    Appendix A (Geometric properties of an area)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.