NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.6 Deflection of beams (standard cases, superposition)

Chapter 2 / Section 2.6

Deflection of beams (standard cases, superposition)

Print this section

Governing equation

For small deflections of an elastic beam (Euler–Bernoulli):

EId2wdx2=−M(x)(sagging positive, w positive downward),EI w′′′′=q(x)E I \frac{d^2 w}{dx^2} = -M(x) \quad\text{(sagging positive, } w \text{ positive downward)}, \qquad EI\,w'''' = q(x)EIdx2d2w​=−M(x)(sagging positive, w positive downward),EIw′′′′=q(x)

Integrate twice with the boundary conditions (deflection and slope zero at a fixed end; deflection and moment zero at a simple support; shear and moment zero at a free end). Shear deformation adds ws≈∫V/(GAs) dxw_s \approx \int V/(G A_s)\,dxws​≈∫V/(GAs​)dx — negligible for span/depth > 10, significant for short deep girders and sandwich panels (Section 3.6).

Standard cases

The maximum deflections of the common cases are in the table of Section 2.3. The most used:

  • Simply supported, UDL: δ=5 q L4384 EI\delta = \dfrac{5\,q\,L^4}{384\,EI}δ=384EI5qL4​
  • Fixed ends, UDL: δ=q L4384 EI\delta = \dfrac{q\,L^4}{384\,EI}δ=384EIqL4​ (one fifth of the simply supported value)
  • Cantilever, point load at tip: δ=P L33 EI\delta = \dfrac{P\,L^3}{3\,EI}δ=3EIPL3​
  • Simply supported, central point load: δ=P L348 EI\delta = \dfrac{P\,L^3}{48\,EI}δ=48EIPL3​

Superposition

For linear elastic structures, deflections from several loads add. Combine standard cases (UDL + point load; load + end moment) instead of integrating from scratch. Statically indeterminate beams: release a redundant support, compute the deflection there from the loads, and add the deflection from the unknown reaction; set the sum to zero (compatibility) and solve.

Macaulay's method

Write M(x)M(x)M(x) with step functions ⟨x−a⟩n\langle x - a\rangle^n⟨x−a⟩n (zero for x<ax < ax<a) so that one expression covers the whole span; integrate as a polynomial. Efficient for beams with several point loads (e.g. a shaft with several bearings, a girder with pillars).

Energy methods

Castigliano: δP=∂U/∂P\delta_P = \partial U/\partial PδP​=∂U/∂P with U=∫M2/(2EI) dxU = \int M^2/(2EI)\,dxU=∫M2/(2EI)dx; unit-load method: δ=∫M m/(EI) dx\delta = \int M\,m/(EI)\,dxδ=∫Mm/(EI)dx. Useful for frames and curved members (davits, A-frames).

Deflection limits (serviceability)

Deflection seldom governs ship primary structure (rules control stress and buckling) but it governs: machinery seatings and shaft alignment (bearing offsets of ~0.1 mm matter), crane pedestals and slew rings (manufacturer limits on out-of-flatness and tilt, often ≤ 1 mrad), hatch covers and large openings (sealing), accommodation decks (vibration and perceived stiffness), and sandwich/FRP panels. Typical limits used in practice: L/150L/150L/150–L/200L/200L/200 for deck plating under local loads, L/250L/250L/250–L/400L/400L/400 for girders carrying equipment, stricter per supplier for shaft lines and slew rings.

Flexural rigidity and stiffness

EIEIEI is the only material-and-geometry parameter in deflection. Replacing mild steel by high-strength steel does not reduce deflection (same EEE); replacing steel by aluminium triples it for the same section. Stiffness k=P/δk = P/\deltak=P/δ (e.g. 48EI/L348EI/L^348EI/L3 for a central point load) is used in vibration estimates (f=12πk/mf = \dfrac{1}{2\pi}\sqrt{k/m}f=2π1​k/m​) — Section 9.10.

Formulas

01Euler–Bernoulli beam equation
EI d2wdx2=−M(x),EI d4wdx4=q(x)EI\,\frac{d^2 w}{dx^2} = -M(x), \qquad EI\,\frac{d^4 w}{dx^4} = q(x)EIdx2d2w​=−M(x),EIdx4d4w​=q(x)
SymbolDescriptionUnit
wwwDeflection (positive downward)mm
EIEIEIFlexural rigidityN·mm²

Result unit mm

02Simply supported beam, UDL — maximum deflection
δmax⁡=5 q L4384 EI\delta_{\max} = \frac{5\,q\,L^4}{384\,EI}δmax​=384EI5qL4​
SymbolDescriptionUnit
qqqUniformly distributed loadN/mm
LLLSpanmm

Result unit mm

03Fixed-ended beam, UDL — maximum deflection
δmax⁡=q L4384 EI\delta_{\max} = \frac{q\,L^4}{384\,EI}δmax​=384EIqL4​

Result unit mm

04Cantilever, tip load — tip deflection and slope
δ=P L33 EI,θ=P L22 EI\delta = \frac{P\,L^3}{3\,EI}, \qquad \theta = \frac{P\,L^2}{2\,EI}δ=3EIPL3​,θ=2EIPL2​
SymbolDescriptionUnit
PPPPoint load at the tipN
θ\thetaθSlope at the tiprad

Result unit mm

05Simply supported beam, central point load
δmax⁡=P L348 EI\delta_{\max} = \frac{P\,L^3}{48\,EI}δmax​=48EIPL3​

Result unit mm

06Unit-load (virtual work) method
δ=∫0LM(x) m(x)EI dx\delta = \int_0^L \frac{M(x)\,m(x)}{EI}\,dxδ=∫0L​EIM(x)m(x)​dx
SymbolDescriptionUnit
M(x)M(x)M(x)Moment from the actual loadsN·mm
m(x)m(x)m(x)Moment from a unit load at the point and in the direction of the required deflectionmm

Result unit mm

07Beam stiffness and natural frequency (lumped mass)
k=Pδ,fn=12πkmk = \frac{P}{\delta}, \qquad f_n = \frac{1}{2\pi}\sqrt{\frac{k}{m}}k=δP​,fn​=2π1​mk​​
SymbolDescriptionUnit
kkkStiffnessN/m
mmmEffective masskg
fnf_nfn​Natural frequencyHz

Result unit Hz

Tables

Indicative deflection limits used in ship and offshore practice

ElementLimit (span L)Governing concernSource
Deck/bulkhead plating between stiffeners under local loadL/100 – L/150Appearance, coating crackingPractice; not a rule limit
Secondary stiffenersL/150 – L/200ServiceabilityPractice
Deck girders carrying equipmentL/250 – L/400Equipment alignmentPractice; supplier
Crane pedestal top flange (slew ring)Flatness ≤ 0.5–1.0 mm; tilt ≤ 1 mrad under load (typical)Slew bearing lifeCrane maker; DNV-ST-0378 refers to maker's limits
Engine seating / shaft lineBearing offsets per alignment calculation (0.1 mm order)Shaft alignmentEngine/shaft maker; class alignment calculation
Hatch coversL/300 – L/500 (sealing)WeathertightnessHatch cover maker
Sandwich/FRP panels (small craft)L/100 – L/200Core shear, appearanceISO 12215-5 (stiffness criteria for panels)
Source: Compiled from practice and the cited documents; limits are serviceability guidance, not class strength requirements — confirm with the equipment supplier and the Administration.

Examples

#01

Deflection of the deck stiffener

Worked example

Problem

The T-stiffener with plate of Example 2.5 (INA=5253I_{NA} = 5253INA​=5253 cm⁴ =52.53×106= 52.53 \times 10^6=52.53×106 mm⁴) spans 2.40 m under q=15.0q = 15.0q=15.0 kN/m. Find the midspan deflection for fixed ends and for simple supports.

Solution

q=15.0q = 15.0q=15.0 kN/m =15.0= 15.0=15.0 N/mm; L=2400L = 2400L=2400 mm; EI=206 000×52.53×106=1.082×1013EI = 206\,000 \times 52.53 \times 10^6 = 1.082 \times 10^{13}EI=206000×52.53×106=1.082×1013 N·mm². L4=3.318×1013L^4 = 3.318 \times 10^{13}L4=3.318×1013 mm⁴.

Fixed ends: δ=15.0×3.318×1013384×1.082×1013=4.977×10144.155×1015=0.120\delta = \dfrac{15.0 \times 3.318 \times 10^{13}}{384 \times 1.082 \times 10^{13}} = \dfrac{4.977 \times 10^{14}}{4.155 \times 10^{15}} = 0.120δ=384×1.082×101315.0×3.318×1013​=4.155×10154.977×1014​=0.120 mm =L/20 000= L/20\,000=L/20000.

Simply supported: δ=5×0.120=0.599\delta = 5 \times 0.120 = 0.599δ=5×0.120=0.599 mm =L/4000= L/4000=L/4000.

Both are negligible against any serviceability limit; deck stiffeners under uniform pressure are stress- (and buckling-) governed, not deflection-governed.

#02

Davit arm: stress and deflection governed check

Worked example

Problem

A davit arm is a cantilever tube Ø 219.1 × 8.0 mm (CHS), length 3.0 m, with a working load of 15 kN at the tip (including dynamic factor). Steel S235. Check bending stress against 0.8 σ_y and tip deflection against L/150.

Solution

Section: A=π4(219.12−203.12)=5306A = \tfrac{\pi}{4}(219.1^2 - 203.1^2) = 5306A=4π​(219.12−203.12)=5306 mm²; I=π64(219.14−203.14)=2.960×107I = \tfrac{\pi}{64}(219.1^4 - 203.1^4) = 2.960 \times 10^7I=64π​(219.14−203.14)=2.960×107 mm⁴; W=I/(219.1/2)=2.702×105W = I/(219.1/2) = 2.702 \times 10^5W=I/(219.1/2)=2.702×105 mm³.

Moment at the root: M=15×3.0=45.0M = 15 \times 3.0 = 45.0M=15×3.0=45.0 kN·m. σ=45.0×106/2.702×105=166.5\sigma = 45.0 \times 10^6/2.702 \times 10^5 = 166.5σ=45.0×106/2.702×105=166.5 MPa; allowable 0.8×235=1880.8 \times 235 = 1880.8×235=188 MPa → UC=0.89UC = 0.89UC=0.89 (pass, small margin).

Tip deflection: δ=15 000×300033×206 000×2.960×107=4.05×10141.829×1013=22.1\delta = \dfrac{15\,000 \times 3000^3}{3 \times 206\,000 \times 2.960 \times 10^7} = \dfrac{4.05 \times 10^{14}}{1.829 \times 10^{13}} = 22.1δ=3×206000×2.960×10715000×30003​=1.829×10134.05×1014​=22.1 mm =L/136= L/136=L/136 — exceeds L/150=20L/150 = 20L/150=20 mm.

Here deflection governs: a stiffer tube (Ø 244.5 × 8, I=4.16×107I = 4.16 \times 10^7I=4.16×107 mm⁴, δ=15.8\delta = 15.8δ=15.8 mm = L/190) is required even though the stress check passes. For lifting appliances the governing standard (e.g. DNV-ST-0378 for offshore cranes, or the Administration's LSA requirements for lifeboat davits) sets the load factors and allowables; the figures here illustrate the method only.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 9 (Deflections of beams: integration, superposition, Macaulay), Ch. 10 (Statically indeterminate beams), Appendix G (Deflections and slopes of beams)Textbook
Roark's Formulas for Stress and Strain, 8th ed. (2012)Clause Table 8.1 (Beams — shear, moment, slope and deflection formulas)Textbook
Hibbeler, Mechanics of Materials, 10th ed. (2017)Clause Ch. 12 (Deflection of beams and shafts), Ch. 14 (Energy methods)Textbook
Previous · 2.5Section properties of built-up sections (stiffener + plate)Next · 2.7Shear stress and torsion

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Governing equation
  • Standard cases
  • Superposition
  • Macaulay's method
  • Energy methods
  • Deflection limits (serviceability)
  • Flexural rigidity and stiffness
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 9 (Deflections of beams: integration, superposition, Macaulay), Ch. 10 (Statically indeterminate beams), Appendix G (Deflections and slopes of beams)

  • Roark's Formulas for Stress and Strain, 8th ed. (2012)

    Table 8.1 (Beams — shear, moment, slope and deflection formulas)

  • Hibbeler, Mechanics of Materials, 10th ed. (2017)

    Ch. 12 (Deflection of beams and shafts), Ch. 14 (Energy methods)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.