Chapter 5 / Section 5.7
IMO 2008 IS Code: severe wind and rolling (weather) criterion
Scope
Part A, Ch. 2.3 of the IS Code. Applies to passenger and cargo ships of 24 m and above (and, through Part B, to fishing vessels of 45 m and above — Part B Ch. 2.1.4). It demonstrates the ability of the ship to withstand the combined effect of beam wind and rolling.
Scenario
- The ship is subjected to a steady wind pressure acting perpendicular to the centreline, giving a steady wind heeling lever .
- From the resulting static angle the ship is assumed to roll to windward by an angle due to wave action.
- A gust then acts, with heeling lever .
- Under this gust, the energy balance requires that the area b (between and the GZ curve from to ) be ≥ the area a (between the GZ curve and from to ).
Where = min(angle of second intersection of with GZ curve, downflooding angle , 50°).
Additional requirement
The static heel under the steady wind, , shall not exceed 16° or 80 % of the angle of deck-edge immersion, whichever is less.
Steady wind heeling lever
- = 504 Pa (wind pressure; Administrations may reduce for restricted service);
- = projected lateral area of the ship and deck cargo above the waterline [m²];
- = vertical distance from the centroid of to the centre of the underwater lateral area (or approximately to a point at half the draught) [m];
- in t; = 9.81.
Roll-back angle
- = factor from Table 2.3.4-1 as a function of ;
- = factor from Table 2.3.4-2 as a function of ;
- = 1.0 for round-bilge ship without bilge keels or bar keel; 0.7 for sharp bilge; from Table 2.3.4-3 as a function of for ships with bilge keels/bar keel ( = total area of bilge keels, or area of lateral projection of bar keel, or sum);
- with = distance of G above the waterline (positive up);
- = factor from Table 2.3.4-4 as a function of the roll period , with .
Note that the Code places no upper cap on ; the 16° limit applies to the static angle only. For ships fitted with anti-rolling devices, the devices are assumed inoperative.
The factor tables are reproduced below. Intermediate values are obtained by linear interpolation.
Formulas
| Symbol | Description | Unit |
|---|---|---|
| Steady wind heeling lever (constant with heel) | m | |
| Wind pressure (504 Pa unrestricted service) | Pa | |
| Projected lateral area above waterline (hull, superstructure, deck cargo) | m^2 | |
| Vertical lever: centroid of A to centre of underwater lateral area (≈ T/2) | m | |
| Displacement | t | |
| 9.81 | m/s^2 |
Result unit m
Result unit m
| Symbol | Description | Unit |
|---|---|---|
| Roll angle to windward from static heel | deg | |
| Bilge/keel factor (1.0 round bilge, 0.7 sharp bilge, table for bilge keels) | - | |
| Factor of B/d (Table 2.3.4-1) | - | |
| Factor of C_B (Table 2.3.4-2) | - | |
| 0.73 + 0.6 OG/d | - | |
| Factor of roll period T (Table 2.3.4-4) | - |
Result unit deg
| Symbol | Description | Unit |
|---|---|---|
| Roll period | s | |
| Mean moulded draught | m | |
| Fluid metacentric height | m |
Result unit s
| Symbol | Description | Unit |
|---|---|---|
| Static heel under steady wind l_w1 | deg | |
| min(second intersection, φf, 50°) | deg |
Result unit m·rad
GZ is negative for negative angles (windward side): GZ(−φ) = −GZ(φ) for a symmetric ship.
Result unit deg
Tables
Factor (IS Code Table 2.3.4-1)
| ≤ 2.4 | 1.00 |
| 2.5 | 0.98 |
| 2.6 | 0.96 |
| 2.7 | 0.95 |
| 2.8 | 0.93 |
| 2.9 | 0.91 |
| 3.0 | 0.90 |
| 3.1 | 0.88 |
| 3.2 | 0.86 |
| 3.4 | 0.82 |
| ≥ 3.5 | 0.80 |
Factor (IS Code Table 2.3.4-2)
| ≤ 0.45 | 0.75 |
| 0.50 | 0.82 |
| 0.55 | 0.89 |
| 0.60 | 0.95 |
| 0.65 | 0.97 |
| ≥ 0.70 | 1.00 |
Factor for bilge keels (IS Code Table 2.3.4-3)
| 0 | 1.00 |
| 1.0 | 0.98 |
| 1.5 | 0.95 |
| 2.0 | 0.88 |
| 2.5 | 0.79 |
| 3.0 | 0.74 |
| 3.5 | 0.72 |
| ≥ 4.0 | 0.70 |
Factor (IS Code Table 2.3.4-4)
| [s] | |
|---|---|
| ≤ 6 | 0.100 |
| 7 | 0.098 |
| 8 | 0.093 |
| 12 | 0.065 |
| 14 | 0.053 |
| 16 | 0.044 |
| 18 | 0.038 |
| ≥ 20 | 0.035 |
Examples
Weather criterion inputs for the example vessel
Worked example
Problem
Example vessel: t, m, m, m, , fluid m, m, projected lateral area above WL m² with centroid 7.2 m above WL, round bilge with bilge keels of total area m². Compute , , , and .
References
Model-test based alternative for ships with unusual parameters (e.g. B/d > 3.5, OG/d outside −0.3 to 0.5, T > 20 s).
Version 2 · last updated 19 Nov 2026 · Editor