Back to section

NavArch Handbook

Chapter 4 / Section 4.2

Lines plan, body plan and offsets

The lines plan

The lines plan defines the moulded hull surface by three orthogonal sets of sections:

  1. Body plan — transverse sections (stations) projected on the midship plane. By convention, forward stations are drawn on the right-hand side and aft stations on the left.
  2. Sheer plan (profile) — buttock lines (vertical longitudinal planes parallel to CL) and the profile of stem, stern, deck at side and keel.
  3. Half-breadth plan — waterlines (horizontal planes) drawn for one side of the ship.

Diagonals are added to check fairness, particularly at the turn of bilge.

Table of offsets

The hull surface is tabulated as half-breadths yyy [m] at each station and each waterline, together with heights of deck at side, deck at centre, and the keel/rabbet line. Offsets are given to the moulded surface (inside of shell plating for steel; outside of hull for GRP, by convention of ISO 8666 for small craft — check which surface is used).

A typical set for hydrostatic integration uses:

  • 11 or 21 stations (0 = AP, 10 or 20 = FP), with half-stations near the ends where the curvature is high;
  • waterlines at equal spacing (e.g. every 0.5 m or 1.0 m) from baseline to the design or scantling waterline, plus intermediate waterlines near the baseline.

Fairing

A fair hull has smooth, continuous curvature in all three views. In manual fairing the three plans are iterated until every point agrees in all projections. In CAD (NURBS surfaces) fairness is checked with curvature combs and zebra stripes. Offsets used for hydrostatics must be taken from the faired surface.

Appendages

Rudder, propeller, shaft bossings, bilge keels, skegs and sea chests are not part of the moulded hull. Their volume is added separately as the appendage allowance when computing displacement (typically 0.5–2 % of moulded volume depending on ship type).

Coordinate system (recommended for the handbook and for CAD exchange)

  • xxx positive forward, origin at AP (or at midship — state which);
  • yyy positive to port (ISO 7462) — note that some software uses starboard positive;
  • zzz positive upward, origin at baseline. Always state the origin and sign convention on every hydrostatic table and drawing.

Formulas

01Appendage-corrected displacement volume
∇total=∇moulded (1+ashell)+∇app\nabla_{\text{total}} = \nabla_{\text{moulded}}\,(1 + a_{\text{shell}}) + \nabla_{\text{app}}∇total​=∇moulded​(1+ashell​)+∇app​
SymbolDescriptionUnit
∇total\nabla_{\text{total}}∇total​Total immersed volumem^3
∇moulded\nabla_{\text{moulded}}∇moulded​Moulded volume from offsetsm^3
ashella_{\text{shell}}ashell​Shell plating allowance (steel: 0.005–0.008)-
∇app\nabla_{\text{app}}∇app​Volume of appendages (rudder, bossings, bilge keels, etc.)m^3

Result unit m^3

The shell allowance is approximately S_wet × t_shell for the immersed shell.

Tables

Typical appendage allowances (percent of moulded displacement volume)

Ship typeAllowance %Main contributors
Single-screw cargo ship0.5–1.0Shell plating, rudder, bilge keels
Twin-screw ship with bossings/brackets1.0–2.0Shell, shaft bossings, brackets, rudders
Fishing vessel with nozzle and large skeg1.5–2.5Skeg, nozzle, rudder, shell
GRP small craft (offsets to outside of hull)0.2–0.8Keel, rudder, skeg (no shell allowance)
Source: Indicative values after Rawson & Tupper (2001) Vol. 1 Ch. 3 and common practice; replace with calculated volumes when the appendage geometry is known.

References

ISO 7462:1985 Shipbuilding — Principal ship dimensions — Terminology and definitions for computer applicationsClause whole documentRecommended

Defines coordinate axes and dimension terminology for data exchange.

ISO 8666:2020 Small craft — Principal dataClause whole documentRecommended

Dimension definitions for craft under 24 m (used by ISO 12215/12217 and the RCD).

Tupper, Introduction to Naval Architecture, 5th ed. (2013)Clause Ch. 2 (Definition and regulation)Textbook