NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.5 Section properties of built-up sections (stiffener + plate)

Chapter 2 / Section 2.5

Section properties of built-up sections (stiffener + plate)

Print this section

Why the plate belongs to the stiffener

A stiffener welded to plating bends together with a strip of the plate. The design section is therefore stiffener + attached plate flange; the stiffener alone has a much smaller modulus and would give a grossly conservative (wrong) stress. The neutral axis of the combined section lies close to the plate, so the flange of the stiffener is the highly stressed fibre and the plate fibre is lightly stressed.

Effective breadth of the attached plate

  • Stiffeners (secondary members): classification rules take the attached plate breadth equal to the stiffener spacing sss for the section modulus check (DNV Rules Pt.3 Ch.3 — effective flange of secondary stiffeners; confirm the clause in the edition in force). Some rules limit it to a multiple of the plate thickness for very wide spacings.
  • Girders and web frames (primary members): shear lag reduces the effective flange. The effective breadth beb_ebe​ depends on the ratio of the girder span to the flange width and on the load type; classification rules give be/bb_e/bbe​/b curves (Schade curves); a common first estimate is be≈min⁡(b, ℓg/5)b_e \approx \min(b,\ \ell_g/5)be​≈min(b, ℓg​/5) for a girder under distributed load, where ℓg\ell_gℓg​ is the span and bbb the sum of half-spacings to the neighbouring girders. Hughes & Paik Ch. 9 gives the theory.
  • Buckling: when the plate is in compression (e.g. deck plating under hogging), the effective width for stiffness is further reduced to the post-buckling effective width beffb_{\text{eff}}beff​ (Section 2.10 and DNV-RP-C201).

Calculation procedure (tabular)

  1. Reference axis: the outer face of the plate (or the plate mid-plane). Tabulate for each part iii: AiA_iAi​, ziz_izi​ (centroid height), AiziA_i z_iAi​zi​, Aizi2A_i z_i^2Ai​zi2​, Iown,i=bihi3/12I_{\text{own},i} = b_i h_i^3/12Iown,i​=bi​hi3​/12.
  2. Neutral axis height zˉ=∑Aizi/∑Ai\bar z = \sum A_i z_i / \sum A_izˉ=∑Ai​zi​/∑Ai​.
  3. INA=∑Iown,i+∑Aizi2−zˉ2∑AiI_{NA} = \sum I_{\text{own},i} + \sum A_i z_i^2 - \bar z^2 \sum A_iINA​=∑Iown,i​+∑Ai​zi2​−zˉ2∑Ai​.
  4. Section moduli: Wflange=INA/(htotal−zˉ)W_{\text{flange}} = I_{NA}/(h_{\text{total}} - \bar z)Wflange​=INA​/(htotal​−zˉ) and Wplate=INA/zˉW_{\text{plate}} = I_{NA}/\bar zWplate​=INA​/zˉ. The flange value governs.
  5. Shear area: Aw=hwtwA_w = h_w t_wAw​=hw​tw​ (web only).
  6. Report in cm³ and cm⁴ for comparison with rule requirements.

Rolled profiles

For a bulb flat (HP) or angle, take AAA, own III and centroid height from the manufacturer's table and treat the profile as one "part" in the table above. Angles and bulb flats are unsymmetrical; the rule modulus is nevertheless taken about the axis parallel to the plate because the plate prevents lateral deflection; lateral-torsional (tripping) behaviour is checked separately (Section 2.10).

Corrosion addition

Rule section moduli are compared on the net section (gross scantlings minus the corrosion addition tct_ctc​ on every plate element) in current DNV rules; older rules compared gross scantlings against a requirement that included the allowance. Always state which basis is used (Section 3.8).

Quick estimate

For a T- or angle-stiffener with attached plate, the combined modulus to the flange is roughly 1.6–2.5 times the modulus of the profile alone, and the neutral axis lies at 15–30 % of the stiffener height above the plate. Use only for sanity checks.

Formulas

01Neutral axis of a built-up section
zˉ=∑iAi zi∑iAi\bar z = \frac{\sum_i A_i\, z_i}{\sum_i A_i}zˉ=∑i​Ai​∑i​Ai​zi​​
SymbolDescriptionUnit
AiA_iAi​Area of element i (plate flange, web, face plate)mm²
ziz_izi​Height of the centroid of element i above the reference linemm

Result unit mm

02Second moment of area about the neutral axis
INA=∑i(bihi312+Aizi2)−zˉ2∑iAiI_{NA} = \sum_i \left(\frac{b_i h_i^3}{12} + A_i z_i^2\right) - \bar z^2 \sum_i A_iINA​=i∑​(12bi​hi3​​+Ai​zi2​)−zˉ2i∑​Ai​
SymbolDescriptionUnit
bi,hib_i, h_ibi​,hi​Width and height (in the bending direction) of rectangular element imm

Result unit mm⁴

Divide by 10⁴ for cm⁴.

03Section moduli to the flange and to the plate
Wflange=INAh−zˉ,Wplate=INAzˉW_{\text{flange}} = \frac{I_{NA}}{h - \bar z}, \qquad W_{\text{plate}} = \frac{I_{NA}}{\bar z}Wflange​=h−zˉINA​​,Wplate​=zˉINA​​
SymbolDescriptionUnit
hhhTotal depth from the reference line to the top of the face platemm

Result unit mm³

The smaller (flange) value governs the stress check. Divide by 10³ for cm³.

04Effective plate flange (secondary stiffeners)
beff=s(class rule convention for stiffener section modulus)b_{\text{eff}} = s \quad (\text{class rule convention for stiffener section modulus})beff​=s(class rule convention for stiffener section modulus)
SymbolDescriptionUnit
sssStiffener spacingmm

Result unit mm

Confirm in the rule set in force (DNV Pt.3 Ch.3). For primary members use shear-lag effective breadth.

05Effective breadth of a girder flange (first estimate)
be≈min⁡(b, ℓg5)b_e \approx \min\left(b,\ \frac{\ell_g}{5}\right)be​≈min(b, 5ℓg​​)
SymbolDescriptionUnit
bbbSum of half-spacings to adjacent girdersm
ℓg\ell_gℓg​Girder span between supportsm

Result unit m

Indicative; use the Schade-type curves in the class rules (DNV Pt.3 Ch.3) for approval work.

06Shear area of a stiffener
Aw=hw twA_w = h_w\, t_wAw​=hw​tw​

Result unit mm² (rules: cm²)

Tables

Tabular calculation template for a built-up section (reference line = outer face of plate)

Elementbbb [mm]hhh [mm]A=bhA = bhA=bh [mm²]zzz [mm]AzA zAz [mm³]Az2A z^2Az2 [mm⁴]Iown=bh3/12I_{own} = bh^3/12Iown​=bh3/12 [mm⁴]
Attached plate (b = s)st_ps·t_pt_p/2……s·t_p³/12
Webt_wh_wt_w·h_wt_p + h_w/2……t_w·h_w³/12
Face plate (flange)b_ft_fb_f·t_ft_p + h_w + t_f/2……b_f·t_f³/12
ΣΣAΣAzΣAz²ΣI_own
Resultsz̄ = ΣAz/ΣAI_NA = ΣI_own + ΣAz² − z̄²·ΣAW_fl = I_NA/(h − z̄)W_pl = I_NA/z̄
Source: Standard procedure; Hughes & Paik (2010) Ch. 9; DNV Rules Pt.3 Ch.3 (effective flange).

Examples

#01

Section modulus of the deck T-stiffener with attached plate

Worked example

Problem

Deck plating 10 mm, stiffener spacing 600 mm. Built-up T-stiffener: web 200 × 10 mm, face plate 80 × 12 mm. Compute the neutral axis, INAI_{NA}INA​, the section moduli to the flange and to the plate, and the shear area. Compare with the profile alone.

Solution

Reference line: outer face of the plate. Attached plate breadth = s = 600 mm.

ElementbhA [mm²]z [mm]A z [mm³]A z² [mm⁴]I_own [mm⁴]
Plate600106000530 000150 00050 000
Web102002000110220 00024 200 0006 666 667
Flange8012960216207 36044 789 76011 520
Σ8960457 36069 139 7606 728 187
zˉ=457 3608960=51.0 mm above the plate face\bar z = \frac{457\,360}{8960} = 51.0\ \text{mm above the plate face}zˉ=8960457360​=51.0 mm above the plate face INA=6 728 187+69 139 760−51.042×8960=75 867 947−23 341 000=52.53×106 mm4=5253 cm4I_{NA} = 6\,728\,187 + 69\,139\,760 - 51.04^2 \times 8960 = 75\,867\,947 - 23\,341\,000 = 52.53 \times 10^6\ \text{mm}^4 = 5253\ \text{cm}^4INA​=6728187+69139760−51.042×8960=75867947−23341000=52.53×106 mm4=5253 cm4

Total depth h=10+200+12=222h = 10 + 200 + 12 = 222h=10+200+12=222 mm.

Wflange=52.53×106222−51.0=307 200 mm3=307 cm3,Wplate=52.53×10651.0=1 029 000 mm3=1029 cm3W_{\text{flange}} = \frac{52.53 \times 10^6}{222 - 51.0} = 307\,200\ \text{mm}^3 = 307\ \text{cm}^3, \qquad W_{\text{plate}} = \frac{52.53 \times 10^6}{51.0} = 1\,029\,000\ \text{mm}^3 = 1029\ \text{cm}^3Wflange​=222−51.052.53×106​=307200 mm3=307 cm3,Wplate​=51.052.53×106​=1029000 mm3=1029 cm3

Shear area Aw=200×10=20.0A_w = 200 \times 10 = 20.0Aw​=200×10=20.0 cm².

Profile alone (web + flange, Section 2.4 table): I=1397I = 1397I=1397 cm⁴, neutral axis 134.4 mm above the web foot, WWW to the flange tip =1397/(212−134.4)×10=180= 1397/(212 - 134.4) \times 10 = 180=1397/(212−134.4)×10=180 cm³. The attached plate raises the flange modulus by 70 % (307 vs 180 cm³) and the inertia by a factor 3.8 — which is why the stiffener must never be checked alone. The neutral axis sits at 51 mm, i.e. 23 % of the stiffener height above the plate, within the quick-estimate range.

References

Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)Clause Ch. 9 (Stiffened panels — effective breadth, shear lag, section properties)Textbook
DNV Rules for Classification — Ships, Pt.3 Ch.3 (Structural design principles)Clause Sec. on effective flange of stiffeners and girders; net scantling approachMandatory

Confirm section numbering in the edition in force.

Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)Clause Vol. 1, Ch. 7 (Structural design and analysis — section modulus of stiffeners with plating)Textbook
Previous · 2.4Bending stress and section modulus of beamsNext · 2.6Deflection of beams (standard cases, superposition)

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Why the plate belongs to the stiffener
  • Effective breadth of the attached plate
  • Calculation procedure (tabular)
  • Rolled profiles
  • Corrosion addition
  • Quick estimate
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)

    Ch. 9 (Stiffened panels — effective breadth, shear lag, section properties)

  • DNV Rules for Classification — Ships, Pt.3 Ch.3 (Structural design principles)

    Sec. on effective flange of stiffeners and girders; net scantling approach

  • Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)

    Vol. 1, Ch. 7 (Structural design and analysis — section modulus of stiffeners with plating)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.