NavArch Handbook
Chapter 2 / Section 2.3
For a beam along with distributed load (positive downward), shear force and bending moment :
Sign convention (Gere/Hibbeler): positive produces compression in the top fibre ("sagging"); positive acts downward on the right-hand face of a cut. In ship longitudinal strength the opposite naming is used for the hull girder: hogging (deck in tension, keel in compression) is usually taken positive in class rules — always state the convention.
The hull girder is a free–free beam: the load is the difference between the weight distribution and the buoyancy distribution (from Bonjean areas, Section 4.10):
Both integrals must return to zero at the far end (equilibrium: and ); a non-zero closing error indicates an inconsistency in the weight or buoyancy curves. The still-water bending moment (SWBM) is the result; the wave bending moment is added from rule formulas (Section 7.2).
Rule scantling formulas assume a stiffener continuous over several supports (frames) under uniform pressure: the design moment at the support is (fixed-ended), the field moment . Simply supported assumptions () apply to stiffeners with sniped ends. Class rules reflect this by the end-fixity coefficient in the section modulus formula (Section 7.6).
The table gives reactions, maximum shear, maximum moment and maximum deflection for the beam cases used daily. = load per unit length, = point load, = span, = flexural rigidity.
| Symbol | Description | Unit |
|---|---|---|
| Distributed load, positive downward | kN/m | |
| Shear force | kN | |
| Bending moment | kN·m |
Result unit -
| Symbol | Description | Unit |
|---|---|---|
| Buoyancy per unit length (ρ g A(x)) | kN/m | |
| Weight per unit length | kN/m |
Result unit kN, kN·m
Both must be zero at x = L (equilibrium closure).
| Symbol | Description | Unit |
|---|---|---|
| Span between supports | m |
Result unit kN·m
Result unit kN·m
| Symbol | Description | Unit |
|---|---|---|
| Design pressure | kPa = kN/m² | |
| Stiffener spacing | m |
Result unit kN/m
| Case | Reactions | (location) | (location) | |
|---|---|---|---|---|
| Simply supported, point load P at midspan | each | (midspan) | (midspan) | |
| Simply supported, point load P at distance a from left (b = L − a) | , | (under load) | at from left, for a ≥ b | |
| Simply supported, UDL q | each | (midspan) | (midspan) | |
| Cantilever, point load P at free end | ; | (fixed end) | (free end) | |
| Cantilever, UDL q | ; | (fixed end) | (free end) | |
| Fixed both ends, point load P at midspan | each | (ends and midspan) | (midspan) | |
| Fixed both ends, UDL q | each | (ends); (midspan) | (midspan) | |
| Propped cantilever (fixed–pinned), UDL q | (fixed), (pinned) | (fixed end); at from pinned end | at from fixed end | |
| Simply supported, end moment M_0 at one end | each (opposite) | (loaded end) | at from the free end | |
| Simply supported with overhang / continuous beams | — | — | Use superposition or moment distribution; three-moment equation | — |
Worked example
Problem
A deck longitudinal of the example vessel spans m between transverse web frames, spacing m, design deck pressure kPa (deck cargo). Determine the line load, the maximum shear force and the bending moments for (a) the continuous (fixed-ended) stiffener assumed by the rules and (b) a simply supported stiffener with sniped ends.
Solution
Line load: kN/m.
Shear (both cases): kN.
(a) Fixed ends: kN·m; kN·m.
(b) Simply supported: kN·m.
The sniped-end stiffener carries 50 % more moment at midspan and has no support moment; the rules penalise sniped ends with a lower end-fixity coefficient (equivalently a higher required section modulus). These moments are used in Example 2.4 for the stress check and in 2.6 for deflection.
Worked example
Problem
For a 60 m barge, the integrated weight is 1635 t and the integrated buoyancy from Bonjean areas is 1595 m³ × 1.025 = 1635 t; the LCG is 0.81 m aft of midship and the LCB (Example 4.10) 0.81 m aft. The shear force curve computed from AP closes at the FP with V = +12 kN and the moment with M = +180 kN·m. Is the calculation acceptable?
Solution
Total load kN. The shear closing error is and the moment closing error is small relative to the maximum SWBM (of the order of kN·m for a barge): . Both are within the usual tolerance of station-wise integration (shear < 0.5 %, moment < 2–3 % of the maximum); class software distributes the closing error linearly along the length. If the moment error exceeded ~5 %, re-check the weight distribution (an item at the wrong station) or the Bonjean readings at the ends.