Back to section

NavArch Handbook

Chapter 5 / Section 5.2

The inclining experiment

Purpose

To determine the lightship displacement and the lightship centre of gravity (KGKGKG and LCGLCGLCG, and TCGTCGTCG if not zero) of the completed ship by measurement. Required by SOLAS II-1 Reg. 5 for passenger and cargo ships and by the IS Code (Part B, Ch. 8) which gives the detailed procedure; classification societies witness it on behalf of the flag state.

Principle

A known mass www is moved a known transverse distance ddd; the resulting heel φ\varphiφ is measured. From GG1=wd/ΔGG_1 = w d/\DeltaGG1​=wd/Δ and tan⁡φ=GG1/GM\tan\varphi = GG_1/GMtanφ=GG1​/GM:

GM=w dΔtan⁡φGM = \frac{w\,d}{\Delta\tan\varphi}GM=Δtanφwd​

With KMKMKM from the hydrostatics at the measured draughts, KG=KM−GMKG = KM - GMKG=KM−GM.

Procedure (IS Code 2008 Part B Ch. 8 and Annex 1, summarised)

  1. Ship as complete as possible; list of items to be added/removed with masses and centres; tanks empty or pressed full (minimise free surfaces); no slack tanks except where unavoidable — record them.
  2. Calm, sheltered water; wind < ~ 3 Bft; mooring lines slack; gangway lifted; no persons moving.
  3. Measure draughts at marks (both sides, forward, midship, aft) and the water density; compute displacement, KMKMKM, LCFLCFLCF from the hydrostatics for the measured trim.
  4. Inclining weights: total mass sufficient to produce 1°–4° heel (minimum about 1°); typically 4 weights, moved in 8 shifts (e.g. 0, 1P, 2P, 1P, 0, 1S, 2S, 1S, 0) producing at least 8 readings.
  5. Heel measured by at least 2 (preferably 3) pendulums of length ≥ 3 m (deflection read on a batten with the pendulum damped in oil), or U-tubes or inclinometers.
  6. Plot heeling moment wdw dwd against tan⁡φ\tan\varphitanφ for each pendulum; the points must lie on a straight line through the origin. Non-linearity indicates free surface, a weight touching, or a mooring restraint.
  7. GMas inclined=GM_{\text{as inclined}} = GMas inclined​= slope / Δ\DeltaΔ; correct for free surface of any slack tank; obtain KGas inclinedKG_{\text{as inclined}}KGas inclined​.
  8. Remove items to be removed and add items to be added (with their centres) to arrive at the lightship Δ\DeltaΔ, KGKGKG, LCGLCGLCG.

Corrections and pitfalls

  • Free surface moments of slack tanks (Section 5.3) must be added to the measured GMGMGM to obtain the solid GMGMGM (the measured value is the fluid GMGMGM).
  • Use KMKMKM for the actual trim and displacement, not the design value.
  • Pendulum deflection δ\deltaδ over length lll: tan⁡φ=δ/l\tan\varphi = \delta/ltanφ=δ/l.
  • Lightship check: if the lightship displacement or LCGLCGLCG differs significantly from the previous one (SOLAS: deviation of lightship > 2 % or LCGLCGLCG > 1 % of LLL for passenger ships), a new inclining test and a new stability booklet are required.

Formulas

01Metacentric height from inclining
GM=w dΔ tan⁡φGM = \frac{w\, d}{\Delta\,\tan\varphi}GM=Δtanφwd​
SymbolDescriptionUnit
wwwMass movedt
dddTransverse distance moved (centre to centre)m
Δ\DeltaΔDisplacement as inclined (from measured draughts and water density)t
φ\varphiφAngle of heel produceddeg

Result unit m

02Heel from pendulum deflection
tan⁡φ=δl\tan\varphi = \frac{\delta}{l}tanφ=lδ​
SymbolDescriptionUnit
δ\deltaδPendulum deflection on the battenm
lllPendulum lengthm

Result unit -

03KG as inclined
KGincl=KM−GMincl−GGFSKG_{\text{incl}} = KM - GM_{\text{incl}} - GG_{FS}KGincl​=KM−GMincl​−GGFS​
SymbolDescriptionUnit
GGFSGG_{FS}GGFS​Free surface correction of slack tanks present during the test. The pendulum measures the fluid GM; solid GM = fluid GM + GG_FS and solid KG = KM − solid GM.m

Result unit m

The pendulum measures the fluid GM. Solid GM = fluid GM + GG_FS; solid KG = KM − solid GM.

04Lightship KG from as-inclined condition
KGlight=ΔinclKGincl−∑woff Kgoff+∑won KgonΔincl−∑woff+∑wonKG_{\text{light}} = \frac{\Delta_{\text{incl}}KG_{\text{incl}} - \sum w_{\text{off}}\,Kg_{\text{off}} + \sum w_{\text{on}}\,Kg_{\text{on}}}{\Delta_{\text{incl}} - \sum w_{\text{off}} + \sum w_{\text{on}}}KGlight​=Δincl​−∑woff​+∑won​Δincl​KGincl​−∑woff​Kgoff​+∑won​Kgon​​
SymbolDescriptionUnit
woffw_{\text{off}}woff​Masses on board during the test that are not part of lightship (inclining weights, temporary equipment, people, slack liquids)t
wonw_{\text{on}}won​Lightship items missing at the time of the testt

Result unit m

Tables

Inclining test: acceptance limits and requirements (IS Code 2008 Part B Ch. 8 / Annex 1)

ItemRequirement
Angle of heel per shiftSufficient for accuracy; total heel each side 1°–4°
Number of weight movementsEight (standard), giving at least 8 readings
PendulumsMinimum 2 (3 recommended), length ≥ 3 m, in different locations
Alternative devicesU-tubes, inclinometers — with Administration's acceptance
Free surfacesTanks empty and clean, or pressed full; slack tanks minimised and recorded
WeatherCalm; wind not to cause measurable heel
MooringSlack lines; shore gangway removed
PlotHeeling moment vs tan φ must be linear through origin
Draught readingsBoth sides at forward, midship and aft marks; water density sampled
Source: IMO IS Code 2008, Part B, Ch. 8 and Annex 1 (Detailed guidance for the conduct of an inclining test). Part B is recommendatory but universally applied by Administrations and class.

Examples

#01

Inclining experiment on the example vessel

Worked example

Problem

At the inclining test the displacement from the draught survey is Δ=6314\Delta = 6314Δ=6314 t and KM=5.98KM = 5.98KM=5.98 m. Four weights of 2.5 t each (total 10 t) are moved 12.0 m across the deck. The mean deflection of a 6.00 m pendulum is 150 mm. All tanks are empty except one fuel tank with a free-surface moment of 435 t·m. Determine the solid GMGMGM and KGKGKG as inclined.

Solution

Heel: tan⁡φ=0.150/6.00=0.0250\tan\varphi = 0.150/6.00 = 0.0250tanφ=0.150/6.00=0.0250 (φ=1.43°\varphi = 1.43°φ=1.43°) — within the 1°–4° range.

Fluid GM:

GMfluid=10×12.06314×0.0250=120157.9=0.760 mGM_{\text{fluid}} = \frac{10 \times 12.0}{6314 \times 0.0250} = \frac{120}{157.9} = 0.760\ \text{m}GMfluid​=6314×0.025010×12.0​=157.9120​=0.760 m

Free surface correction: GGFS=435/6314=0.069GG_{FS} = 435/6314 = 0.069GGFS​=435/6314=0.069 m.

Solid GM: 0.760+0.069=0.8290.760 + 0.069 = 0.8290.760+0.069=0.829 m.

Solid KGincl=5.98−0.829=5.15KG_{\text{incl}} = 5.98 - 0.829 = 5.15KGincl​=5.98−0.829=5.15 m.

The inclining weights (10 t at Kg=11.5Kg = 11.5Kg=11.5 m) are then removed and lightship items added to obtain the lightship KGKGKG — the removal of 10 t at 11.5 m alone lowers KGKGKG by (10×(11.5−5.15))/(6314−10)=0.010(10 \times (11.5 - 5.15))/(6314 - 10) = 0.010(10×(11.5−5.15))/(6314−10)=0.010 m to 5.14 m.

References

IMO IS Code 2008 (Res. MSC.267(85))Clause Part B, Ch. 8 (Determination of lightship parameters) and Annex 1Recommended

Made mandatory in practice by SOLAS II-1 Reg. 5 and by flag state regulations (e.g. NMA).

SOLAS 1974 as amendedClause Ch. II-1, Reg. 5 (Intact stability information) and Reg. 5-1Mandatory
DNV Rules for Classification — Ships, Pt.3 Ch.15 (Stability)Clause Sec. 1 (Inclining test and lightweight survey)Mandatory

Check the edition in force for the project.