Chapter 5 / Section 5.4
Stability at large angles: GZ curves, cross curves (KN)
Why the metacentre is not enough
Beyond about 10° the metacentre moves and no longer holds; deck-edge immersion, bilge emergence, superstructure and watertight deckhouses change the shape of the immersed volume. Stability at large angles is described by the curve of statical stability — against heel angle — for each loading condition.
Cross curves of stability (KN curves)
For a given hull, the righting lever depends on displacement and on . To separate the hull geometry from the loading, the designer computes, for a series of displacements and heel angles, the lever : the horizontal distance from the keel point to the vertical through the heeled centre of buoyancy. Then for any :
values are tabulated or plotted against displacement for = 10°, 20°, …, 90° (sometimes 5°, 12°, 15°, 60°, 75° are added). Older booklets give curves for an assumed pole at height : .
Free trim vs fixed trim
Cross curves must be computed with the ship free to trim at each heel angle (the ship trims as she heels, especially with large aft superstructures or trawl decks). Fixed-trim KN values can overstate GZ by several centimetres.
Features of the GZ curve
- Initial slope — at the origin the slope equals : the tangent at reaches the value at rad (57.3°). This is the standard construction check.
- Deck-edge immersion — a point of inflexion; beyond it the curve flattens.
- Maximum and its angle .
- Range of stability — the angle at which returns to zero (angle of vanishing stability). Practically the range is cut at the downflooding angle at which the first non-weathertight opening immerses.
- Watertight superstructures and deckhouses (per IS Code Part B Ch. 3.1) may be included in the buoyant volume and increase and the range.
Effect of KG and of a transverse shift of G
- A higher reduces everywhere by (the " curve").
- A transverse offset reduces by and produces a static list where the curves intersect.
Heeling moment curves
External heeling moments (wind, towline, crane, crowding, turning) are plotted as heeling levers on the same diagram. The static heel is where ; the residual area between the curves is used in the dynamic criteria (Section 5.5, 5.7).
Formulas
| Symbol | Description | Unit |
|---|---|---|
| Cross-curve lever (keel to vertical through heeled B) | m | |
| Height of centre of gravity (fluid, i.e. including free surface correction) | m |
Result unit m
| Symbol | Description | Unit |
|---|---|---|
| Transverse offset of G from centreline towards the heeled side | m |
Result unit m
Result unit m/rad
| Symbol | Description | Unit |
|---|---|---|
| Heeling lever | m | |
| Heeling moment | kN·m | |
| Displacement | t |
Result unit m
If M_h is in t·m, omit g.
| Symbol | Description | Unit |
|---|---|---|
| Service speed | m/s | |
| Waterline length | m | |
| Mean draught | m |
Result unit m
Passenger ships (IS Code Part B 3.1.2) — heel not to exceed 10°.
Tables
Cross curves (KN) of the example vessel at Δ = 6314 t (free to trim) — illustrative
| Heel [°] | [m] | |
|---|---|---|
| 10 | 0.1736 | 1.045 |
| 20 | 0.3420 | 2.110 |
| 30 | 0.5000 | 3.125 |
| 40 | 0.6428 | 3.930 |
| 50 | 0.7660 | 4.490 |
| 60 | 0.8660 | 4.840 |
| 70 | 0.9397 | 5.000 |
Examples
GZ curve of the example vessel from KN values
Worked example
Problem
Using the KN table above and a fluid m (solid 5.21 m plus free surface correction 0.07 m), compute the GZ curve, the maximum GZ and its angle, and estimate the range of stability.
References
Version 2 · last updated 19 Nov 2026 · Editor