Back to section

NavArch Handbook

Chapter 5 / Section 5.7

IMO 2008 IS Code: severe wind and rolling (weather) criterion

Scope

Part A, Ch. 2.3 of the IS Code. Applies to passenger and cargo ships of 24 m and above (and, through Part B, to fishing vessels of 45 m and above — Part B Ch. 2.1.4). It demonstrates the ability of the ship to withstand the combined effect of beam wind and rolling.

Scenario

  1. The ship is subjected to a steady wind pressure acting perpendicular to the centreline, giving a steady wind heeling lever lw1l_{w1}lw1​.
  2. From the resulting static angle φ0\varphi_0φ0​ the ship is assumed to roll to windward by an angle φ1\varphi_1φ1​ due to wave action.
  3. A gust then acts, with heeling lever lw2=1.5 lw1l_{w2} = 1.5\,l_{w1}lw2​=1.5lw1​.
  4. Under this gust, the energy balance requires that the area b (between lw2l_{w2}lw2​ and the GZ curve from φ0\varphi_0φ0​ to φ2\varphi_2φ2​) be ≥ the area a (between the GZ curve and lw2l_{w2}lw2​ from φ0−φ1\varphi_0 - \varphi_1φ0​−φ1​ to φ0\varphi_0φ0​).

Where φ2\varphi_2φ2​ = min(angle of second intersection of lw2l_{w2}lw2​ with GZ curve, downflooding angle φf\varphi_fφf​, 50°).

Additional requirement

The static heel under the steady wind, φ0\varphi_0φ0​, shall not exceed 16° or 80 % of the angle of deck-edge immersion, whichever is less.

Steady wind heeling lever

lw1=P A Z1000 g Δl_{w1} = \frac{P\,A\,Z}{1000\,g\,\Delta}lw1​=1000gΔPAZ​
  • PPP = 504 Pa (wind pressure; Administrations may reduce for restricted service);
  • AAA = projected lateral area of the ship and deck cargo above the waterline [m²];
  • ZZZ = vertical distance from the centroid of AAA to the centre of the underwater lateral area (or approximately to a point at half the draught) [m];
  • Δ\DeltaΔ in t; ggg = 9.81.

Roll-back angle

φ1=109 k X1 X2r s[deg]\varphi_1 = 109\,k\,X_1\,X_2\sqrt{r\,s} \quad [\text{deg}]φ1​=109kX1​X2​rs​[deg]
  • X1X_1X1​ = factor from Table 2.3.4-1 as a function of B/dB/dB/d;
  • X2X_2X2​ = factor from Table 2.3.4-2 as a function of CBC_BCB​;
  • kkk = 1.0 for round-bilge ship without bilge keels or bar keel; 0.7 for sharp bilge; from Table 2.3.4-3 as a function of 100Ak/(LB)100 A_k/(L B)100Ak​/(LB) for ships with bilge keels/bar keel (AkA_kAk​ = total area of bilge keels, or area of lateral projection of bar keel, or sum);
  • r=0.73+0.6 OG/dr = 0.73 + 0.6\,OG/dr=0.73+0.6OG/d with OGOGOG = distance of G above the waterline (positive up);
  • sss = factor from Table 2.3.4-4 as a function of the roll period T=2CB/GMT = 2CB/\sqrt{GM}T=2CB/GM​, with C=0.373+0.023 B/d−0.043 LWL/100C = 0.373 + 0.023\,B/d - 0.043\,L_{WL}/100C=0.373+0.023B/d−0.043LWL​/100.

Note that the Code places no upper cap on φ1\varphi_1φ1​; the 16° limit applies to the static angle φ0\varphi_0φ0​ only. For ships fitted with anti-rolling devices, the devices are assumed inoperative.

The factor tables are reproduced below. Intermediate values are obtained by linear interpolation.

Formulas

01Steady wind heeling lever
lw1=P A Z1000 g Δl_{w1} = \frac{P\,A\,Z}{1000\, g\, \Delta}lw1​=1000gΔPAZ​
SymbolDescriptionUnit
lw1l_{w1}lw1​Steady wind heeling lever (constant with heel)m
PPPWind pressure (504 Pa unrestricted service)Pa
AAAProjected lateral area above waterline (hull, superstructure, deck cargo)m^2
ZZZVertical lever: centroid of A to centre of underwater lateral area (≈ T/2)m
Δ\DeltaΔDisplacementt
ggg9.81m/s^2

Result unit m

02Gust wind heeling lever
lw2=1.5 lw1l_{w2} = 1.5\, l_{w1}lw2​=1.5lw1​

Result unit m

03Roll-back angle to windward
φ1=109 k X1 X2r s\varphi_1 = 109\, k\, X_1\, X_2 \sqrt{r\, s}φ1​=109kX1​X2​rs​
SymbolDescriptionUnit
φ1\varphi_1φ1​Roll angle to windward from static heeldeg
kkkBilge/keel factor (1.0 round bilge, 0.7 sharp bilge, table for bilge keels)-
X1X_1X1​Factor of B/d (Table 2.3.4-1)-
X2X_2X2​Factor of C_B (Table 2.3.4-2)-
rrr0.73 + 0.6 OG/d-
sssFactor of roll period T (Table 2.3.4-4)-

Result unit deg

04Roll period for the weather criterion
T=2 C BGM,C=0.373+0.023 Bd−0.043 LWL100T = \frac{2\,C\,B}{\sqrt{GM}}, \qquad C = 0.373 + 0.023\,\frac{B}{d} - 0.043\,\frac{L_{WL}}{100}T=GM​2CB​,C=0.373+0.023dB​−0.043100LWL​​
SymbolDescriptionUnit
TTTRoll periods
dddMean moulded draughtm
GMGMGMFluid metacentric heightm

Result unit s

05Energy balance
b=∫φ0φ2(GZ−lw2)dφ ≥ a=∫φ0−φ1φ0(lw2−GZ)dφb = \int_{\varphi_0}^{\varphi_2}\left(GZ - l_{w2}\right)d\varphi \ \ge\ a = \int_{\varphi_0-\varphi_1}^{\varphi_0}\left(l_{w2} - GZ\right)d\varphib=∫φ0​φ2​​(GZ−lw2​)dφ ≥ a=∫φ0​−φ1​φ0​​(lw2​−GZ)dφ
SymbolDescriptionUnit
φ0\varphi_0φ0​Static heel under steady wind l_w1deg
φ2\varphi_2φ2​min(second intersection, φf, 50°)deg

Result unit m·rad

GZ is negative for negative angles (windward side): GZ(−φ) = −GZ(φ) for a symmetric ship.

06Static heel limit
φ0≤min⁡(16°, 0.8 φdeck edge)\varphi_0 \le \min\left(16°,\ 0.8\,\varphi_{\text{deck edge}}\right)φ0​≤min(16°, 0.8φdeck edge​)

Result unit deg

Tables

Factor X1X_1X1​ (IS Code Table 2.3.4-1)

B/dB/dB/dX1X_1X1​
≤ 2.41.00
2.50.98
2.60.96
2.70.95
2.80.93
2.90.91
3.00.90
3.10.88
3.20.86
3.40.82
≥ 3.50.80
Source: IMO IS Code 2008 Part A, Table 2.3.4-1.

Factor X2X_2X2​ (IS Code Table 2.3.4-2)

CBC_BCB​X2X_2X2​
≤ 0.450.75
0.500.82
0.550.89
0.600.95
0.650.97
≥ 0.701.00
Source: IMO IS Code 2008 Part A, Table 2.3.4-2.

Factor kkk for bilge keels (IS Code Table 2.3.4-3)

100 Ak/(L B)100\,A_k/(L\,B)100Ak​/(LB)kkk
01.00
1.00.98
1.50.95
2.00.88
2.50.79
3.00.74
3.50.72
≥ 4.00.70
Source: IMO IS Code 2008 Part A, Table 2.3.4-3.

Factor sss (IS Code Table 2.3.4-4)

TTT [s]sss
≤ 60.100
70.098
80.093
120.065
140.053
160.044
180.038
≥ 200.035
Source: IMO IS Code 2008 Part A, Table 2.3.4-4.

Examples

#01

Weather criterion inputs for the example vessel

Worked example

Problem

Example vessel: Δ=6314\Delta = 6314Δ=6314 t, B=16B = 16B=16 m, d=5.5d = 5.5d=5.5 m, LWL=102L_{WL} = 102LWL​=102 m, CB=0.70C_B = 0.70CB​=0.70, fluid GM=0.70GM = 0.70GM=0.70 m, KGf=5.28KG_f = 5.28KGf​=5.28 m, projected lateral area above WL A=1450A = 1450A=1450 m² with centroid 7.2 m above WL, round bilge with bilge keels of total area Ak=24A_k = 24Ak​=24 m². Compute lw1l_{w1}lw1​, lw2l_{w2}lw2​, φ0\varphi_0φ0​, and φ1\varphi_1φ1​.

Solution

Wind levers. Z=7.2+5.5/2=9.95Z = 7.2 + 5.5/2 = 9.95Z=7.2+5.5/2=9.95 m.

lw1=504×1450×9.951000×9.81×6314=7,271,46061,940,340=0.117 m,lw2=0.176 ml_{w1} = \frac{504 \times 1450 \times 9.95}{1000 \times 9.81 \times 6314} = \frac{7{,}271{,}460}{61{,}940{,}340} = 0.117\ \text{m}, \qquad l_{w2} = 0.176\ \text{m}lw1​=1000×9.81×6314504×1450×9.95​=61,940,3407,271,460​=0.117 m,lw2​=0.176 m

Static heel. From the GZ curve (GZ≈0.70sin⁡φGZ \approx 0.70\sin\varphiGZ≈0.70sinφ initially): sin⁡φ0=0.117/0.70⇒φ0≈9.6°\sin\varphi_0 = 0.117/0.70 \Rightarrow \varphi_0 \approx 9.6°sinφ0​=0.117/0.70⇒φ0​≈9.6°. Deck edge immerses at ≈ 27°, so the limit is min⁡(16°,0.8×27°=21.6°)=16°\min(16°, 0.8 \times 27° = 21.6°) = 16°min(16°,0.8×27°=21.6°)=16° — satisfied.

Roll-back angle. B/d=2.91⇒X1=0.91B/d = 2.91 \Rightarrow X_1 = 0.91B/d=2.91⇒X1​=0.91 (interpolated). CB=0.70⇒X2=1.00C_B = 0.70 \Rightarrow X_2 = 1.00CB​=0.70⇒X2​=1.00. 100Ak/(LB)=2400/(102×16)=1.47⇒k=0.95100A_k/(LB) = 2400/(102 \times 16) = 1.47 \Rightarrow k = 0.95100Ak​/(LB)=2400/(102×16)=1.47⇒k=0.95. OG=KGf−d=5.28−5.50=−0.22OG = KG_f - d = 5.28 - 5.50 = -0.22OG=KGf​−d=5.28−5.50=−0.22 m; r=0.73+0.6×(−0.22/5.5)=0.73−0.024=0.706r = 0.73 + 0.6 \times (-0.22/5.5) = 0.73 - 0.024 = 0.706r=0.73+0.6×(−0.22/5.5)=0.73−0.024=0.706. C=0.373+0.023×2.91−0.043×1.02=0.373+0.067−0.044=0.396C = 0.373 + 0.023 \times 2.91 - 0.043 \times 1.02 = 0.373 + 0.067 - 0.044 = 0.396C=0.373+0.023×2.91−0.043×1.02=0.373+0.067−0.044=0.396; T=2×0.396×16/0.70=12.67/0.837=15.1T = 2 \times 0.396 \times 16/\sqrt{0.70} = 12.67/0.837 = 15.1T=2×0.396×16/0.70​=12.67/0.837=15.1 s ⇒s=0.049\Rightarrow s = 0.049⇒s=0.049 (interpolated between 14 s and 16 s).

φ1=109×0.95×0.91×1.00×0.706×0.049=94.2×0.186=17.5°\varphi_1 = 109 \times 0.95 \times 0.91 \times 1.00 \times \sqrt{0.706 \times 0.049} = 94.2 \times 0.186 = 17.5°φ1​=109×0.95×0.91×1.00×0.706×0.049​=94.2×0.186=17.5°

Energy balance. Area a is integrated from φ0−φ1=−7.9°\varphi_0 - \varphi_1 = -7.9°φ0​−φ1​=−7.9° to 9.6°9.6°9.6° between lw2l_{w2}lw2​ and the GZ curve; area b from 9.6°9.6°9.6° to φ2=min⁡(2nd intersection≈67°,φf=55°,50°)=50°\varphi_2 = \min(\text{2nd intersection} \approx 67°, \varphi_f = 55°, 50°) = 50°φ2​=min(2nd intersection≈67°,φf​=55°,50°)=50° between the GZ curve and lw2l_{w2}lw2​. With the GZ values of Example 5.4, area b is of the order of 0.20 m·rad and area a of the order of 0.04 m·rad, so the criterion is satisfied by a wide margin. In the stability software this integration is done at 1° steps; a hand check with 5° steps and the trapezoidal rule is adequate for verification.

References

IMO IS Code 2008Clause Part A, Ch. 2.3 (Severe wind and rolling criterion) incl. Tables 2.3.4-1 to 2.3.4-4Mandatory
IMO MSC.1/Circ.1200 (2006) Interim guidelines for alternative assessment of the weather criterionClause whole documentRecommended

Model-test based alternative for ships with unusual parameters (e.g. B/d > 3.5, OG/d outside −0.3 to 0.5, T > 20 s).

IMO IS Code 2008Clause Part B, Ch. 2.1.4 (Fishing vessels ≥ 45 m — weather criterion applies)Recommended