NavArchHandbook0 ch

No chapters yet.

Engineering tools
NavArchHandbook
NavArchHandbook
↵
BookmarksTools
Home›4. Ship Geometry & Hydrostatics›4.1 Principal dimensions and definitions

Chapter 4 / Section 4.1

Principal dimensions and definitions

Print this section

Length

  • Length overall, LOAL_{OA}LOA​ — extreme length between the foremost and aftermost points of the hull, excluding removable fittings. Used for berthing, docking and some small-craft rules.
  • Length between perpendiculars, LBPL_{BP}LBP​ (or LPPL_{PP}LPP​) — distance between the forward perpendicular (FP, intersection of the design waterline with the stem) and the aft perpendicular (AP, usually the centreline of the rudder stock). Used in most hydrostatic and structural rule formulas.
  • Length on the waterline, LWLL_{WL}LWL​ — length of the hull at the design waterline. Used for resistance (Froude number) and for the waterplane coefficient.
  • Load Line length, LLL (ICLL) — per the International Convention on Load Lines 1966/1988, Annex I Reg. 3(1): the greater of (a) 96 % of the total length on a waterline at 85 % of the least moulded depth measured from the top of the keel, and (b) the length from the fore side of the stem to the axis of the rudder stock on that waterline. Used for freeboard assignment and for SOLAS/MARPOL applicability thresholds.
  • Rule length, LLL (classification) — defined by each classification society for its structural formulas; in DNV Rules Pt.3 Ch.1 Sec.4 it is the distance on the summer load waterline from the fore side of the stem to the axis of the rudder stock, but not less than 96 % and need not be greater than 97 % of the extreme length on that waterline. Always confirm the definition in the rule set in force before applying a scantling formula.

Breadth, depth, draught

  • Moulded breadth, BBB — greatest breadth measured to the inside of shell plating (moulded line) amidships.
  • Extreme breadth — includes shell plating, fenders, rubbing strakes.
  • Moulded depth, DDD — vertical distance at the side, amidships, from the top of the keel (baseline) to the top of the freeboard deck beam.
  • Draught, TTT — vertical distance from the baseline to the waterline. TAT_ATA​ (aft), TFT_FTF​ (forward), TMT_MTM​ (mean, at midship). Trim =TA−TF= T_A - T_F=TA​−TF​ (positive by the stern in most European practice; always state the convention).
  • Freeboard, fff — vertical distance from the waterline to the freeboard deck at side: f=D−Tf = D - Tf=D−T (moulded, before corrections for deck thickness, sheer, camber and superstructures per ICLL).
  • Air draught — height from waterline to the highest fixed point.

Reference planes and midship

  • Baseline (BL) — horizontal line through the top of the keel plate at midship (moulded).
  • Centreline plane (CL) — vertical longitudinal plane of symmetry.
  • Midship section (⊗) — transverse section at LBP/2L_{BP}/2LBP​/2.
  • Station spacing — LBPL_{BP}LBP​ is usually divided into 10 or 20 equal intervals (stations 0 at AP to 10 or 20 at FP) for hydrostatic integration.

Hull form terms

  • Sheer — longitudinal curvature of the deck at side.
  • Camber (round of beam) — transverse curvature of the deck; standard camber B/50B/50B/50.
  • Rise of floor (deadrise) — rise of the bottom from the keel to the turn of bilge; in small craft given as deadrise angle β\betaβ.
  • Tumblehome / flare — inward / outward inclination of the side above the waterline.
  • Parallel middle body — length over which the midship section is constant.
  • Entrance / run — forward / aft portion of the hull where the sections change.

Displacement terms

  • Volume of displacement, ∇\nabla∇ [m³] — moulded volume of the immersed hull. Add shell plating and appendages for extreme displacement.
  • Mass displacement, Δ\DeltaΔ [t] — Δ=ρ∇\Delta = \rho \nablaΔ=ρ∇.
  • Lightship — complete vessel without cargo, fuel, stores, crew, water, ballast.
  • Deadweight, DWTDWTDWT — Δloaded−Δlightship\Delta_{\text{loaded}} - \Delta_{\text{lightship}}Δloaded​−Δlightship​.
  • Load line marks — summer, winter, tropical, fresh water marks per ICLL 1966/1988.

Formulas

01Mass displacement
Δ=ρ ∇\Delta = \rho \, \nablaΔ=ρ∇
SymbolDescriptionUnit
Δ\DeltaΔMass displacementt
ρ\rhoρWater density (seawater 1.025)t/m^3
∇\nabla∇Volume of displacementm^3

Result unit t

Use moulded volume plus shell and appendage allowance (typically +0.5 % to +1 % of moulded volume for steel ships) for the extreme displacement.

02Deadweight
DWT=Δloaded−ΔlightDWT = \Delta_{\text{loaded}} - \Delta_{\text{light}}DWT=Δloaded​−Δlight​
SymbolDescriptionUnit
DWTDWTDWTDeadweightt
Δloaded\Delta_{\text{loaded}}Δloaded​Displacement at the load draughtt
Δlight\Delta_{\text{light}}Δlight​Lightship displacementt

Result unit t

03Moulded freeboard
f=D−Tf = D - Tf=D−T
SymbolDescriptionUnit
fffMoulded freeboard at side amidshipsm
DDDMoulded depthm
TTTDraughtm

Result unit m

The statutory (assigned) freeboard is determined per ICLL 1966/1988 and includes corrections; this is the geometric freeboard only.

04Trim
t=TA−TFt = T_A - T_Ft=TA​−TF​
SymbolDescriptionUnit
tttTrim (positive by the stern with this sign convention)m
TAT_ATA​Draught at aft perpendicularm
TFT_FTF​Draught at forward perpendicularm

Result unit m

Tables

Typical ratios of principal dimensions

Ship typeL/BB/TD/T (approx.)Notes
Offshore supply / PSV (60–95 m)3.5–4.52.5–3.51.2–1.5Full form, high B/T for deck load and stability
General cargo / multipurpose5.5–7.02.3–2.81.3–1.5—
Container ship6.0–8.02.5–3.51.5–2.0High D for container stacks
Tanker / bulk carrier5.0–6.52.4–3.01.2–1.4—
Fishing vessel (15–60 m)3.0–4.52.2–3.01.1–1.5Stern trawlers fuller than purse seiners
Fast ferry / patrol (planing/semi-planing)4.5–7.03.0–5.0——
Tug2.5–3.52.0–2.81.3–1.6—
Source: Indicative ranges compiled from Schneekluth & Bertram (1998) Ch. 1 and Watson, Practical Ship Design (1998) Ch. 3. Use only for first estimates.

References

International Convention on Load Lines, 1966, as modified by the 1988 ProtocolClause Annex I, Reg. 3 (Definitions of terms)Mandatory

Statutory definitions of length, breadth, depth and freeboard used for load line assignment.

DNV Rules for Classification — Ships, Pt.3 Ch.1 (General principles)Clause Sec. 4 (Symbols and definitions)Mandatory

Rule length L, breadth B, depth D and scantling draught as used in all DNV structural formulas. Check the current edition in force.

Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)Clause Vol. 1, Ch. 2 (Some tools)Textbook

Standard definitions and notation.

Previous · 3.10Material certificates, traceability and class requirementsNext · 4.2Lines plan, body plan and offsets

Version 3 · last updated 19 Nov 2026 · Editor

On this page

  • Length
  • Breadth, depth, draught
  • Reference planes and midship
  • Hull form terms
  • Displacement terms
  • Formulas
  • Tables
  • References

Applicable standards

  • International Convention on Load Lines, 1966, as modified by the 1988 Protocol

    Annex I, Reg. 3 (Definitions of terms)

  • DNV Rules for Classification — Ships, Pt.3 Ch.1 (General principles)

    Sec. 4 (Symbols and definitions)

  • Rawson & Tupper, Basic Ship Theory, 5th ed. (2001)

    Vol. 1, Ch. 2 (Some tools)

NavArch Handbook·About & disclaimerFeedbackBookmarks© Jadrija Maritime j.d.o.o.