NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›1. Mathematics & Units›1.2 Unit conversion and dimensional consistency

Chapter 1 / Section 1.2

Unit conversion and dimensional consistency

Print this section

Conversion by chained factors

Multiply by ratios equal to one, writing every unit, and cancel:

15 kn×1852 m1 NM×1 h3600 s=7.717 m/s15\ \text{kn} \times \frac{1852\ \text{m}}{1\ \text{NM}} \times \frac{1\ \text{h}}{3600\ \text{s}} = 7.717\ \text{m/s}15 kn×1 NM1852 m​×3600 s1 h​=7.717 m/s

Never convert in your head for anything that enters a design file; write the chain.

Dimensional homogeneity

Every term of an equation must have the same dimensions. Use this as the first check of any formula copied from a rule or paper:

  • Δ=ρ ∇\Delta = \rho\,\nablaΔ=ρ∇: [t] = [t/m³]·[m³] ✓
  • TPC=ρ AWP/100TPC = \rho\,A_{WP}/100TPC=ρAWP​/100: [t/cm] = [t/m³]·[m²]/100 — the 100 carries the unit [cm/m]; such dimensional constants must be stated with the formula (Section 4.8).
  • MCT1cm=Δ GML/(100 L)MCT1cm = \Delta\,GM_L/(100\,L)MCT1cm=ΔGML​/(100L): [t·m/cm] = [t]·[m]/(100·[m]) ✓ with 100 [cm/m].
  • Rule formulas often mix units deliberately: e.g. DNV scantling formulas take sss in mm, lll in m, ppp in kN/m² and give ttt in mm — the coefficients absorb the conversion. Use exactly the units the rule states.

Mass vs force, mass moments vs force moments

In stability, Δ\DeltaΔ [t], moments w⋅dw\cdot dw⋅d [t·m] and GZGZGZ [m] are consistent as long as all are mass-based; the righting moment in kN·m is Δ g GZ\Delta\,g\,GZΔgGZ. In structural analysis, loads must be forces: a 10 t crane load is 98.1 kN98.1\ \text{kN}98.1 kN. Mixing "t" as a force (tonne-force) with kN is the most common unit error in load tables received from suppliers — always ask whether a quoted "t" is mass or force.

Pressure units in different disciplines

  • Hydrostatics and sea loads: kPa (kN/m²). Sea pressure at 5.5 m draught: 1.025×9.81×5.5=55.31.025 \times 9.81 \times 5.5 = 55.31.025×9.81×5.5=55.3 kPa.
  • Structural stress: MPa (N/mm²). 1 MPa=1000 kPa1\ \text{MPa} = 1000\ \text{kPa}1 MPa=1000 kPa.
  • Hydraulics and tank test pressures: bar. 2.5 bar=250 kPa=0.25 MPa=25.52.5\ \text{bar} = 250\ \text{kPa} = 0.25\ \text{MPa} = 25.52.5 bar=250 kPa=0.25 MPa=25.5 m FW head.
  • Material data sheets (US): ksi, psi.

Angular units

Degrees for reporting heel, trim angle, rudder angle; radians inside every formula with trigonometric series, integration of GZ curves (m·rad), rotational stiffness and vibration (ω=2πf\omega = 2\pi fω=2πf). A GZ-curve area of 0.090 m·rad is 5.16 m·deg.

Checklist before accepting a number from another source

  1. Identify the unit of every input (ask if not stated).
  2. Mass or force? Gauge or absolute pressure? Moulded or extreme dimension? Gross or net thickness?
  3. Convert to the handbook's SI set with a written chain.
  4. Check the order of magnitude against a known value (e.g. sea pressure ≈ 10 kPa per metre of depth; steel plate 10 mm weighs 78.5 kg/m²).

Formulas

01Conversion by unit ratios
x [unit2]=x [unit1]×1 unit2-equivalent1 unit1x\,[\text{unit}_2] = x\,[\text{unit}_1] \times \frac{1\ \text{unit}_2\text{-equivalent}}{1\ \text{unit}_1}x[unit2​]=x[unit1​]×1 unit1​1 unit2​-equivalent​

Result unit -

Each ratio equals one; write the units and cancel.

02Sea pressure at depth
p=ρSW g z=10.06 z[kPa, z in m]p = \rho_{SW}\, g\, z = 10.06\, z \quad [\text{kPa, } z \text{ in m}]p=ρSW​gz=10.06z[kPa, z in m]
SymbolDescriptionUnit
zzzDepth below the still waterlinem

Result unit kPa

03Mass moment to force moment
M [kN⋅m]=g×M [t⋅m]=9.81×M [t⋅m]M\,[\text{kN·m}] = g \times M\,[\text{t·m}] = 9.81 \times M\,[\text{t·m}]M[kN⋅m]=g×M[t⋅m]=9.81×M[t⋅m]

Result unit kN·m

04Steel plate mass per unit area
m′=ρst t=7.85 t[kg/m2, t in mm]m' = \rho_{st}\, t = 7.85\, t \quad [\text{kg/m}^2,\ t \text{ in mm}]m′=ρst​t=7.85t[kg/m2, t in mm]
SymbolDescriptionUnit
tttPlate thicknessmm

Result unit kg/m²

Tables

Quick equivalents for order-of-magnitude checks

QuantityRule of thumb
Sea pressure≈ 10 kPa per metre of depth
Steel plate7.85 kg/m² per mm of thickness; 10 mm plate = 78.5 kg/m²
Steel density7.85 t/m³ ≈ 7.7 × seawater
1 t of seawater0.976 m³; 1 m³ of seawater = 1.025 t
1 knot≈ 0.5 m/s ≈ 1.85 km/h
1 bar≈ 10 m of water head ≈ 14.5 psi
1 MPa≈ 10 bar ≈ 145 psi ≈ 0.102 kgf/mm²
1 kN≈ 102 kgf (the weight of 102 kg)
Yield of mild steel235 MPa ≈ 24 kgf/mm² ≈ 34 ksi
1 m·rad57.3 m·deg
Source: Derived from the exact factors in Section 1.1.

Examples

#01

Converting a supplier's load table

Worked example

Problem

A winch supplier states: 'Pull 25 t, brake holding load 40 t, mass 12.5 t, hydraulic pressure 280 bar, max line speed 60 m/min'. Convert to the handbook's units for a foundation calculation.

Solution

Pull and brake load are forces (tonne-force): 25×9.81=245 kN25 \times 9.81 = 245\ \text{kN}25×9.81=245 kN; 40×9.81=392 kN40 \times 9.81 = 392\ \text{kN}40×9.81=392 kN. Mass 12.5 t is a mass: weight =12.5×9.81=122.6 kN= 12.5 \times 9.81 = 122.6\ \text{kN}=12.5×9.81=122.6 kN. Pressure 280 bar=28.0 MPa=28 000 kPa280\ \text{bar} = 28.0\ \text{MPa} = 28\,000\ \text{kPa}280 bar=28.0 MPa=28000 kPa. Speed 60/60=1.00 m/s60/60 = 1.00\ \text{m/s}60/60=1.00 m/s. Design horizontal load on the foundation (brake case) =392 kN= 392\ \text{kN}=392 kN plus dynamic factor per the governing standard; vertical load =122.6 kN= 122.6\ \text{kN}=122.6 kN plus the vertical component of the line pull if the lead is inclined. Record in the calculation: 'Loads from supplier data sheet, tonnes interpreted as tonne-force, confirmed with supplier on <date>'.

References

NIST Special Publication 811 (2008) Guide for the Use of the International System of UnitsClause Ch. 7 (Rules and style conventions), Appendix B (Conversion factors)Recommended

Free download from nist.gov.

DNV Rules for Classification — Ships, Pt.3 Ch.1 Sec.4Clause Symbols and units used in rule formulasMandatory

Rule formulas use mixed units (mm, m, kN/m²) by design; use exactly those stated.

Previous · 1.1SI units and maritime units (tonne, knot, nautical mile, bar)Next · 1.3Numerical integration: trapezoidal and Simpson's rules

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Conversion by chained factors
  • Dimensional homogeneity
  • Mass vs force, mass moments vs force moments
  • Pressure units in different disciplines
  • Angular units
  • Checklist before accepting a number from another source
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • NIST Special Publication 811 (2008) Guide for the Use of the International System of Units

    Ch. 7 (Rules and style conventions), Appendix B (Conversion factors)

  • DNV Rules for Classification — Ships, Pt.3 Ch.1 Sec.4

    Symbols and units used in rule formulas

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.