NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.4 Bending stress and section modulus of beams

Chapter 2 / Section 2.4

Bending stress and section modulus of beams

Print this section

Flexure formula

For a beam in pure bending about a principal axis, plane sections remain plane and the normal stress varies linearly from the neutral axis:

σ(z)=M zI,σmax⁡=MW,W=Izmax⁡\sigma(z) = \frac{M\,z}{I}, \qquad \sigma_{\max} = \frac{M}{W}, \qquad W = \frac{I}{z_{\max}}σ(z)=IMz​,σmax​=WM​,W=zmax​I​

III is the second moment of area about the neutral axis (which passes through the centroid for pure bending of a homogeneous section) and WWW (also ZZZ or SSS) the section modulus. For an unsymmetrical section there are two section moduli — to the top fibre and to the bottom fibre — and the smaller governs the stress check; in a stiffener-plate combination the flange modulus is the smaller (Section 2.5).

Units in rule formulas

Classification rules give the required section modulus in cm³ and the inertia in cm⁴, with spans in m, spacing in mm and pressures in kN/m²: a typical form is Z=C s ℓ2 pσ [cm3]Z = \dfrac{C\,s\,\ell^2\,p}{\sigma}\ [\text{cm}^3]Z=σCsℓ2p​ [cm3] where the constant CCC absorbs the unit conversions and the end-fixity coefficient. Convert consistently: 1 cm3=103 mm31\ \text{cm}^3 = 10^3\ \text{mm}^31 cm3=103 mm3, 1 cm4=104 mm41\ \text{cm}^4 = 10^4\ \text{mm}^41 cm4=104 mm4.

Shear stress in beams

τ(z)=V Q(z)I b(z)\tau(z) = \frac{V\,Q(z)}{I\,b(z)}τ(z)=Ib(z)VQ(z)​

with QQQ the first moment of the area beyond zzz and bbb the width at zzz. For I- and T-sections the web carries practically all the shear; the engineering approximation τ≈V/Aweb\tau \approx V/A_{\text{web}}τ≈V/Aweb​ (with Aweb=hwtwA_{\text{web}} = h_w t_wAweb​=hw​tw​) is used in class rules as the shear area requirement. For a rectangle τmax⁡=1.5 V/A\tau_{\max} = 1.5\,V/Aτmax​=1.5V/A; for a solid circle 4V/(3A)4V/(3A)4V/(3A); for a thin-walled tube 2V/A2V/A2V/A.

Composite (two-material) beams

Transform the stiffer material by the modular ratio n=E1/E2n = E_1/E_2n=E1​/E2​ (multiply widths by nnn); compute III of the transformed section; stresses in material 1 are multiplied back by nnn. Used for aluminium superstructures on steel hulls (with a flexible joint the superstructure is often excluded from the hull girder), for FRP sandwich (Section 3.6) and for steel inserts in aluminium craft.

Curved and deep beams

The flexure formula assumes span/depth > ~5 and small curvature. Brackets, deep web frames with large openings and slew-ring supports require shell/FE analysis (Section 7.11).

Elastic vs plastic section modulus

Rules use the elastic WWW. The plastic modulus WplW_{pl}Wpl​ (fully yielded section) is 1.1–1.5 times larger for stiffened plates; it is relevant to ultimate strength and accidental loads (collision, grounding), not to the normal rule check.

Formulas

01Flexure formula
σ(z)=M zI\sigma(z) = \frac{M\,z}{I}σ(z)=IMz​
SymbolDescriptionUnit
σ(z)\sigma(z)σ(z)Normal bending stress at distance z from the neutral axisMPa
MMMBending momentN·mm
zzzDistance from the neutral axis (positive away from the compression side as per sign convention)mm
IIISecond moment of area about the neutral axismm⁴

Result unit MPa

With M in kN·m, I in cm⁴ and z in cm: σ [MPa] = 100 M z / I.

02Maximum bending stress and section modulus
σmax⁡=MW,W=Izmax⁡\sigma_{\max} = \frac{M}{W}, \qquad W = \frac{I}{z_{\max}}σmax​=WM​,W=zmax​I​
SymbolDescriptionUnit
WWWElastic section modulus to the extreme fibre consideredmm³ (rules: cm³)
zmaxz_{max}zmax​Distance from the neutral axis to the extreme fibremm

Result unit MPa

σ [MPa] = 1000 M [kN·m] / W [cm³].

03Section moduli of simple shapes
Wrect=bh26,Wcircle=πd332,Wtube=π(do4−di4)32 doW_{\text{rect}} = \frac{b h^2}{6}, \qquad W_{\text{circle}} = \frac{\pi d^3}{32}, \qquad W_{\text{tube}} = \frac{\pi (d_o^4 - d_i^4)}{32\, d_o}Wrect​=6bh2​,Wcircle​=32πd3​,Wtube​=32do​π(do4​−di4​)​

Result unit mm³

04Shear stress in a beam (Jourawski)
τ(z)=V Q(z)I b(z)\tau(z) = \frac{V\,Q(z)}{I\,b(z)}τ(z)=Ib(z)VQ(z)​
SymbolDescriptionUnit
Q(z)Q(z)Q(z)First moment about the neutral axis of the area beyond zmm³
b(z)b(z)b(z)Width of the section at zmm

Result unit MPa

05Web shear approximation (rule shear area)
τ≈VAw=Vhw tw\tau \approx \frac{V}{A_w} = \frac{V}{h_w\,t_w}τ≈Aw​V​=hw​tw​V​
SymbolDescriptionUnit
hwh_whw​Web heightmm
twt_wtw​Web thicknessmm

Result unit MPa

Rules state a required shear area A_w in cm².

06Maximum shear stress factors
τmax⁡=32VA (rectangle),43VA (solid circle),2VA (thin tube)\tau_{\max} = \frac{3}{2}\frac{V}{A}\ (\text{rectangle}), \quad \frac{4}{3}\frac{V}{A}\ (\text{solid circle}), \quad 2\frac{V}{A}\ (\text{thin tube})τmax​=23​AV​ (rectangle),34​AV​ (solid circle),2AV​ (thin tube)

Result unit MPa

07Transformed section for two materials
n=E1E2,It=I2+n I1∗,σ1=n MzIt,σ2=MzItn = \frac{E_1}{E_2}, \qquad I_t = I_2 + n\,I_1^{*}, \qquad \sigma_1 = n\,\frac{M z}{I_t}, \quad \sigma_2 = \frac{M z}{I_t}n=E2​E1​​,It​=I2​+nI1∗​,σ1​=nIt​Mz​,σ2​=It​Mz​
SymbolDescriptionUnit
nnnModular ratio-
I1∗I_1^{*}I1∗​Second moment of the material-1 area (untransformed) about the common neutral axismm⁴

Result unit MPa

Steel/aluminium: n = 206/70 = 2.94.

Tables

Section properties of common rolled profiles used as stiffeners (profile alone, about own centroidal axis parallel to the plate)

ProfileArea [cm²]III [cm⁴]WWW to flange tip [cm³]Mass [kg/m]
Flat bar 100 × 1010.083.316.77.85
Flat bar 150 × 1218.0337.545.014.1
Flat bar 200 × 1530.0100010023.6
Bulb flat HP 120 × 710.414221.88.2
Bulb flat HP 160 × 815.737241.812.3
Bulb flat HP 200 × 1024.491582.519.2
Bulb flat HP 240 × 1132.6177013325.6
Angle L 100 × 75 × 813.5135 (about axis ∥ to 75 leg)19.510.6
T 200 × 10 + 80 × 12 (built-up)29.61397 (about own NA, 134.4 mm from web foot)—23.2
Source: Flat bars and T: computed; HP bulb flats: approximate values from manufacturer tables (e.g. Trinec/ArcelorMittal Holland Profiles) — verify against the supplier catalogue for the actual profile; angle: EN 10056-1.

The stiffener's own properties are only intermediate values; the design property is the modulus of the stiffener WITH its attached plate (Section 2.5).

Examples

#01

Bending and shear stress in the deck stiffener

Worked example

Problem

Using the moments of Example 2.3 (fixed ends: 7.20 kN·m at the support; simply supported: 10.80 kN·m) and the section properties of the T-stiffener with attached plate from Example 2.5 (INA=5252I_{NA} = 5252INA​=5252 cm⁴, Wflange=307W_{\text{flange}} = 307Wflange​=307 cm³, Wplate=1029W_{\text{plate}} = 1029Wplate​=1029 cm³, web 200 × 10 mm), compute the bending stresses at the flange and at the plate and the web shear stress for V = 18.0 kN.

Solution

Fixed-ended (rule assumption), at the support:

σflange=1000×7.20307=23.5 MPa,σplate=1000×7.201029=7.0 MPa\sigma_{\text{flange}} = \frac{1000 \times 7.20}{307} = 23.5\ \text{MPa}, \qquad \sigma_{\text{plate}} = \frac{1000 \times 7.20}{1029} = 7.0\ \text{MPa}σflange​=3071000×7.20​=23.5 MPa,σplate​=10291000×7.20​=7.0 MPa

Simply supported, at midspan: σflange=1000×10.80/307=35.2\sigma_{\text{flange}} = 1000 \times 10.80/307 = 35.2σflange​=1000×10.80/307=35.2 MPa; σplate=10.5\sigma_{\text{plate}} = 10.5σplate​=10.5 MPa.

Web shear: Aw=200×10=2000A_w = 200 \times 10 = 2000Aw​=200×10=2000 mm² = 20 cm²; τ=18 000/2000=9.0\tau = 18\,000/2000 = 9.0τ=18000/2000=9.0 MPa.

All values are far below the allowable for local bending in a deck (of the order of 0.6–0.8 σ_y ≈ 140–190 MPa for mild steel, see Section 2.12), as expected for a 25 kPa deck load on a 200 mm stiffener; the stiffener size on a PSV deck is usually governed by heavier point loads (containers, deck cargo lashings) or by the hull-girder contribution, not by the uniform pressure. The flange modulus (307 cm³) governs because it is the smaller — confirm this against the rule-required Z in Section 7.6.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 5 (Stresses in beams: flexure formula, shear stresses, composite beams)Textbook
Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)Clause Ch. 9 (Stiffened panels — beam theory for stiffeners)Textbook
DNV Rules for Classification — Ships, Pt.3 Ch.6 (Hull local scantling)Clause Sec. 5 (Stiffeners — section modulus and shear area requirements)Mandatory

Rule form Z = C s ℓ² p / σ in cm³; confirm section numbers in the edition in force.

Previous · 2.3Shear force and bending moment diagramsNext · 2.5Section properties of built-up sections (stiffener + plate)

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Flexure formula
  • Units in rule formulas
  • Shear stress in beams
  • Composite (two-material) beams
  • Curved and deep beams
  • Elastic vs plastic section modulus
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 5 (Stresses in beams: flexure formula, shear stresses, composite beams)

  • Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)

    Ch. 9 (Stiffened panels — beam theory for stiffeners)

  • DNV Rules for Classification — Ships, Pt.3 Ch.6 (Hull local scantling)

    Sec. 5 (Stiffeners — section modulus and shear area requirements)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.