NavArchHandbook0 ch

No chapters yet.

Engineering toolsIndex of symbolsGlossaryReferences
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›2. Mechanics & Strength of Materials›2.3 Shear force and bending moment diagrams

Chapter 2 / Section 2.3

Shear force and bending moment diagrams

Print this section

Definitions and sign convention

For a beam along xxx with distributed load q(x)q(x)q(x) (positive downward), shear force V(x)V(x)V(x) and bending moment M(x)M(x)M(x):

dVdx=−q,dMdx=V\frac{dV}{dx} = -q, \qquad \frac{dM}{dx} = VdxdV​=−q,dxdM​=V

Sign convention (Gere/Hibbeler): positive MMM produces compression in the top fibre ("sagging"); positive VVV acts downward on the right-hand face of a cut. In ship longitudinal strength the opposite naming is used for the hull girder: hogging (deck in tension, keel in compression) is usually taken positive in class rules — always state the convention.

Procedure

  1. Free-body diagram; compute support reactions from ∑F=0\sum F = 0∑F=0, ∑M=0\sum M = 0∑M=0.
  2. Cut the beam at xxx; V(x)V(x)V(x) = sum of forces to the left; M(x)M(x)M(x) = sum of moments of those forces about the cut.
  3. Between loads VVV is constant under no load, linear under UDL; MMM is linear under no load, parabolic under UDL. A point load gives a jump in VVV; a point moment gives a jump in MMM.
  4. MMM is extreme where V=0V = 0V=0 (or changes sign). The area under the VVV diagram between two sections equals the change of MMM.

The ship as a beam

The hull girder is a free–free beam: the load is the difference between the weight distribution w(x)w(x)w(x) and the buoyancy distribution b(x)b(x)b(x) (from Bonjean areas, Section 4.10):

V(x)=∫0x(b−w) dx,M(x)=∫0xV dxV(x) = \int_0^x \big(b - w\big)\,dx, \qquad M(x) = \int_0^x V\,dxV(x)=∫0x​(b−w)dx,M(x)=∫0x​Vdx

Both integrals must return to zero at the far end (equilibrium: Δ=ρ∇\Delta = \rho\nablaΔ=ρ∇ and LCG=LCBLCG = LCBLCG=LCB); a non-zero closing error indicates an inconsistency in the weight or buoyancy curves. The still-water bending moment (SWBM) is the result; the wave bending moment is added from rule formulas (Section 7.2).

Stiffeners and girders as beams

Rule scantling formulas assume a stiffener continuous over several supports (frames) under uniform pressure: the design moment at the support is q ℓ2/12q\,\ell^2/12qℓ2/12 (fixed-ended), the field moment q ℓ2/24q\,\ell^2/24qℓ2/24. Simply supported assumptions (q ℓ2/8q\,\ell^2/8qℓ2/8) apply to stiffeners with sniped ends. Class rules reflect this by the end-fixity coefficient in the section modulus formula (Section 7.6).

Standard cases

The table gives reactions, maximum shear, maximum moment and maximum deflection for the beam cases used daily. qqq = load per unit length, PPP = point load, LLL = span, EIEIEI = flexural rigidity.

Formulas

01Differential relations of beam theory
dVdx=−q(x),dMdx=V(x),d2Mdx2=−q(x)\frac{dV}{dx} = -q(x), \qquad \frac{dM}{dx} = V(x), \qquad \frac{d^2M}{dx^2} = -q(x)dxdV​=−q(x),dxdM​=V(x),dx2d2M​=−q(x)
SymbolDescriptionUnit
q(x)q(x)q(x)Distributed load, positive downwardkN/m
V(x)V(x)V(x)Shear forcekN
M(x)M(x)M(x)Bending momentkN·m

Result unit -

02Hull girder shear force and bending moment
V(x)=∫0x(b(ξ)−w(ξ)) dξ,M(x)=∫0xV(ξ) dξV(x) = \int_0^x \big(b(\xi) - w(\xi)\big)\,d\xi, \qquad M(x) = \int_0^x V(\xi)\,d\xiV(x)=∫0x​(b(ξ)−w(ξ))dξ,M(x)=∫0x​V(ξ)dξ
SymbolDescriptionUnit
b(x)b(x)b(x)Buoyancy per unit length (ρ g A(x))kN/m
w(x)w(x)w(x)Weight per unit lengthkN/m

Result unit kN, kN·m

Both must be zero at x = L (equilibrium closure).

03Fixed-ended beam under UDL (continuous stiffener)
Msupport=−q ℓ212,Mmid=+q ℓ224,Vmax⁡=q ℓ2M_{\text{support}} = -\frac{q\,\ell^2}{12}, \qquad M_{\text{mid}} = +\frac{q\,\ell^2}{24}, \qquad V_{\max} = \frac{q\,\ell}{2}Msupport​=−12qℓ2​,Mmid​=+24qℓ2​,Vmax​=2qℓ​
SymbolDescriptionUnit
ℓ\ellℓSpan between supportsm

Result unit kN·m

04Simply supported beam under UDL
Mmax⁡=q ℓ28,Vmax⁡=q ℓ2M_{\max} = \frac{q\,\ell^2}{8}, \qquad V_{\max} = \frac{q\,\ell}{2}Mmax​=8qℓ2​,Vmax​=2qℓ​

Result unit kN·m

05Line load on a stiffener from a pressure
q=p sq = p\,sq=ps
SymbolDescriptionUnit
pppDesign pressurekPa = kN/m²
sssStiffener spacingm

Result unit kN/m

Tables

Standard beam cases — reactions, maximum shear, maximum moment, maximum deflection

CaseReactionsVmax⁡V_{\max}Vmax​Mmax⁡M_{\max}Mmax​ (location)δmax⁡\delta_{\max}δmax​ (location)
Simply supported, point load P at midspanP/2P/2P/2 eachP/2P/2P/2PL/4PL/4PL/4 (midspan)PL3/(48EI)PL^3/(48EI)PL3/(48EI) (midspan)
Simply supported, point load P at distance a from left (b = L − a)Pb/LPb/LPb/L, Pa/LPa/LPa/Lmax⁡(Pa/L,Pb/L)\max(Pa/L, Pb/L)max(Pa/L,Pb/L)Pab/LPab/LPab/L (under load)Pab(a+2b)3a(a+2b)27 EI L\dfrac{Pab(a+2b)\sqrt{3a(a+2b)}}{27\,EI\,L}27EILPab(a+2b)3a(a+2b)​​ at x=a(a+2b)/3x=\sqrt{a(a+2b)/3}x=a(a+2b)/3​ from left, for a ≥ b
Simply supported, UDL qqL/2qL/2qL/2 eachqL/2qL/2qL/2qL2/8qL^2/8qL2/8 (midspan)5qL4/(384EI)5qL^4/(384EI)5qL4/(384EI) (midspan)
Cantilever, point load P at free endPPP; M=PLM = PLM=PLPPPPLPLPL (fixed end)PL3/(3EI)PL^3/(3EI)PL3/(3EI) (free end)
Cantilever, UDL qqLqLqL; M=qL2/2M = qL^2/2M=qL2/2qLqLqLqL2/2qL^2/2qL2/2 (fixed end)qL4/(8EI)qL^4/(8EI)qL4/(8EI) (free end)
Fixed both ends, point load P at midspanP/2P/2P/2 eachP/2P/2P/2PL/8PL/8PL/8 (ends and midspan)PL3/(192EI)PL^3/(192EI)PL3/(192EI) (midspan)
Fixed both ends, UDL qqL/2qL/2qL/2 eachqL/2qL/2qL/2qL2/12qL^2/12qL2/12 (ends); qL2/24qL^2/24qL2/24 (midspan)qL4/(384EI)qL^4/(384EI)qL4/(384EI) (midspan)
Propped cantilever (fixed–pinned), UDL q5qL/85qL/85qL/8 (fixed), 3qL/83qL/83qL/8 (pinned)5qL/85qL/85qL/8qL2/8qL^2/8qL2/8 (fixed end); 9qL2/1289qL^2/1289qL2/128 at 3L/83L/83L/8 from pinned endqL4/(185EI)qL^4/(185EI)qL4/(185EI) at 0.4215L0.4215L0.4215L from fixed end
Simply supported, end moment M_0 at one endM0/LM_0/LM0​/L each (opposite)M0/LM_0/LM0​/LM0M_0M0​ (loaded end)M0L2/(93 EI)M_0L^2/(9\sqrt3\,EI)M0​L2/(93​EI) at L/3L/\sqrt3L/3​ from the free end
Simply supported with overhang / continuous beams——Use superposition or moment distribution; three-moment equation—
Source: Gere & Timoshenko (1999) Appendix G; Roark's Formulas, 8th ed. (2012) Table 8.1; Hibbeler (2017) Appendix C.

Examples

#01

Shear and moment in a deck stiffener

Worked example

Problem

A deck longitudinal of the example vessel spans ℓ=2.40\ell = 2.40ℓ=2.40 m between transverse web frames, spacing s=0.60s = 0.60s=0.60 m, design deck pressure p=25p = 25p=25 kPa (deck cargo). Determine the line load, the maximum shear force and the bending moments for (a) the continuous (fixed-ended) stiffener assumed by the rules and (b) a simply supported stiffener with sniped ends.

Solution

Line load: q=p s=25×0.60=15.0q = p\,s = 25 \times 0.60 = 15.0q=ps=25×0.60=15.0 kN/m.

Shear (both cases): Vmax⁡=qℓ/2=15.0×2.40/2=18.0V_{\max} = q\ell/2 = 15.0 \times 2.40/2 = 18.0Vmax​=qℓ/2=15.0×2.40/2=18.0 kN.

(a) Fixed ends: Msupport=qℓ2/12=15.0×5.76/12=7.20M_{\text{support}} = q\ell^2/12 = 15.0 \times 5.76/12 = 7.20Msupport​=qℓ2/12=15.0×5.76/12=7.20 kN·m; Mmid=3.60M_{\text{mid}} = 3.60Mmid​=3.60 kN·m.

(b) Simply supported: Mmax⁡=qℓ2/8=10.80M_{\max} = q\ell^2/8 = 10.80Mmax​=qℓ2/8=10.80 kN·m.

The sniped-end stiffener carries 50 % more moment at midspan and has no support moment; the rules penalise sniped ends with a lower end-fixity coefficient (equivalently a higher required section modulus). These moments are used in Example 2.4 for the stress check and in 2.6 for deflection.

#02

Closure check of a hull girder load curve

Worked example

Problem

For a 60 m barge, the integrated weight is 1635 t and the integrated buoyancy from Bonjean areas is 1595 m³ × 1.025 = 1635 t; the LCG is 0.81 m aft of midship and the LCB (Example 4.10) 0.81 m aft. The shear force curve computed from AP closes at the FP with V = +12 kN and the moment with M = +180 kN·m. Is the calculation acceptable?

Solution

Total load =1635×9.81=16 039= 1635 \times 9.81 = 16\,039=1635×9.81=16039 kN. The shear closing error is 12/16 039=0.07 %12/16\,039 = 0.07\ \%12/16039=0.07 % and the moment closing error is small relative to the maximum SWBM (of the order of 0.01×ΔgL≈96000.01 \times \Delta g L \approx 96000.01×ΔgL≈9600 kN·m for a barge): 180/9600=1.9 %180/9600 = 1.9\ \%180/9600=1.9 %. Both are within the usual tolerance of station-wise integration (shear < 0.5 %, moment < 2–3 % of the maximum); class software distributes the closing error linearly along the length. If the moment error exceeded ~5 %, re-check the weight distribution (an item at the wrong station) or the Bonjean readings at the ends.

References

Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)Clause Ch. 4 (Shear forces and bending moments)Textbook
Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)Clause Ch. 3 (Hull girder response — load, shear and moment curves)Textbook
Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)Clause Vol. 1, Ch. 6 (The ship girder — weight, buoyancy, loading, shearing force and bending moment curves)Textbook
Previous · 2.2Axial loading, thermal stress and simple connectionsNext · 2.4Bending stress and section modulus of beams

Version 2 · last updated 19 Nov 2026 · Editor

On this page

  • Definitions and sign convention
  • Procedure
  • The ship as a beam
  • Stiffeners and girders as beams
  • Standard cases
  • Formulas
  • Tables
  • Examples
  • References

Applicable standards

  • Gere & Timoshenko, Mechanics of Materials, 4th SI ed. (1999)

    Ch. 4 (Shear forces and bending moments)

  • Hughes & Paik, Ship Structural Analysis and Design (SNAME, 2010)

    Ch. 3 (Hull girder response — load, shear and moment curves)

  • Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)

    Vol. 1, Ch. 6 (The ship girder — weight, buoyancy, loading, shearing force and bending moment curves)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.